Abstract: Methods for organizing web data into groups in order
to analyze web-based hypertext data and facilitate data availability
are very important in terms of the number of documents available
online. Thereby, the task of clustering web-based document structures
has many applications, e.g., improving information retrieval on the
web, better understanding of user navigation behavior, improving web
users requests servicing, and increasing web information accessibility.
In this paper we investigate a new approach for clustering web-based
hypertexts on the basis of their graph structures. The hypertexts will
be represented as so called generalized trees which are more general
than usual directed rooted trees, e.g., DOM-Trees. As a important
preprocessing step we measure the structural similarity between the
generalized trees on the basis of a similarity measure d. Then,
we apply agglomerative clustering to the obtained similarity matrix
in order to create clusters of hypertext graph patterns representing
navigation structures. In the present paper we will run our approach
on a data set of hypertext structures and obtain good results in
Web Structure Mining. Furthermore we outline the application of
our approach in Web Usage Mining as future work.
Abstract: In automotive systems almost all steps concerning the
calibration of several control systems, e.g., low idle governor or
boost pressure governor, are made with the vehicle because the timeto-
production and cost requirements on the projects do not allow for
the vehicle analysis necessary to build reliable models. Here is
presented a procedure using parametric and NN (neural network)
models that enables the generation of vehicle system models based
on normal ECU engine control unit) vehicle measurements. These
models are locally valid and permit pre and follow-up calibrations so
that, only the final calibrations have to be done with the vehicle.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: This study analyzes characteristics determining
member’s willingness to invest in cooperatives using ordered logit
model. The data were collected in a field survey among 122
cooperative members in north-central China. The descriptive analysis
of survey evidence suggests that cooperatives in China generally
having poor ability to deliver the processing services related to
product package, grading, and storage, performing worse in
profitability, inability of providing returns to capital and obtaining
agricultural loan. The regression results demonstrate that members’
farm size, their satisfaction with cooperative price preferential
services, attitudes toward cooperative operational scale and
development potential have statistically significant impact on
willingness to invest.
Abstract: In the present work, an attempt has been made to
understand the feasibility of using UHF technique for identification
of any corona discharges/ arcing in insulating material due to water
droplets. The sensors of broadband type are useful for identification
of such discharges. It is realised that arcing initiated by liquid droplet
radiates UHF signals in the entire bandwidth up to 2 GHz. The
frequency content of the UHF signal generated due to corona/arcing
is not much varied in epoxy nanocomposites with different weight
percentage of clay content. The exfoliated/intercalated properties
were analysed through TEM studies. It is realized that corona
initiated discharges are of intermittent process. The hydrophobicity
of the material characterized through contact angle measurement. It
is realized that low Wt % of nanoclay content in epoxy resin reduces
the surface carbonization due to arcing/corona discharges. The results
of the study with gamma irradiated specimen indicates that contact
angle, discharge inception time and evaporation time of the liquid are
much lower than the virgin epoxy nanocomposite material.
Abstract: In today-s competitive global business environment,
the concept of supply chain management (SCM) continues to become
increasingly market-oriented, shifting the primary driver of the value
chain from supply to demand. Recent recommendations encourage
researchers to focus investigations on the supply chain process
integration (SCPI) capabilities that integrate a focal firm with its
network of suppliers and business customers to create value for it.
However, theoretical and empirical researches pertaining to the
antecedents and consequences of a focal firm-s SCPI capabilities have
been limited and piecemeal. The purpose of this study is to investigate
the critical determinants and consequences of a focal firm-s SCPI
capabilities. We test our proposed research framework using a sample
of 139 sales managers of manufacturing industries in Taiwan, our
research findings show that (1) both perceived business customer-s
power and focal firm-s market-oriented culture positively influences a
focal firm-s SCPI capabilities, and (2) SCPI capabilities positively
influence a focal firm-s SCM performance, both operational and
strategic benefits. Implications for practitioners and researchers and
suggestions for future research are also addressed in this study.
Abstract: Dehydration of methanol to dimethyl ether (DME)
over a commercial Al2O3 catalyst was studied in an isothermal integral
fixed bed reactor. The experiments were performed on the temperature
interval 513-613 K, liquid hourly space velocity (LHSV) of 0.9-2.1h-1,
pressures between 0.1 and 1.0 MPa. The effect of different operation
conditions on the dehydration of methanol was investigated in a
laboratory scale experiment. A new intrinsic kinetics equation based
on the mechanism of Langmuir-Hinshelwood dissociation adsorption
was developed for the dehydration reaction by fitting the expressions
to the experimental data. An activation energy of 67.21 kJ/mol was
obtained for the catalyst with the best performance. Statistic test
showed that this new intrinsic kinetics equation was acceptable.
Abstract: The IEEE802.16 standard which has emerged as
Broadband Wireless Access (BWA) technology, promises to deliver
high data rate over large areas to a large number of subscribers in the
near future. This paper analyze the effect of overheads over capacity
of downlink (DL) of orthogonal frequency division multiple access
(OFDMA)–based on the IEEE802.16e mobile WiMAX system with
and without overheads. The analysis focuses in particular on the
impact of Adaptive Modulation and Coding (AMC) as well as
deriving an algorithm to determine the maximum numbers of
subscribers that each specific WiMAX sector may support. An
analytical study of the WiMAX propagation channel by using Cost-
231 Hata Model is presented. Numerical results and discussion
estimated by using Matlab to simulate the algorithm for different
multi-users parameters.
Abstract: This paper presents a conceptual model of agreement
options on negotiation support for civil engineering decision. The
negotiation support facilitates the solving of group choice decision
making problems in civil engineering decision to reduce the impact
of mud volcano disaster in Sidoarjo, Indonesia. The approach based
on application of analytical hierarchy process (AHP) method for
multi criteria decision on three level of decision hierarchy.
Decisions for reducing impact is very complicated since many
parties involved in a critical time. Where a number of stakeholders
are involved in choosing a single alternative from a set of solution
alternatives, there are different concern caused by differing
stakeholder preferences, experiences, and background. Therefore, a
group choice decision support is required to enable each stakeholder
to evaluate and rank the solution alternatives before engaging into
negotiation with the other stakeholders. Such civil engineering
solutions as alternatives are referred to as agreement options that are
determined by identifying the possible stakeholder choice, followed
by determining the optimal solution for each group of stakeholder.
Determination of the optimal solution is based on a game theory
model of n-person general sum game with complete information that
involves forming coalitions among stakeholders.
Abstract: Trust and Energy consumption is the most challenging
issue in routing protocol design for Mobile ad hoc networks
(MANETs), since mobile nodes are battery powered and nodes
behaviour are unpredictable. Furthermore replacing and recharging
batteries and making nodes co-operative is often impossible in
critical environments like military applications. In this paper, we
propose a trust based energy aware routing model in MANET.
During route discovery, node with more trust and maximum energy
capacity is selected as a router based on a parameter called
'Reliability'. Route request from the source is accepted by a node
only if its reliability is high. Otherwise, the route request is
discarded. This approach forms a reliable route from source to
destination thus increasing network life time, improving energy
utilization and decreasing number of packet loss during transmission.
Abstract: Tomato nutrition value, color, flavor of their fruits and products depends mainly on lycopene, β-carotene, ascorbic acid, sugars and their ratio. The two most important carotenoids in fruits of tomato are lycopene, which determined fruits red color, and β- carotene, which accounts for approximately 7% of the tomato carotenoids. Therefore, tomato products and their quality can be well characterized by the content of these elements.Maturity at harvest is very important to composition and quality of tomatoes. This is especially a problem with tomatoes picked green since it is difficult to differentiate between mature and immature-green fruits. Typical and advanced mature-green tomatoes will usually attain a much better flavor than those picked at the immature or partially mature stages.To better understand the synthesis of biochemical compounds, their concentration should be compared not only at the last stage of maturity, but also during all fruit ripening period in different varieties.
Abstract: A model-free robust control (MFRC) approach is proposed for position control of robot manipulators in the state space. The control approach is verified analytically to be robust subject to uncertainties including external disturbances, unmodeled dynamics, and parametric uncertainties. There is a high flexibility to work on different systems including actuators by the use of the proposed control approach. The proposed control approach can guarantee the robustness of control system. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a satisfactory performance for control system under technical specifications. KeywordsModel-free, robust control, position control, PUMA 560.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: The iris recognition technology is the most accurate,
fast and less invasive one compared to other biometric techniques
using for example fingerprints, face, retina, hand geometry, voice or
signature patterns. The system developed in this study has the
potential to play a key role in areas of high-risk security and can
enable organizations with means allowing only to the authorized
personnel a fast and secure way to gain access to such areas. The
paper aim is to perform the iris region detection and iris inner and
outer boundaries localization. The system was implemented on
windows platform using Visual C# programming language. It is easy
and efficient tool for image processing to get great performance
accuracy. In particular, the system includes two main parts. The first
is to preprocess the iris images by using Canny edge detection
methods, segments the iris region from the rest of the image and
determine the location of the iris boundaries by applying Hough
transform. The proposed system tested on 756 iris images from 60
eyes of CASIA iris database images.
Abstract: Power systems and transformer are intrinsic apparatus, therefore its reliability and safe operation is important to determine their operation conditions, and the industry uses quality control tests in the insulation design of oil filled transformers. Hence the service period effect on AC dielectric strength is significant. The effect of aging on transformer oil physical, chemical and electrical properties was studied using the international testing methods for the evaluation of transformer oil quality. The study was carried out on six transformers operate in the field and for monitoring periods over twenty years. The properties which are strongly time dependent were specified and those which have a great impact on the transformer oil acidity, breakdown voltage and dissolved gas analysis were defined. Several tests on the transformers oil were studied to know the time of purifying or changing it, moreover prediction of the characteristics of it under different operation conditions.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part
during its manufacturing process. These manufacturing dimensions
also serve to satisfy not only the functional requirements given in
the definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the
wear of the cutting tool. In this paper, an experimental study on the
influence of the wear of the cutting tool (systematic dispersions) is
explored. This study was carried out on three stages .The first stage
allows machining without elimination of dispersions (random,
systematic) so the tolerances of manufacture according to total
dispersions. In the second stage, the results of the first stage are
filtered in such way to obtain the tolerances according to random
dispersions. Finally, from the two previous stages, the systematic
dispersions are generated. The objective of this study is to model
by the least squares method the error of manufacture based on
systematic dispersion. Finally, an approach of optimization of the
manufacturing tolerances was developed for machining on a CNC
machine tool
Abstract: The authors present optimization parameters of rotary
positioner controller in hard disk drive servo track writing process
using coefficient diagram method; CDM. Due to estimation
parameters in PI Positioning Control System by expected ratio
method cannot meet the required specification of response
effectively, we suggest coefficient diagram method for defining
controller parameters under the requirement of the system. Finally,
the simulation results show that our proposed method can improve
the problem in tuning parameter of rotary positioner controller. It is
satisfied specification of performance of control system. Furthermore,
it is very convenient as a fast adjustment damping ratio as well as a
high speed response.
Abstract: The majority of micro-entrepreneurs in Malaysia
operate very small-scaled business activities such as food stalls,
burger stalls, night market hawkers, grocery stores, constructions,
rubber and oil palm small holders, and other agro-based services and
activities. Why are they venturing into entrepreneurship - is it for
survival, out of interest or due to encouragement and assistance from
the local government? And why is it that some micro-entrepreneurs
are lagging behind in entrepreneurship, and what do they need to
rectify this situation so that they are able to progress further?
Furthermore, what are the skills that the micro entrepreneurs should
developed to transform them into successful micro-enterprises and
become small and medium-sized enterprises (SME)? This paper
proposes a 7-Step approach that can serve as a basis for identification
of critical entrepreneurial success factors that enable policy makers,
practitioners, consultants, training managers and other agencies in
developing tools to assist micro business owners. This paper also
highlights the experience of one of the successful companies in
Malaysia that has transformed from micro-enterprise to become a
large organization in less than 10 years.
Abstract: This paper presents an efficient emission constrained
hydrothermal scheduling algorithm that deals with nonlinear
functions such as the water discharge characteristics, thermal cost,
and transmission loss. It is then incorporated into the hydrothermal
coordination program. The program has been tested on a practical
utility system having 32 thermal and 12 hydro generating units. Test
results show that a slight increase in production cost causes a
substantial reduction in emission.
Abstract: The expansion mechanism of a partially ionized plasma produced by laser interaction with solid target (copper) is studied. For this purpose we use a hydrodynamical model which includes a source term combined with Saha's equation. The obtained self-similar solution in the limit of quasi-neutrality shows that the expansion, at the earlier stage, is driven by the combination of thermal pressure and electrostatic potential. They are of the same magnitude. The initial ionized fraction and the temperature are the leading parameters of the expanding profiles,