Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: Experimental studies to investigate the depth of the
scour conducted at a side-weir intersection located at the 1800 curved
flume which located Hydraulic Laboratory of Yıldız Technical
University, Istanbul, Turkey. Side weirs were located at the middle of
the straight part of the main channel. Three different lengths (25, 40
and 50 cm) and three different weir crest height (7, 10 and 12 cm) of
the side weir placed on the side weir station. There is no scour when
the material is only kaolin. Therefore, the cohesive bed was prepared
by properly mixing clay material (kaolin) with 31% sand in all
experiments. Following 24h consolidation time, in order to observe
the effect of flow intensity on the scour depth, experiments were
carried out for five different upstream Froude numbers in the range of
0.33-0.81.
As a result of this study the relation between scour depth and
upstream flow intensity as a function of time have been established.
The longitudinal velocities decreased along the side weir; towards the
downstream due to overflow over the side-weirs. At the beginning,
the scour depth increases rapidly with time and then asymptotically
approached constant values in all experiments for all side weir
dimensions as in non-cohesive sediment. Thus, the scour depth
reached equilibrium conditions. Time to equilibrium depends on the
approach flow intensity and the dimensions of side weirs. For
different heights of the weir crest, dimensionless scour depths
increased with increasing upstream Froude number. Equilibrium
scour depths which formed 7 cm side-weir crest height were obtained
higher than that of the 12 cm side-weir crest height. This means when
side-weir crest height increased equilibrium scour depths decreased.
Although the upstream side of the scour hole is almost vertical, the
downstream side of the hole is inclined.
Abstract: This paper examines the utilization of public-private
partnerships for the building and operation of wastewater treatment
plants. Our research focuses on risk allocation in this kind of projects.
Our analysis builds on more than hundred wastewater treatment
plants built and operated through PPP projects in Aragon (Spain).
The paper illustrates the consequences of an inadequate management
of construction risk and an unsuitable transfer of demand risk in
wastewater treatment plants. It also shows that the involvement of
many public bodies at local, regional and national level further
increases the complexity of this kind of projects and make time
delays more likely.
Abstract: Diagram and drawing are important ways to
communicate and the reproduce of architectural design, Due to the
development of information and communication technology, the
professional thinking of architecture and interior design are also
change rapidly. In development process of design, diagram always
play very important role. This study is based on diagram theories,
observe and record interaction between man and objects, objects and
space, and space and time in a modern nuclear family. Construct a
method for diagram to systematically and visualized describe the
space plan of a modern nuclear family toward an intelligent design, to
assist designer to retrieve information and review event pattern of past
and present.
Abstract: Durian is the flagship fruit of Mindanao and there is
an abundance of several cultivars with many confusing identities/
names.
The project was conducted to develop procedure for reliable and
rapid detection and sorting of durian planting materials. Moreover, it
is also aimed to establish specific genetic or DNA markers for routine
testing and authentication of durian cultivars in question.
The project developed molecular procedures for routine testing.
SSR primers were also screened and identified for their utility in
discriminating durian cultivars collected.
Results of the study showed the following accomplishments:
1. Twenty (29) SSR primers were selected and identified based on
their ability to discriminate durian cultivars,
2. Optimized and established standard procedure for identification
and authentication of Durian cultivars
3. Genetic profile of durian is now available at Biotech Unit
Our results demonstrate the relevance of using molecular
techniques in evaluating and identifying durian clones. The most
polymorphic primers tested in this study could be useful tools for
detecting variation even at the early stage of the plant especially for
commercial purposes. The process developed combines the efficiency
of the microsatellites development process with the optimization of
non-radioactive detection process resulting in a user-friendly protocol
that can be performed in two (2) weeks and easily incorporated into
laboratories about to start microsatellite development projects. This
can be of great importance to extend microsatellite analyses to other
crop species where minimal genetic information is currently
available. With this, the University can now be a service laboratory
for routine testing and authentication of durian clones.
Abstract: The aim of this paper is to present the concept of an
agile enterprise model and to initiate discussion on the research
assumptions of the model presented. The implementation of the
research project "The agility of enterprises in the process of adapting
to the environment and its changes" began in August 2014 and is
planned to last three years. The article has the form of a work-inprogress
paper which aims to verify and initiate a debate over the
proposed research model. In the literature there are very few
publications relating to research into agility; it can be concluded that
the most controversial issue in this regard is the method of measuring
agility. In previous studies the operationalization of agility was often
fragmentary, focusing only on selected areas of agility, for example
manufacturing, or analysing only selected sectors. As a result the
measures created to date can only be treated as contributory to the
development of precise measurement tools. This research project
aims to fill a cognitive gap in the literature with regard to the
conceptualization and operationalization of an agile company. Thus,
the original contribution of the author of this project is the
construction of a theoretical model that integrates manufacturing
agility (consisting mainly in adaptation to the environment) and
strategic agility (based on proactive measures). The author of this
research project is primarily interested in the attributes of an agile
enterprise which indicate that the company is able to rapidly adapt to
changing circumstances and behave pro-actively.
Abstract: The atmospheres in many cities along the coastal lines
in the world have been rapidly changed to coastal-industrial
atmosphere. Hence, it is vital to investigate the corrosion behavior of
steel exposed to this kind of environment. In this present study,
Electrochemical Impedance Spectrography (EIS) and film thickness
measurement were applied to monitor the corrosion behavior of
weathering steel covered with a thin layer of the electrolyte in a
wet-dry cyclic condition, simulating a coastal-industrial environment
at 25oC and 60% RH. The results indicate that in all cycles, the
corrosion rate increases during the drying process due to an increase in
anion concentration and an acceleration of oxygen diffusion enhanced
by the effect of the thinning out of the electrolyte. During the wet-dry
cyclic corrosion test, the long-term corrosion behavior of this steel
depends on the periods of exposure. Corrosion process is first
accelerated and then decelerated. The decelerating corrosion process is
contributed to the formation of the protective rust, favored by the
wet-dry cycle and the acid regeneration process during the rusting
process.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: This paper adopts a two-stage data envelopment
analysis to explore the impacts of financial development and bank
operating scale on bank efficiencies. The sample comprises
unbalanced panel data of 32 Taiwanese listed domestic commercial
banks over the period 1998 to 2013. Empirical results show that pure
technical efficiency is positively related to financial development,
whereas the effect of financial development on scale efficiency is
insignificant. Enlargement of bank operating scale improves bank
efficiencies, but the efficiency gains are decreased gradually when the
scale increases. Increases in capital adequacy ratio and market power
of loans lead into a growth of bank efficiencies.
Abstract: The effect of additional magnesium oxide (MgO) was
investigated by using the tungsten oxide supported on silica catalyst
(WOx/SiO2) physically mixed with MgO in a weight ratio 1:1. The
both fresh and spent catalysts were characterized by FT-Raman
spectrometer, UV-Vis spectrometer, X-Ray diffraction (XRD) and
temperature programmed oxidation (TPO). The results indicated that
the additional MgO could enhance the conversion of trans-2-butene
due to isomerization reaction. However, adding MgO would increase
the amount of coke deposit on the WOx/SiO2 catalyst. The TPO
profile presented two peaks when the WOx/SiO2 catalyst was
physically mixed with MgO. The further peak was suggested that
came from coke precursor could be produced by isomerization
reaction of undesired product. Then, the occurred coke precursor
could deposit and form coke on the acid catalyst.
Abstract: Failure of typical seismic frames has been found by
plastic hinge occurring on beams section near column faces. On the
other hand, the seismic capacity of the frames can be enhanced if the
plastic hinges of the beams are shifted away from the column faces.
This paper presents detailing of reinforcements in the interior beam–
column connections aiming to relocate the plastic hinge of reinforced
concrete and precast concrete frames. Four specimens were tested
under quasi-static cyclic load including two monolithic specimens
and two precast specimens. For one monolithic specimen, typical
seismic reinforcement was provided and considered as a reference
specimen named M1. The other reinforced concrete frame M2
contained additional intermediate steel in the connection area
compared with the specimen M1. For the precast specimens,
embedded T-section steels in joint were provided, with and without
diagonal bars in the connection area for specimen P1 and P2,
respectively. The test results indicated the ductile failure with beam
flexural failure in monolithic specimen M1 and the intermediate steel
increased strength and improved joint performance of specimen M2.
For the precast specimens, cracks generated at the end of the steel
inserts. However, slipping of reinforcing steel lapped in top of the
beams was seen before yielding of the main bars leading to the brittle
failure. The diagonal bars in precast specimens P2 improved the
connection stiffness and the energy dissipation capacity.
Abstract: Design concepts of real-time embedded system can be
realized initially by introducing novel design approaches. In this
literature, model based design approach and in-the-loop testing were
employed early in the conceptual and preliminary phase to formulate
design requirements and perform quick real-time verification. The
design and analysis methodology includes simulation analysis, model
based testing, and in-the-loop testing. The design of conceptual driveby-
wire, or DBW, algorithm for electronic control unit, or ECU, was
presented to demonstrate the conceptual design process, analysis, and
functionality evaluation. The concepts of DBW ECU function can be
implemented in the vehicle system to improve electric vehicle, or EV,
conversion drivability. However, within a new development process,
conceptual ECU functions and parameters are needed to be evaluated.
As a result, the testing system was employed to support conceptual
DBW ECU functions evaluation. For the current setup, the system
components were consisted of actual DBW ECU hardware, electric
vehicle models, and control area network or CAN protocol. The
vehicle models and CAN bus interface were both implemented as
real-time applications where ECU and CAN protocol functionality
were verified according to the design requirements. The proposed
system could potentially benefit in performing rapid real-time
analysis of design parameters for conceptual system or software
algorithm development.
Abstract: Rehabilitation of dam components such as foundations, buttresses, spillways and overtopping protection require a wide range of construction and design methodologies. Geotechnical Engineering considerations play an important role in the design and construction of foundations of new dams. Much investigation is required to assess and evaluate the existing dams. The application of roller compacting concrete (RCC) has been accepted as a new method for constructing new dams or rehabilitating old ones. In the past 40 years there have been so many changes in the usage of RCC and now it is one of most satisfactory solutions of water and hydropower resource throughout the world. The considerations of rehabilitation and construction of dams might differ due to upstream reservoir and its influence on penetrating and dewatering of downstream, operations requirements and plant layout. One of the advantages of RCC is its rapid placement which allows the dam to be operated quickly. Unlike ordinary concrete it is a drier mix, and stiffs enough for compacting by vibratory rollers. This paper evaluates some different aspects of RCC and focuses on its preparation progress.
Abstract: Cloud computing is the innovative and leading
information technology model for enabling convenient, on-demand
network access to a shared pool of configurable computing resources
that can be rapidly provisioned and released with minimal
management effort. In this paper, we aim at the development of
workflow management system for cloud computing platforms based
on our previous research on the dynamic allocation of the cloud
computing resources and its workflow process. We took advantage of
the HTML5 technology and developed web-based workflow interface.
In order to enable the combination of many tasks running on the cloud
platform in sequence, we designed a mechanism and developed an
execution engine for workflow management on clouds. We also
established a prediction model which was integrated with job queuing
system to estimate the waiting time and cost of the individual tasks on
different computing nodes, therefore helping users achieve maximum
performance at lowest payment. This proposed effort has the potential
to positively provide an efficient, resilience and elastic environment
for cloud computing platform. This development also helps boost user
productivity by promoting a flexible workflow interface that lets users
design and control their tasks' flow from anywhere.
Abstract: In today’s rapidly changing and increasingly complex
environment, organizations have relied on their members’ positive
attitude toward their employers. In particular, employees’
organizational commitment (primarily, the affective component) has
been recognized as an essential component of organizational
functioning and success. Hence, identifying the determinants of
affective commitment is one of the most important research issues.
This study tested the influence of leader-member exchange (LMX)
and exchange ideology on employee’s affective commitment. In
addition, the interactive effect of LMX and exchange ideology was
examined. Data from 198 members of the Korean military supports
each of the hypotheses. Lastly, implications for research and directions
for future research are discussed.
Abstract: Due to rapid pressured of population growth, city has
started to lose its old tradition. City becomes congested with
uncomfortably living. Urban renewal refers orderly development of
settlements as well as land redevelopment. For this paper Chittagong
city has been selected as study area. It had a great tradition but it has
been losing its concord. Land use pattern of this place is also
haphazard due to lack of planning intervention. Renewal plan is
needed to ascertain suitable redevelopment and to recommend on
preservation of city heritage structure. The goal of this study is to
prepare a renewal plan using local planning approach. Social impact
methods have been used to achieve this goal. Both primary and
secondary data are used to achieve the goal. This study may find out
a complete solution for healthy living in old Part of city. This study
will help to preserve its tradition and makes urban lives more livable.
Abstract: This study presented to reduce earthquake damage and
emergency rehabilitation of critical structures such as schools, hightech
factories, and hospitals due to strong ground motions associated
with climate changes. Regarding recent trend, a strong earthquake
causes serious damage to critical structures and then the critical
structure might be influenced by sequence aftershocks (or tsunami)
due to fault plane adjustments. Therefore, in order to improve seismic
performance of critical structures, retrofitted or strengthening study
of the structures under aftershocks sequence after emergency
rehabilitation of the structures subjected to strong earthquakes is
widely carried out. Consequently, this study used composite material
for emergency rehabilitation of the structure rather than concrete and
steel materials because of high strength and stiffness, lightweight,
rapid manufacturing, and dynamic performance. Also, this study was
to develop or improve the seismic performance or seismic retrofit of
critical structures subjected to strong ground motions and earthquake
aftershocks, by utilizing GFRP-Corrugated Infill Panels (GCIP).
Abstract: The first part of the paper analyzes the dynamics of
the total fertility rate both at the national and regional level, pointing
out the regional disparities in the distribution of this indicator. At the
same time, we also focus on the collapse of the number of live births,
on the changes in the fertility rate by birth rank, as well as on the
failure of acquiring the desired number of children. The second part
of the study centres upon a survey applied to urban families with 3
and more than 3 offspring. The preliminary analysis highlights the
fact that an increased fertility (more than 3rd rank) is triggered by the
parents’ above the average material condition and superior education.
The current situation of Romania, which is still passing through a
period of relatively rapid demographic changes, marked by numerous
convulsions, requires a new approach, in compliance with the recent
interpretations appropriate to a new post-transitional demographic
regime.
Abstract: We proposed a Hyperbolic Gompertz Growth Model
(HGGM), which was developed by introducing a shape parameter
(allometric). This was achieved by convoluting hyperbolic sine
function on the intrinsic rate of growth in the classical gompertz
growth equation. The resulting integral solution obtained
deterministically was reprogrammed into a statistical model and used
in modeling the height and diameter of Pines (Pinus caribaea). Its
ability in model prediction was compared with the classical gompertz
growth model, an approach which mimicked the natural variability of
height/diameter increment with respect to age and therefore provides
a more realistic height/diameter predictions using goodness of fit
tests and model selection criteria. The Kolmogorov Smirnov test and
Shapiro-Wilk test was also used to test the compliance of the error
term to normality assumptions while the independence of the error
term was confirmed using the runs test. The mean function of top
height/Dbh over age using the two models under study predicted
closely the observed values of top height/Dbh in the hyperbolic
gompertz growth models better than the source model (classical
gompertz growth model) while the results of R2, Adj. R2, MSE and
AIC confirmed the predictive power of the Hyperbolic Gompertz
growth models over its source model.
Abstract: A numerical model has been developed to investigate the thermally triggered release kinetics for drug delivery using phase change material as shell of microcapsules. Biocompatible material n-Eicosane is used as demonstration. PCM shell of microcapsule will remain in solid form after the drug is taken, so the drug will be encapsulated by the shell, and will not be released until the target body part of lesion is exposed to external heat source, which will thermally trigger the release kinetics, leading to solid-to-liquid phase change. The findings can lead to better understanding on the key effects influencing the phase change process for drug delivery applications. The facile approach to release drug from core/shell structure of microcapsule can be well integrated with organic solvent free fabrication of microcapsules, using double emulsion as template in microfluidic aqueous two phase system.