Abstract: This paper discusses the novel graphical approach for
stability analysis of multi induction motor drive controlled by a single
inverter. Stability issue arises in parallel connected induction motors
under unbalanced load conditions. The two powerful globally
accepted modeling and simulation software packages such as
MATLAB and LabVIEW are selected to perform the stability
analysis. The stability investigation is performed for different load
conditions and difference in stator and rotor resistances among the
two motors. It is very simple and effective than the techniques
presented to obtain the stability of the parallel connected induction
motor drive under unbalanced load conditions. Approximate transfer
functions are considered to model the induction motors, load
dynamics, speed controllers and inverter. Simulink library tools are
utilized to model the entire drive scheme in MATLAB. Stability
study is discussed in LabVIEW using control design and simulation
toolkits. Simulation results are illustrated for various running
conditions to demonstrate the effectiveness of the transfer function
method.
Abstract: This paper proposes a Particle Swarm Optimization
(PSO) based technique for the optimal allocation of Distributed
Generation (DG) units in the power systems. In this paper our aim is
to decide optimal number, type, size and location of DG units for
voltage profile improvement and power loss reduction in distribution
network. Two types of DGs are considered and the distribution load
flow is used to calculate exact loss. Load flow algorithm is combined
appropriately with PSO till access to acceptable results of this
operation. The suggested method is programmed under MATLAB
software. Test results indicate that PSO method can obtain better
results than the simple heuristic search method on the 30-bus and 33-
bus radial distribution systems. It can obtain maximum loss reduction
for each of two types of optimally placed multi-DGs. Moreover,
voltage profile improvement is achieved.
Abstract: This paper presents a conceptual model of agreement
options for negotiation support in multi-person decision on
optimizing high-rise building columns. The decision is complicated
since many parties involved in choosing a single alternative from a
set of solutions. There are different concern caused by differing
preferences, experiences, and background. Such building columns as
alternatives are referred to as agreement options which are
determined by identifying the possible decision maker group,
followed by determining the optimal solution for each group. The
group in this paper is based on three-decision makers preferences that
are designer, programmer, and construction manager. Decision
techniques applied to determine the relative value of the alternative
solutions for performing the function. Analytical Hierarchy Process
(AHP) was applied for decision process and game theory based agent
system for coalition formation. An n-person cooperative game is
represented by the set of all players. The proposed coalition
formation model enables each agent to select individually its allies or
coalition. It further emphasizes the importance of performance
evaluation in the design process and value-based decision.
Abstract: Innovations in technology have created new ethical
challenges. Essential use of electronic communication in the
workplace has escalated at an astronomical rate over the past decade.
As such, legal and ethical dilemmas confronted by both the employer
and the employee concerning managerial control and ownership of einformation
have increased dramatically in the USA. From the
employer-s perspective, ownership and control of all information
created for the workplace is an undeniable source of economic
advantage and must be monitored zealously. From the perspective of
the employee, individual rights, such as privacy, freedom of speech,
and freedom from unreasonable search and seizure, continue to be
stalwart legal guarantees that employers are not legally or ethically
entitled to abridge in the workplace. These issues have been the
source of great debate and the catalyst for legal reform. The fine line
between ethical and legal has been complicated by emerging
technologies. This manuscript will identify and discuss a number of
specific legal and ethical issues raised by the dynamic electronic
workplace and conclude with suggestions that employers should
follow to respect the delicate balance between employees- legal
rights to privacy and the employer's right to protect its knowledge
systems and infrastructure.
Abstract: Following the research in the Department of environmental engineering in Faculty of mechanical engineering on Technical University of Kosice and experiences with electrocoagulation style of disposal waste water, there were designed and partly examining the equipment of two stage revitalization on the standing and little fusible water of tenet electrolysis on the little tarns. With the cooperation with vet experts was that manners prove and it is innocuous for animals, during which time cyanobacteria are totally paralyzed. For the implementation of science and research results have been obtained by means EU funds for structural development.
Abstract: In this paper, we introduce an e-collaborative learning circles methodology which utilizes the information and communication technologies (ICTs) in e-educational processes. In e-collaborative learning circles methodology, the teachers and students announce their research projects on various mailing lists and discussion boards using available ICTs. The teachers & moderators and students who are already members of the e-forums, discuss the project proposals in their classrooms sent out by the potential global partner schools and return the requested feed back to the proposing school(s) about their level of the participation and contribution in the research. In general, an e-collaborative learning circle project is implemented with a small and diverse group (usually 8-10 participants) from around the world. The students meet regularly over a period of weeks/months through the ICTs during the ecollaborative learning process. When the project is completed, a project product (e-book / DVD) is prepared and sent to the circle members. In this research, when taking into account the interests and motivation of the participating students with the facilitating role of the teacher(s), the students in each circle do research to obtain new data and information, thus enabling them to have the opportunity to meet both different cultures and international understandings across the globe. However, while the participants communicate along with the members in the circle they also practice and develop their communication language skills. Finally, teachers and students find the possibility to develop their skills in using the ICTs as well.
Abstract: In this paper, a alternative structure method for
continuous time sigma delta modulator is presented. In this
modulator for implementation of integrators in loop filter second
generation current conveyors are employed. The modulator is
designed in CMOS technology and features low power consumption
(65db),
and with 180khZ bandwidth. Simulation results confirm that this
design is suitable for data converters.
Abstract: The purpose of this study was to present a reliable mean for human-computer interfacing based on finger gestures made in two dimensions, which could be interpreted and adequately used in controlling a remote robot's movement. The gestures were captured and interpreted using an algorithm based on trigonometric functions, in calculating the angular displacement from one point of touch to another as the user-s finger moved within a time interval; thereby allowing for pattern spotting of the captured gesture. In this paper the design and implementation of such a gesture based user interface was presented, utilizing the aforementioned algorithm. These techniques were then used to control a remote mobile robot's movement. A resistive touch screen was selected as the gesture sensor, then utilizing a programmed microcontroller to interpret them respectively.
Abstract: The design of technological procedures for
manufacturing certain products demands the definition and
optimization of technological process parameters. Their
determination depends on the model of the process itself and its
complexity. Certain processes do not have an adequate mathematical
model, thus they are modeled using heuristic methods. First part of
this paper presents a state of the art of using soft computing
techniques in manufacturing processes from the perspective of
applicability in modern CAx systems. Methods of artificial
intelligence which can be used for this purpose are analyzed. The
second part of this paper shows some of the developed models of
certain processes, as well as their applicability in the actual
calculation of parameters of some technological processes within the
design system from the viewpoint of productivity.
Abstract: The pipe inspection operation is the difficult detective
performance. Almost applications are mainly relies on a manual
recognition of defective areas that have carried out detection by an
engineer. Therefore, an automation process task becomes a necessary
in order to avoid the cost incurred in such a manual process. An
automated monitoring method to obtain a complete picture of the
sewer condition is proposed in this work. The focus of the research is
the automated identification and classification of discontinuities in
the internal surface of the pipe. The methodology consists of several
processing stages including image segmentation into the potential
defect regions and geometrical characteristic features. Automatic
recognition and classification of pipe defects are carried out by means
of using an artificial neural network technique (ANN) based on
Radial Basic Function (RBF). Experiments in a realistic environment
have been conducted and results are presented.
Abstract: The design of a pattern classifier includes an attempt
to select, among a set of possible features, a minimum subset of
weakly correlated features that better discriminate the pattern classes.
This is usually a difficult task in practice, normally requiring the
application of heuristic knowledge about the specific problem
domain. The selection and quality of the features representing each
pattern have a considerable bearing on the success of subsequent
pattern classification. Feature extraction is the process of deriving
new features from the original features in order to reduce the cost of
feature measurement, increase classifier efficiency, and allow higher
classification accuracy. Many current feature extraction techniques
involve linear transformations of the original pattern vectors to new
vectors of lower dimensionality. While this is useful for data
visualization and increasing classification efficiency, it does not
necessarily reduce the number of features that must be measured
since each new feature may be a linear combination of all of the
features in the original pattern vector. In this paper a new approach is
presented to feature extraction in which feature selection, feature
extraction, and classifier training are performed simultaneously using
a genetic algorithm. In this approach each feature value is first
normalized by a linear equation, then scaled by the associated weight
prior to training, testing, and classification. A knn classifier is used to
evaluate each set of feature weights. The genetic algorithm optimizes
a vector of feature weights, which are used to scale the individual
features in the original pattern vectors in either a linear or a nonlinear
fashion. By this approach, the number of features used in classifying
can be finely reduced.
Abstract: In this study, a nickel film with nano-crystalline grains,
high hardness and smooth surface was electrodeposited using a post
supercritical carbon dioxide (CO2) mixed Watts electrolyte. Although
the hardness was not as high as its Sc-CO2 counterpart, the thin coating
contained significantly less number of nano-sized pinholes. By
measuring the escape concentration of the dissolved CO2 in post
Sc-CO2 mixed electrolyte with the elapsed time, it was believed that
the residue of dissolved CO2 bubbles should closely relate to the
improvement in hardness and surface roughness over its conventional
plating counterpart. Therefore, shortening the duration of
electroplating with the raise of current density up to 0.5 A/cm2 could
effectively retain more post Sc-CO2 mixing effect. This study not only
confirms the roles of dissolved CO2 bubbles in electrolyte but also
provides a potential process to overcome most issues associated with
the cost in building high-pressure chamber for large size products and
continuous plating using supercritical method.
Abstract: In the traditional architecture, buildings were designed
to achieve human comfort by using locally available building materials and construction technology which were more responsive to
their climatic and geographic condition. This paper will try to bring out the wisdom of the local masons and builders, often the inhabitants
themselves, about their way of living, and shaping their built environment, indoor and outdoor spaces, as a response to the local
climatic conditions, from the findings of a field
settlement.
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: The intention of this paper is, to help the user of evolutionary algorithms to adapt them easier to their problem at hand. For a lot of problems in the technical field it is not necessary to reach an optimum solution, but to reach a good solution in time. In many cases the solution is undetermined or there doesn-t exist a method to determine the solution. For these cases an evolutionary algorithm can be useful. This paper intents to give the user rules of thumb with which it is easier to decide if the problem is suitable for an evolutionary algorithm and how to design them.
Abstract: The special and unique advantages of explosive
forming, has developed its use in different industries. Considering the
important influence of improving the current explosive forming
techniques on increasing the efficiency and control over the
explosive forming procedure, the effects of air and water as the
energy-conveying medium, and also their differences will be
illustrated in this paper. Hence, a large number of explosive forming
tests have been conducted on two sizes of thin walled cylindrical
shells by using air and water as the working medium. Comparative
diagrams of the maximum radial deflection of work-pieces of the
same size, as a function of the scaled distance, show that for the
points with the same values of scaled distance, the maximum radial
deformation caused by the under water explosive loading is 4 to 5
times more than the deflection of the shells under explosive forming,
while using air. Results of this experimental research have also been
compared with other studies which show that using water as the
energy conveying media increases the efficiency up to 4.8 times. The
effect of the media on failure modes of the shells, and the necking
mechanism of the walls of the specimens, while being explosively
loaded, are also discussed in this issue. Measuring the tested
specimens shows that, the increase in the internal volume has been
accompanied by necking of the walls, which finally results in the
radial rupture of the structure.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: Using efficient classification methods is necessary for automatic fingerprint recognition system. This paper introduces a new structural approach to fingerprint classification by using the directional image of fingerprints to increase the number of subclasses. In this method, the directional image of fingerprints is segmented into regions consisting of pixels with the same direction. Afterwards the relational graph to the segmented image is constructed and according to it, the super graph including prominent information of this graph is formed. Ultimately we apply a matching technique to compare obtained graph with the model graphs in order to classify fingerprints by using cost function. Increasing the number of subclasses with acceptable accuracy in classification and faster processing in fingerprints recognition, makes this system superior.
Abstract: The remote diagnosis and remote medical smoked to
part. In China, in accordance with the requirements of different
applications of remote diagnosis and Relates to the technical
difference, which can be divided into special purpose remote diagnosis
and treatment system, the remote will Referral system, remote medical
consultation system, remote rehabilitation technology and remote
operation technology. In this article, will introduce China for the
special purpose of service remote diagnosis and treatment system and
technology, including: China disabled status and virtual reality
technology; China 's domestic family medical care system and China 's
current situation of the development of telemedicine.
Abstract: Rational Emotive Behaviour Therapy is the first
cognitive behavior therapy which was introduced by Albert Ellis.
This is a systematic and structured psychotherapy which is effective
in treating various psychological problems. A patient, 25 years old
male, experienced intense fear and situational panic attack to return
to his faculty and to face his class-mates after a long absence (2
years). This social anxiety disorder was a major factor that impeded
the progress of his study. He was treated with the use of behavioural
technique such as relaxation breathing technique and cognitive
techniques such as imagery, cognitive restructuring, rationalization
technique and systematic desensitization. The patient reported
positive improvement in the anxiety disorder, able to progress well in
studies and lead a better quality of life as a student.