Abstract: This paper presents two types of microstrip bandpass
filter (BPF) at microwave frequencies. The first one is a tunable BPF
using planar patch resonators based on a varactor diode. The filter is
formed by a triple mode circular patch resonator with two pairs of
slots, in which the varactor diodes are connected. Indeed, this filter is
initially centered at 2.4 GHz; the center frequency of the tunable
patch filter could be tuned up to 1.8 GHz simultaneously with the
bandwidth, reaching high tuning ranges. Lossless simulations were
compared to those considering the substrate dielectric, conductor
losses and the equivalent electrical circuit model of the tuning
element in order to assess their effects. Within these variations,
simulation results showed insertion loss better than 2 dB and return
loss better than 10 dB over the passband. The second structure is a
BPF for ultra-wideband (UWB) applications based on multiple-mode
resonator (MMR) and rectangular-shaped defected ground structure
(DGS). This filter, which is compact size of 25.2 x 3.8 mm2, provides
in the pass band an insertion loss of 0.57 dB and a return loss greater
than 12 dB. The proposed filters presents good performances and the
simulation results are in satisfactory agreement with the
experimentation ones reported elsewhere.
Abstract: This study investigates the cleaning performance of
high intensity 360 kHz frequency on removal of nano-dimensional
and sub-micron particles from various surfaces, uniformity of the
cleaning tank and run to run variation of cleaning process. The
uniformity of the cleaning tank was measured by two different
methods i.e. 1. ppbTM meter and 2. Liquid Particle Counting (LPC)
technique. The result indicates that the energy was distributed more
uniformly throughout the entire cleaning vessel even at the corners
and edges of the tank when megasonic sweeping technology is
applied. The result also shows that rinsing the parts with 360 kHz
frequency at final rinse gives lower particle counts, hence higher
cleaning efficiency as compared to other frequencies. When
megasonic sweeping technology is applied each piezoelectric
transducers will operate at their optimum resonant frequency and
generates stronger acoustic cavitational force and higher acoustic
streaming velocity. These combined forces are helping to enhance the
particle removal and at the same time improve the overall cleaning
performance. The multiple extractions study was also carried out for
various frequencies to measure the cleaning potential and asymptote
value.
Abstract: For centuries humans have used the antimicrobial
properties of copper to their advantage. Yet, after all these years the
underlying mechanisms of copper mediated cell death in various
microbes remain unclear. We had explored the hypothesis that copper
mediated increased levels of lipid peroxidation in the membrane fatty
acids is responsible for increased killing in Escherichia coli. In this
study we show that in both gram positive (Staphylococcus aureus)
and gram negative (Pseudomonas aeruginosa) bacteria there is a
strong correlation between copper mediated cell death and increased
levels of lipid peroxidation. Interestingly, the non-spore forming
gram positive bacteria as well as gram negative bacteria show similar
patterns of cell death, increased levels of lipid peroxidation, as well
as genomic DNA degradation, however there is some difference in
loss in membrane integrity upon exposure to copper alloy surface.
Abstract: The management of Helicobacter pylori (H. pylori)
eradication is still a matter of discussion, full effectiveness is rarely
achieved, and it has many adverse effects. The use of probiotics may
be associated with better eradication rates and possibly prevention of
adverse events due to antibiotic therapy. The present clinical study
was undertaken to evaluate the efficacy of a specially designed
fermented milk product, containing Bifidobacterium lactis B420, on
the eradication of H. pylori infection in a prospective, randomized,
double-blind, controlled study in humans. Four test fermented milks
(FM) were specially designed in which counts of viable cells in all
products were 10^10 Log CFU. 100 mL-1 for Bifidobacterium lactis -
Bifidobacterium species 420. 190 subjects infected with H. pylori,
with previous diagnosis of functional dyspepsia according to Rome
III criteria entered the study. Bifidobacterium lactis B420,
administered twice a day for 90 days was not able to eradicate H.
pylori in Brazilian patients with functional dyspepsia.
Abstract: Artificial intelligence applications are commonly used
in industry in many fields in parallel with the developments in the
computer technology. In this study, a fire room was prepared for the
resistance of wooden construction elements and with the mechanism
here, the experiments of polished materials were carried out. By
utilizing from the experimental data, an artificial neural network
(ANN) was modelled in order to evaluate the final cross sections of
the wooden samples remaining from the fire. In modelling,
experimental data obtained from the fire room were used. In the
developed system, the first weight of samples (ws-gr), preliminary
cross-section (pcs-mm2), fire time (ft-minute), and fire temperature
(t-oC) as input parameters and final cross-section (fcs-mm2) as output
parameter were taken. When the results obtained from ANN and
experimental data are compared after making statistical analyses, the
data of two groups are determined to be coherent and seen to have no
meaning difference between them. As a result, it is seen that ANN
can be safely used in determining cross sections of wooden materials
after fire and it prevents many disadvantages.
Abstract: Sustainability and eco-friendly requirement of
engineering materials are sort for in recent times, thus giving rise to
the development of bio-composites. However, the natural fibres to
matrix interface interactions remain a key issue in getting the desired
mechanical properties from such composites. Treatment of natural
fibres is essential in improving matrix to filler adhesion, hence
improving its mechanical properties. In this study, investigations
were carried out to determine the effect of sodium hydroxide
treatment on the tensile, flexural, impact and hardness properties of
crushed and uncrushed Luffa cylindrica fibre reinforced recycled low
density polyethylene composites. The LC (Luffa cylindrica) fibres
were treated with 0%, 2%, 4%, 6%, 8% and 10% wt. sodium
hydroxide (NaOH) concentrations for a period of 24 hours under
room temperature conditions. A formulation ratio of 80/20 g (matrix
to reinforcement) was maintained for all developed samples. Analysis
of the results showed that the uncrushed luffa fibre samples gave
better mechanical properties compared with the crushed luffa fibre
samples. The uncrushed luffa fibre composites had a maximum
tensile and flexural strength of 7.65 MPa and 17.08 Mpa respectively
corresponding to a young modulus and flexural modulus of 21.08
MPa and 232.22 MPa for the 8% and 4% wt. NaOH concentration
respectively. Results obtained in the research showed that NaOH
treatment with the 8% NaOH concentration improved the mechanical
properties of the LC fibre reinforced composites when compared with
other NaOH treatment concentration values.
Abstract: This paper discusses the undesirable charge transfer
through the parasitic capacitances of the input transistors in a
multi-inputs voltage sense amplifier. Its intrinsic rail-to-rail voltage
transitions at the output nodes inevitably disturb the input sides
through the capacitive coupling between the outputs and inputs. Then,
it can possible degrade the stabilities of the reference voltage levels.
Moreover, it becomes more serious in multi-channel systems by
altering them for other channels, and so degrades the linearity of the
overall systems. In order to alleviate the internal node voltage
transition, the internal node stabilization techniques are proposed. It
achieves 45% and 40% improvements for node stabilization and input
referred disturbance, respectively.
Abstract: The planning of geological survey works is an
iterative process which involves planner, geologist, civil engineer and
other stakeholders, who perform different roles and have different
points of view. Traditionally, the team used paper maps or CAD
drawings to present the proposal which is not an efficient way to
present and share idea on the site investigation proposal such as
sitting of borehole location or seismic survey lines. This paper
focuses on how a GIS approach can be utilised to develop a webbased
system to support decision making process in the planning of
geological survey works and also to plan site activities carried out by
Singapore Geological Office (SGO). The authors design a framework
of building an interactive web-based GIS system, and develop a
prototype, which enables the users to obtain rapidly existing
geological information and also to plan interactively borehole
locations and seismic survey lines via a web browser. This prototype
system is used daily by SGO and has shown to be effective in
increasing efficiency and productivity as the time taken in the
planning of geological survey works is shortened. The prototype
system has been developed using the ESRI ArcGIS API 3.7 for Flex
which is based on the ArcGIS 10.2.1 platform.
Abstract: The research studies the behaviors based on
sufficiency economy philosophy at individual and community
levelsas well as the satisfaction of the urban community leaders by
collecting data with purposive sampling technique. For in-depth
interviews with 26 urban community leaders, the result shows that
the urban community leaders have good knowledge and
understanding about sufficiency economy philosophy. Especially in
terms of money spending, they must consider the need for living and
be economical. The activities in the community or society should not
take advantage of the others as well as colleagues. At present, most of
the urban community leaders live in sufficient way. They often spend
time with public service, but many families are dealing with debt.
Many communities have some political conflict and high family
allowances because of living in the urban communities with rapid
social and economic changes. However, there are many communities
that leaders have applied their wisdom in development for their
people by gathering and grouping the professionals to form activities
such as making chilli sauce, textile organization, making artificial
flowers to worship the sanctity. The most prominent group is the foot
massage business in Wat Pracha Rabue Tham. This professional
group is supported continuously by the government. One of the
factors in terms of satisfaction used for evaluating community leaders
is the customary administration in brotherly, interdependent way
rather than using the absolute power or controlling power, but using
the roles of leader to perform the activities with their people intently,
determinedly and having public mind for people.
Abstract: This paper describes the tradeoffs and the design from
scratch of a self-contained, easy-to-use health dashboard software
system that provides customizable data tracking for patients in smart
homes. The system is made up of different software modules and
comprises a front-end and a back-end component. Built with HTML,
CSS, and JavaScript, the front-end allows adding users, logging into
the system, selecting metrics, and specifying health goals. The backend
consists of a NoSQL Mongo database, a Python script, and a
SimpleHTTPServer written in Python. The database stores user
profiles and health data in JSON format. The Python script makes use
of the PyMongo driver library to query the database and displays
formatted data as a daily snapshot of user health metrics against
target goals. Any number of standard and custom metrics can be
added to the system, and corresponding health data can be fed
automatically, via sensor APIs or manually, as text or picture data
files. A real-time METAR request API permits correlating weather
data with patient health, and an advanced query system is
implemented to allow trend analysis of selected health metrics over
custom time intervals. Available on the GitHub repository system,
the project is free to use for academic purposes of learning and
experimenting, or practical purposes by building on it.
Abstract: Non-linear FEM calculations are indispensable when
important technical information like operating performance of a
rubber component is desired. For example rubber bumpers built into
air-spring structures may undergo large deformations under load,
which in itself shows non-linear behavior. The changing contact
range between the parts and the incompressibility of the rubber
increases this non-linear behavior further. The material
characterization of an elastomeric component is also a demanding
engineering task.
The shape optimization problem of rubber parts led to the study of
FEM based calculation processes. This type of problems was posed
and investigated by several authors. In this paper the time demand of
certain calculation methods are studied and the possibilities of time
reduction is presented.
Abstract: Composite material based on Fe3Si micro-particles
and Mn-Zn nano-ferrite was prepared using powder metallurgy
technology. The sol-gel followed by autocombustion process was
used for synthesis of Mn0.8Zn0.2Fe2O4 ferrite. 3 wt.% of mechanically
milled ferrite was mixed with Fe3Si powder alloy. Mixed micro-nano
powder system was homogenized by the Resonant Acoustic Mixing
using ResodynLabRAM Mixer. This non-invasive homogenization
technique was used to preserve spherical morphology of Fe3Si
powder particles. Uniaxial cold pressing in the closed die at pressure
600 MPa was applied to obtain a compact sample. Microwave
sintering of green compact was realized at 800°C, 20 minutes, in air.
Density of the powders and composite was measured by
Hepycnometry. Impulse excitation method was used to measure
elastic properties of sintered composite. Mechanical properties were
evaluated by measurement of transverse rupture strength (TRS) and
Vickers hardness (HV). Resistivity was measured by 4 point probe
method. Ferrite phase distribution in volume of the composite was
documented by metallographic analysis.
It has been found that nano-ferrite particle distributed among
micro- particles of Fe3Si powder alloy led to high relative density
(~93%) and suitable mechanical properties (TRS >100 MPa, HV
~1GPa, E-modulus ~140 GPa) of the composite. High electric
resistivity (R~6.7 ohm.cm) of prepared composite indicate their
potential application as soft magnetic material at medium and high
frequencies.
Abstract: Since, it is essential to provide homeless people by the
earthquake with safe, habitable accommodation repairing medium
and slight levels of damage at the connection parts should be
undertaken. In order to prove that a repaired connection was
sufficiently strong, a precast beam to column post tensioned
connection was tested in three phases. In phase one, the middle level
damage was observed at 6% drift at these connections. As a result of
the extra loads applied, little damage was observed. In the last phase,
the four connections tested in the first phase were repaired using
epoxy resin and then retested. The results from the tests on the
repaired precast and the undamaged specimens showed that the
repaired specimens were sufficiently strong, thus proving that repair
to damaged precast beam to column post tensioned connections can
be undertaken.
Abstract: Various personality profile tests are used to identify
personality strengths and limits in individuals, helping both
individuals and managers to optimize work and team effort in
organizations. One such test, the Hartman’s personality profile,
emphasizes four driving "core motives" influenced or affected by
both strengths and limitations classified into four colors: Red -
motivated by power; Blue - discipline and loyalty; White - peace; and
Yellow – fun loving. Two shortcomings of Hartman’s personality test
are noted; 1) only one selection for every item / situation allowed and
2) selection of an item / option even if not applicable. A test taker
may be as much nurturing as he is opinionated but since
“opinionated” seems less attractive the individual would likely select
nurturing, causing a misidentification in personality strengths and
limits. Since few individuals have a “strong” personality, it is
difficult to assess their true personality strengths and limits allowing
only one choice or requiring unwanted choices, undermining the
potential of the test. We modified Hartman’s personality profile
allowing test takers to make either multiple choices for any item /
situation or leave them blank if applicable. Sixty-eight participants
(38 males and 30 females), 17 - 49 years old, from countries in Asia,
Europe, N. America, CIS, Africa, Latin America, and Oceania were
included. 58 participants (85.3%) reported the modified test, allowing
multiple / no choices better identified their personality strengths and
limits, while 10 participants (14.7%) expressed the original (one
choice version) was sufficient. The overall results show that our
modified test enhanced the identification and balance of core
personalities’ strengths and limits, aiding test takers, managers and
organizations to better assess individual characteristics, particularly
useful in making task-related, teamwork, and management decisions.
Abstract: The aim of this study was to select the best strains of
Saccharomyces cerevisiae able to resist lead and cadmium. Ten
strains were screened on the basis of their resistance at different
concentrations of 0, 2, 4, 8, 12, 16, 20 and 24 ppm for Pb and 0, 0.5,
1, 2, 4, 6, 8 and 10 ppm for Cd. The properties of baker's yeast
quality were decreased by the increase of Pb or Cd in growth
medium. The slope values of yield, total viable cells and gassing
power of produced baker's yeast were investigated as an indicator of
metal resistant. In addition, concentrations of Pb and Cd in produced
baker's yeast were determined. The strain of S. cerevisiae FH-620
had the highest resistance against Pb and Cd and had the minimum
levels of both two investigated metals in produced baker's yeast.
Abstract: Microbial fuel cells (MFCs) represent a promising
technology for simultaneous bioelectricity generation and wastewater
treatment. Catalysts are significant portions of the cost of microbial
fuel cell cathodes. Many materials have been tested as aqueous
cathodes, but air-cathodes are needed to avoid energy demands for
water aeration. The sluggish oxygen reduction reaction (ORR) rate at
air cathode necessitates efficient electrocatalyst such as carbon
supported platinum catalyst (Pt/C) which is very costly. Manganese
oxide (MnO2) was a representative metal oxide which has been
studied as a promising alternative electrocatalyst for ORR and has
been tested in air-cathode MFCs. However the single MnO2 has poor
electric conductivity and low stability. In the present work, the MnO2
catalyst has been modified by doping Pt nanoparticle. The goal of the
work was to improve the performance of the MFC with minimum Pt
loading. MnO2 and Pt nanoparticles were prepared by hydrothermal
and sol gel methods, respectively. Wet impregnation method was
used to synthesize Pt/MnO2 catalyst. The catalysts were further used
as cathode catalysts in air-cathode cubic MFCs, in which anaerobic
sludge was inoculated as biocatalysts and palm oil mill effluent
(POME) was used as the substrate in the anode chamber. The asprepared
Pt/MnO2 was characterized comprehensively through field
emission scanning electron microscope (FESEM), X-Ray diffraction
(XRD), X-ray photoelectron spectroscopy (XPS), and cyclic
voltammetry (CV) where its surface morphology, crystallinity,
oxidation state and electrochemical activity were examined,
respectively. XPS revealed Mn (IV) oxidation state and Pt (0)
nanoparticle metal, indicating the presence of MnO2 and Pt.
Morphology of Pt/MnO2 observed from FESEM shows that the
doping of Pt did not cause change in needle-like shape of MnO2
which provides large contacting surface area. The electrochemical
active area of the Pt/MnO2 catalysts has been increased from 276 to
617 m2/g with the increase in Pt loading from 0.2 to 0.8 wt%. The
CV results in O2 saturated neutral Na2SO4 solution showed that
MnO2 and Pt/MnO2 catalysts could catalyze ORR with different
catalytic activities. MFC with Pt/MnO2 (0.4 wt% Pt) as air cathode
catalyst generates a maximum power density of 165 mW/m3, which
is higher than that of MFC with MnO2 catalyst (95 mW/m3). The
open circuit voltage (OCV) of the MFC operated with MnO2 cathode
gradually decreased during 14 days of operation, whereas the MFC
with Pt/MnO2 cathode remained almost constant throughout the
operation suggesting the higher stability of the Pt/MnO2 catalyst.
Therefore, Pt/MnO2 with 0.4 wt% Pt successfully demonstrated as an
efficient and low cost electrocatalyst for ORR in air cathode MFC with higher electrochemical activity, stability and hence enhanced
performance.
Abstract: In this paper, we propose an automatic verification
technology of software patches for user virtual environments on IaaS
Cloud to decrease verification costs of patches. In these days, IaaS
services have been spread and many users can customize virtual
machines on IaaS Cloud like their own private servers. Regarding to
software patches of OS or middleware installed on virtual machines,
users need to adopt and verify these patches by themselves. This task
increases operation costs of users. Our proposed method replicates
user virtual environments, extracts verification test cases for user
virtual environments from test case DB, distributes patches to virtual
machines on replicated environments and conducts those test cases
automatically on replicated environments. We have implemented the
proposed method on OpenStack using Jenkins and confirmed the
feasibility. Using the implementation, we confirmed the effectiveness
of test case creation efforts by our proposed idea of 2-tier abstraction
of software functions and test cases. We also evaluated the automatic
verification performance of environment replications, test cases
extractions and test cases conductions.
Abstract: The web’s increased popularity has included a huge
amount of information, due to which automated web page
classification systems are essential to improve search engines’
performance. Web pages have many features like HTML or XML
tags, hyperlinks, URLs and text contents which can be considered
during an automated classification process. It is known that Webpage
classification is enhanced by hyperlinks as it reflects Web page
linkages. The aim of this study is to reduce the number of features to
be used to improve the accuracy of the classification of web pages. In
this paper, a novel feature selection method using an improved
Particle Swarm Optimization (PSO) using principle of evolution is
proposed. The extracted features were tested on the WebKB dataset
using a parallel Neural Network to reduce the computational cost.
Abstract: The main aim of this research was to investigate a
prototype bamboo shading device. There were two objectives to this
study: first, to investigate the effects of non-chemical treatments on
bamboo shading devices damaged by powder-post beetles and fungi,
and second to develop a prototype bamboo shading device. This
study of the effects of non-chemical treatments on bamboo shading
devices damage by powder-post beetles in the laboratory showed
that, among seven treatments tested, wood vinegar treatment can
protect powder-post beetles better than the original method by up to
92.91%. It was also found that wood vinegar treatment shows the
best performance in fungi protection and works better than the
original method by up to 40%. A second experiment was carried out
by constructing four bamboo shading devices and installing them on
a building for 28 days. All aspects of shading device were
investigated in terms of their beauty, durability, and ease of
construction and assembly. The final prototype was developed from
the lessons learned from the test results. In conclusion, this study
showed the effectiveness of some natural preservatives against insect
and fungi damage, and it also illustrated the characteristics of a
prototype bamboo shading device that can be constructed by rural
workers within one week.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.