Abstract: Within the framework of a method of the information
theory it is offered statistics and probabilistic model for definition of
cause-and-effect relations in the coupled multicomponent
subsystems. The quantitative parameter which is defined through
conditional and unconditional entropy functions is introduced. The
method is applied to the analysis of the experimental data on
dynamics of change of the chemical elements composition of plants
organs (roots, reproductive organs, leafs and stems). Experiment is
directed on studying of temporal processes of primary soil formation
and their connection with redistribution dynamics of chemical
elements in plant organs. This statistics and probabilistic model
allows also quantitatively and unambiguously to specify the
directions of the information streams on plant organs.
Abstract: Highly ordered arrays of TiO2 nanotubes (TiNTs) were grown vertically on Ti foil by electrochemical anodization. We controlled the lengths of these TiNTs from 2.4 to 26.8 ¶üÇóμm while varying the water contents (1, 3, and 6 wt%) of the electrolyte in ethylene glycol in the presence of 0.5 wt% NH4F with anodization for various applied voltages (20–80 V), periods (10–240 min) and temperatures (10–30 oC). For vertically aligned TiNT arrays, not only the increase in their tube lengths, but also their geometric (wall thickness and surface roughness) and crystalline structure lead to a significant influence on photocatalytic activity. The length optimization for methylene blue (MB) photodegradation was 18 μm. Further extending the TiNT length yielded lower photocatalytic activity presumably related to the limited MB diffusion and light-penetration depth into the TiNT arrays. The results indicated that a maximum MB photodegradation rate was obtained for the discrete anatase TiO2 nanotubes with thick and rough walls.
Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: In this paper we present a new method for coin
identification. The proposed method adopts a hybrid scheme using
Eigenvalues of covariance matrix, Circular Hough Transform (CHT)
and Bresenham-s circle algorithm. The statistical and geometrical
properties of the small and large Eigenvalues of the covariance
matrix of a set of edge pixels over a connected region of support are
explored for the purpose of circular object detection. Sparse matrix
technique is used to perform CHT. Since sparse matrices squeeze
zero elements and contain only a small number of non-zero elements,
they provide an advantage of matrix storage space and computational
time. Neighborhood suppression scheme is used to find the valid
Hough peaks. The accurate position of the circumference pixels is
identified using Raster scan algorithm which uses geometrical
symmetry property. After finding circular objects, the proposed
method uses the texture on the surface of the coins called texton,
which are unique properties of coins, refers to the fundamental micro
structure in generic natural images. This method has been tested on
several real world images including coin and non-coin images. The
performance is also evaluated based on the noise withstanding
capability.
Abstract: Crystallization has been used for the separation of
chloronitrobenzene or CNBs, which are isomeric substances (o-, mand
p-CNB) and important intermediates in chemical productions. Effects of feed composition on the crystallization of m- and p-CNB was first studied. The results conform to the binary phase diagram of
m- and p-CNB. After that, effects of FAU zeolites (NaX, CaX, BaX, NaY and CaY) above the eutectic composition (63.5 and 65.0 wt% m-CNB in the feed) was also investigated. The results showed that
the FAU zeolites significantly affected the precipitates, the
composition of which was shifted from being rich in m-CNB to rich
in p-CNB. Effects of the number of FAU zeolites on the precipitate composition was then studied. The results revealed that the
precipitates from the lower number of the zeolites had higher p-CNB purity than those from the higher number of zeolite.
Abstract: This paper presents an integrated knowledge-based
approach to multi-scale modeling of aquatic systems, with a view to
enhancing predictive power and aiding environmental management
and policy-making. The basic phases of this approach have been
exemplified in the case of a bay in Saronicos Gulf (Attiki, Greece).
The results showed a significant problem with rising phytoplankton
blooms linked to excessive microbial growth, arisen mostly due to
increased nitrogen inflows; therefore, the nitrification/denitrification
processes of the benthic and water column sub-systems have
provided the quality variables to be monitored for assessing
environmental status. It is thereby demonstrated that the proposed
approach facilitates modeling choices and implementation option
decisions, while it provides substantial support for knowledge and
experience capitalization in long-term water management.
Abstract: Team distillation assisted by microwave extraction
(SDAM) considered as accelerated technique extraction is a
combination of microwave heating and steam distillation, performed
at atmospheric pressure. SDAM has been compared with the same
technique coupled with the cryogrinding of seeds (SDAM -CG).
Isolation and concentration of volatile compounds are performed by a
single stage for the extraction of essential oil from Cuminum
cyminum seeds. The essential oils extracted by these two methods for
5 min were quantitatively (yield) and qualitatively (aromatic profile)
no similar. These methods yield an essential oil with higher amounts
of more valuable oxygenated compounds, and allow substantial
savings of costs, in terms of time, energy and plant material. SDAM
and SDAM-CG is a green technology and appears as a good
alternative for the extraction of essential oils from aromatic plants.
Abstract: This paper proposes a technique to protect against
email bombing. The technique employs a statistical approach, Naïve
Bayes (NB), and Neural Networks to show that it is possible to
differentiate between good and bad traffic to protect against email
bombing attacks. Neural networks and Naïve Bayes can be trained
by utilizing many email messages that include both input and output
data for legitimate and non-legitimate emails. The input to the model
includes the contents of the body of the messages, the subject, and
the headers. This information will be used to determine if the email
is normal or an attack email. Preliminary tests suggest that Naïve
Bayes can be trained to produce an accurate response to confirm
which email represents an attack.
Abstract: Impinging jets are widely used in industrial cooling
systems for their high heat transfer characteristics at stagnation points.
However, the heat transfer characteristics are low in the downstream
direction. In order to improve the heat transfer coefficient further
downstream, investigations introducing ribs on jet-cooled flat plates
have been conducted. Most studies regarding the heat-transfer
enhancement using a rib-roughened wall have dealt with the rib pitch.
In this paper, we focused on the rib spacing and demonstrated that the
rib spacing must be more than 6 times the nozzle width to improve heat
transfer at Reynolds number Re=5.0×103 because it is necessary to
have enough space to allow reattachment of flow behind the first rib.
Abstract: In this study, we developed a model to predict the
temperature and the pressure variation in an internal combustion
engine operated in HCCI (Homogeneous charge compression ignition)
mode. HCCI operation begins from aspirating of homogeneous charge
mixture through intake valve like SI (Spark ignition) engine and the
premixed charge is compressed until temperature and pressure of
mixture reach autoignition point like diesel engine. Combustion phase
was described by double-Wiebe function. The single zone model
coupled with an double-Wiebe function were performed to simulated
pressure and temperature between the period of IVC (Inlet valve close)
and EVO (Exhaust valve open). Mixture gas properties were
implemented using STANJAN and transfer the results to main model.
The model has considered the engine geometry and enables varying in
fuelling, equivalence ratio, manifold temperature and pressure. The
results were compared with the experiment and showed good
correlation with respect to combustion phasing, pressure rise, peak
pressure and temperature. This model could be adapted and use to
control start of combustion for HCCI engine.
Abstract: This paper study about using of nonparametric
models for Gross National Product data in Turkey and Stanford heart
transplant data. It is discussed two nonparametric techniques called
smoothing spline and kernel regression. The main goal is to compare
the techniques used for prediction of the nonparametric regression
models. According to the results of numerical studies, it is concluded
that smoothing spline regression estimators are better than those of
the kernel regression.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Thailand is the agriculture country as the weather and geography are suitable for agriculture environment. In 2011, the quantity of exported fresh vegetable was 126,069 tons which valued 117.1 million US dollars. Although the fresh vegetable has a high potential in exporting, there also have a lack of knowledge such as chemical usage, land usage, marketing and also the transportation and logistics. Nakorn Pathom province is the area which the farmer and manufacturer of fresh vegetable located. The objectives of this study are to study the basic information of the local fresh vegetable farmers in Nakorn Pathom province, to study the factor which effects the management of the fresh vegetable supply chain in Nakorn Pathom province and to study the problems and obstacle of the fresh vegetable supply chain in Nakorn Pathom province. This study is limited to the flow of the Nakorn Pathom province fresh vegetable from the farmers to the country which import the vegetable from Thailand. The populations of this study are 100 local farmers in Nakorn Pathom province. The result of this study shows that the key process of the fresh vegetable supply chain is in the supply sourcing process and manufacturing process.
Abstract: We present a white LED-based optical wireless
communication systems for indoor ubiquitous sensor networks. Each
sensor node could access to the server through the PLC (Power Line
Communication)-Ethernet interface. The proposed system offers a
full-duplex wireless link by using different wavelengths to reduce the
inter-symbol interference between uplink and downlink. Through the
1-to-n optical wireless sensor network and PLC modem, the mobile
terminals send a temperature data to server. The data transmission
speed and distance are 115.2kbps and about 60cm, respectively.
Abstract: An adaptive Helmholtz resonator was designed and
adapted to hydraulics. The resonator was controlled by open- and
closed-loop controls so that 20 dB attenuation of the peak-to-peak
value of the pulsating pressure was maintained. The closed-loop
control was noted to be better, albeit it was slower because of its low
pressure and temperature variation, which caused variation in the
effective bulk modulus of the hydraulic system. Low-pressure
hydraulics contains air, which affects the stiffness of the hydraulics,
and temperature variation changes the viscosity of the oil. Thus, an
open-loop control loses its efficiency if a condition such as
temperature or the amount of air changes after calibration. The
instability of the low-pressure hydraulic system reduced the
operational frequency range of the Helmholtz resonator when
compared with the results of an analytical model.
Different dampers for hydraulics are presented. Then analytical
models of a hydraulic pipe and a hydraulic pipe with a Helmholtz
resonator are presented. The analytical models are based on the wave
equation of sound pressure. Finally, control methods and the results
of experiments are presented.
Abstract: Hepatocellular carcinoma, also called hepatoma, most
commonly appears in a patient with chronic viral hepatitis. In
patients with a higher suspicion of HCC, such as small or subtle
rising of serum enzymes levels, the best method of diagnosis
involves a CT scan of the abdomen, but only at high cost. The aim of
this study was to increase the ability of the physician to early detect
HCC, using a probabilistic neural network-based approach, in order
to save time and hospital resources.
Abstract: Carbon nanotubes (CNTs) are attractive because of
their excellent chemical durability mechanical strength and electrical
properties. Therefore there is interest in CNTs for not only electrical
and mechanical application, but also biological and medical
application.
In this study, the dispersion power of surfactant-treated multiwalled
carbon nanotubes (MWCNTs) and their effect on the antibacterial
activity were examined. Surfactant was used sodium
dodecyl-benzenesulfonate (SDBS). UV-vis absorbance and
transmission electron microscopy(TEM) were used to characterize the
dispersion of MWCNTs in the aqueous phase, showing that the
surfactant molecules had been adsorbed onto the MWCNTs surface.
The surfactant-treated MWCNTs exhibited antimicrobial activities
to streptococcus mutans. The optical density growth curves and viable
cell number determined by the plating method suggested that the
antimicrobial activity of surfactant-treated MWCNTs was both
concentration and treatment time-dependent.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: Recently, the improvements in processing performance
of a computer and in high speed communication of an optical fiber
have been achieved, so that the amount of data which are processed
by a computer and flowed on a network has been increasing greatly.
However, in a client-server system, since the server receives and
processes the amount of data from the clients through the network, a
load on the server is increasing. Thus, there are needed to introduce
a server with high processing ability and to have a line with high
bandwidth. In this paper, concerning to P2P networks to resolve the
load on a specific server, a criterion called an Indexed-Priority Metric
is proposed and its performance is evaluated. The proposed metric is
to allocate some files to each node. As a result, the load on a specific
server can distribute them to each node equally well. A P2P file
sharing system using the proposed metric is implemented. Simulation
results show that the proposed metric can make it distribute files on
the specific server.
Abstract: When programming in languages such as C, Java, etc.,
it is difficult to reconstruct the programmer's ideas only from the
program code. This occurs mainly because, much of the programmer's
ideas behind the implementation are not recorded in the code during
implementation. For example, physical aspects of computation such as
spatial structures, activities, and meaning of variables are not required
as instructions to the computer and are often excluded. This makes the
future reconstruction of the original ideas difficult. AIDA, which is a
multimedia programming language based on the cyberFilm model, can
solve these problems allowing to describe ideas behind programs
using advanced annotation methods as a natural extension to
programming. In this paper, a development environment that
implements the AIDA language is presented with a focus on the
annotation methods. In particular, an actual scientific numerical
computation code is created and the effects of the annotation methods
are analyzed.