Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This research work proposed a study of fruit bruise detection by means of a biospeckle method, selecting the papaya fruit (Carica papaya) as testing body. Papaya is recognized as a fruit of outstanding nutritional qualities, showing high vitamin A content, calcium, carbohydrates, exhibiting high popularity all over the world, considering consumption and acceptability. The commercialization of papaya faces special problems which are associated to bruise generation during harvesting, packing and transportation. Papaya is classified as climacteric fruit, permitting to be harvested before the maturation is completed. However, by one side bruise generation is partially controlled once the fruit flesh exhibits high mechanical firmness. By the other side, mechanical loads can set a future bruise at that maturation stage, when it can not be detected yet by conventional methods. Mechanical damages of fruit skin leave an entrance door to microorganisms and pathogens, which will cause severe losses of quality attributes. Traditional techniques of fruit quality inspection include total soluble solids determination, mechanical firmness tests, visual inspections, which would hardly meet required conditions for a fully automated process. However, the pertinent literature reveals a new method named biospeckle which is based on the laser reflectance and interference phenomenon. The laser biospeckle or dynamic speckle is quantified by means of the Moment of Inertia, named after its mechanical counterpart due to similarity between the defining formulae. Biospeckle techniques are able to quantify biological activities of living tissues, which has been applied to seed viability analysis, vegetable senescence and similar topics. Since the biospeckle techniques can monitor tissue physiology, it could also detect changes in the fruit caused by mechanical damages. The proposed technique holds non invasive character, being able to generate numerical results consistent with an adequate automation. The experimental tests associated to this research work included the selection of papaya fruit at different maturation stages which were submitted to artificial mechanical bruising tests. Damages were visually compared with the frequency maps yielded by the biospeckle technique. Results were considered in close agreement.
Abstract: Internet Protocol version 4 (IPv4) address is decreasing and a rapid transition method to the next generation IP address (IPv6) should be established. This study aims to evaluate and select the best performance of the IPv6 address network transitionmechanisms, such as IPv4/IPv6 dual stack, transport Relay Translation (TRT) and Reverse Proxy with additional features. It is also aim to prove that faster access can be done while ensuring optimal usage of available resources used during the test and actual implementation. This study used two test methods such asInternet Control Message Protocol (ICMP)ping and ApacheBenchmark (AB) methodsto evaluate the performance.Performance metrics for this study include aspects ofaverageaccessin one second,time takenfor singleaccess,thedata transfer speed and the costof additional requirements.Reverse Proxy with Caching featureis the most efficientmechanism because of it simpler configurationandthe best performerfrom the test conducted.
Abstract: In this paper, we propose improved versions of DVHop
algorithm as QDV-Hop algorithm and UDV-Hop algorithm for
better localization without the need for additional range measurement
hardware. The proposed algorithm focuses on third step of DV-Hop,
first error terms from estimated distances between unknown node and
anchor nodes is separated and then minimized. In the QDV-Hop
algorithm, quadratic programming is used to minimize the error to
obtain better localization. However, quadratic programming requires
a special optimization tool box that increases computational
complexity. On the other hand, UDV-Hop algorithm achieves
localization accuracy similar to that of QDV-Hop by solving
unconstrained optimization problem that results in solving a system
of linear equations without much increase in computational
complexity. Simulation results show that the performance of our
proposed schemes (QDV-Hop and UDV-Hop) is superior to DV-Hop
and DV-Hop based algorithms in all considered scenarios.
Abstract: This paper attempts to highlight the significant role of
knowledge management practices (KMP) and competencies in
improving the performance and efficiency of public sector
organizations. It appears that public sector organizations in
developing countries have not received much attention in the
research literature of knowledge management and competencies.
Therefore, this paper seeks to explore the role of KMP and
competencies in achieving superior performance among public sector
organizations in Malaysia in the broader perspective. Survey
questionnaires were distributed to all Administrative and Diplomatic
Officers (ADS) from 28 ministries located in Putrajaya, Malaysia.
This paper also examines preliminary empirical results on the
relationship between support for knowledge management practices,
competencies, and orientation in Malaysia-s public organizations.
This paper supports the notion that the practices of knowledge
management at the organizational level are a prerequisite for
successful organizational performance. In conclusion, the results not
only have the potential to contribute theoretically to both
management strategy and knowledge management field literature but
also to the area of organizational performance.
Abstract: Geometric design is an important part of planning
process design for physical highway to fill up basic function of roads,
to give good traffic service. It is found that most of the road safety
problems occur at the horizontal curves and complex-compound
curves. In this paper, review on Sagarinn-Myinsain Portion of Nay
Pyi Taw - Mandalay highway has been conducted in aspect of
geometric design induced road safety condition. Horizontal
alignment of geometric features and curve details are reviewed based
on (AASHTO) standard and revised by Autodesk Land Desktop
Software. Moreover, 85th Percentile Operation Speeds (V85) with
driver confidence on horizontal curves is evaluated in order to obtain
the range of highway safety factor (FS). The length of the selected
highway portion is 13.65 miles and 8 lanes. The results of this study
can be used to investigate the possible hazardous locations in
advance and to revise how design radius and super elevation should
be for better road safety performance for the selected portion.
Moreover, the relationship between highway safety and highway
geometry characteristics can also be known.
Abstract: Locating the critical slip surface with the minimum factor of safety for a rock slope is a difficult problem. In recent years, some modern global optimization methods have been developed with success in treating various types of problems, but very few of such methods have been applied to rock mechanical problems. In this paper, use of hybrid model based on artificial immune system and cellular learning automata is proposed. The results show that the algorithm is an effective and efficient optimization method with a high level of confidence rate.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually to some extent the effects of blurred edges and jagged artifacts in the image. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to enhance edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (''jaggies'') along the tangent directions. In order to preserve image features such as edges, angles and textures, the nonlinear diffusion coefficients are locally adjusted according to the first and second order directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: The performance of sensor-less controlled induction
motor drive depends on the accuracy of the estimated speed.
Conventional estimation techniques being mathematically complex
require more execution time resulting in poor dynamic response. The
nonlinear mapping capability and powerful learning algorithms of
neural network provides a promising alternative for on-line speed
estimation. The on-line speed estimator requires the NN model to be
accurate, simpler in design, structurally compact and computationally
less complex to ensure faster execution and effective control in real
time implementation. This in turn to a large extent depends on the
type of Neural Architecture. This paper investigates three types of
neural architectures for on-line speed estimation and their
performance is compared in terms of accuracy, structural
compactness, computational complexity and execution time. The
suitable neural architecture for on-line speed estimation is identified
and the promising results obtained are presented.
Abstract: Investigation of soil properties like Cation Exchange
Capacity (CEC) plays important roles in study of environmental
reaserches as the spatial and temporal variability of this property
have been led to development of indirect methods in estimation of
this soil characteristic. Pedotransfer functions (PTFs) provide an
alternative by estimating soil parameters from more readily available
soil data. 70 soil samples were collected from different horizons of
15 soil profiles located in the Ziaran region, Qazvin province, Iran.
Then, multivariate regression and neural network model (feedforward
back propagation network) were employed to develop a
pedotransfer function for predicting soil parameter using easily
measurable characteristics of clay and organic carbon. The
performance of the multivariate regression and neural network model
was evaluated using a test data set. In order to evaluate the models,
root mean square error (RMSE) was used. The value of RMSE and
R2 derived by ANN model for CEC were 0.47 and 0.94 respectively,
while these parameters for multivariate regression model were 0.65
and 0.88 respectively. Results showed that artificial neural network
with seven neurons in hidden layer had better performance in
predicting soil cation exchange capacity than multivariate regression.
Abstract: Materials added to the matrix help improving operating properties of a composite. This experimental study has targeted to investigate this aim where Silicon Oxide particles were added to glass fibre and epoxy resin at an amount of 15% to the main material to obtain a sort of new composite material. Erosive wear behavior of epoxy-resin dipped composite materials reinforced with glass fibre and Silicon Oxide under three different impingement angles (30°, 60° and 90°), three different impact velocities (23, 34 and 53 m/s), two different angular Aluminum abrasive particle sizes (approximately 200 and 400 μm) and the fibre orientation of 45° (45/-45) were investigated. In the test results, erosion rates were obtained as functions of impingement angles, impact velocities, particle sizes and fibre orientation. Moreover, materials with addition of Silicon Oxide filler material exhibited lower wear as compared to neat materials with no added filler material. In addition, SEM views showing worn out surfaces of the test specimens were scrutinized.
Abstract: The main objective of this paper is to investigate the
enhancement of power system stability via coordinated tuning of
Power System Stabilizers (PSSs) in a multi-machine power system.
The design problem of the proposed controllers is formulated as an
optimization problem. Chaotic catfish particle swarm optimization
(C-Catfish PSO) algorithm is used to minimize the ITAE objective
function. The proposed algorithm is evaluated on a two-area, 4-
machines system. The robustness of the proposed algorithm is
verified on this system under different operating conditions and
applying a three-phase fault. The nonlinear time-domain simulation
results and some performance indices show the effectiveness of the
proposed controller in damping power system oscillations and this
novel optimization algorithm is compared with particle swarm
optimization (PSO).
Abstract: This paper investigates the problem of automated defect
detection for textile fabrics and proposes a new optimal filter design
method to solve this problem. Gabor Wavelet Network (GWN) is
chosen as the major technique to extract the texture features from
textile fabrics. Based on the features extracted, an optimal Gabor filter
can be designed. In view of this optimal filter, a new semi-supervised
defect detection scheme is proposed, which consists of one real-valued
Gabor filter and one smoothing filter. The performance of the scheme
is evaluated by using an offline test database with 78 homogeneous
textile images. The test results exhibit accurate defect detection with
low false alarm, thus showing the effectiveness and robustness of the
proposed scheme. To evaluate the detection scheme comprehensively,
a prototyped detection system is developed to conduct a real time test.
The experiment results obtained confirm the efficiency and
effectiveness of the proposed detection scheme.
Abstract: This research was conducted in the Lower Ping River
Basin downstream of the Bhumibol Dam and the Lower Wang River
Basin in Tak Province, Thailand. Most of the tributary streams of the
Ping can be considered as ungauged catchments. There are 10-
pumping station installation at both river banks of the Ping in Tak
Province. Recently, most of them could not fully operate due to the
water amount in the river below the level that would be pumping,
even though included water from the natural river and released flow
from the Bhumibol Dam. The aim of this research was to increase the
performance of those pumping stations using weir projects in the
Ping. Therefore, the river analysis system model (HEC-RAS) was
applied to study the hydraulic behavior of water surface profiles in
the Ping River with both cases of existing conditions and proposed
weirs during the violent flood in 2011 and severe drought in 2013.
Moreover, the hydrologic modeling system (HMS) was applied to
simulate lateral streamflow hydrograph from ungauged catchments of
the Ping. The results of HEC-RAS model calibration with existing
conditions in 2011 showed best trial roughness coefficient for the
main channel of 0.026. The simulated water surface levels fitted to
observation data with R2 of 0.8175. The model was applied to 3
proposed cascade weirs with 2.35 m in height and found surcharge
water level only 0.27 m higher than the existing condition in 2011.
Moreover, those weirs could maintain river water levels and increase
of those pumping performances during less river flow in 2013.
Abstract: Even though so many efforts have been taken to
renovate and renew the architecture of Miyaneh villages in cold and
dry regions of Iran-s northwest, these efforts failed due to lack of
significant study and ignoring the past and sustainable history of
those villages. Considering the overpopulation of Iran-s villages as
well as the importance in preventing their immigration to cities,
recognizing village architecture and its construction technology is of
great significance to attain sustainable residence in villages. As the
only vertical surface in the space, wall possesses its unique special
characteristics, and it is also a very important architectural element
able to provide the immunity and comfort space for the residents.
This article analyzes the characteristics of this vertical element, main
types of adobe and stone walls, locally constructed technologies,
implementation, the elements forming the walls in the frame of
village house typology of Miyaneh, which has the most villages in
East Azerbaijan, based on sustainable architectural construction
materials of walls.
Abstract: This paper presents a mean for reducing the torque
variation during the revolution of a vertical-axis wind turbine
(VAWT) by increasing the blade number. For this purpose, twodimensional
CDF analysis have been performed on a straight-bladed
Darreius-type rotor. After describing the computational model, a
complete campaign of simulations based on full RANS unsteady
calculations is proposed for a three, four and five-bladed rotor
architecture characterized by a NACA 0025 airfoil. For each
proposed rotor configuration, flow field characteristics are
investigated at several values of tip speed ratio, allowing a
quantification of the influence of blade number on flow geometric
features and dynamic quantities, such as rotor torque and power.
Finally, torque and power curves are compared for the analyzed
architectures, achieving a quantification of the effect of blade number
on overall rotor performance.
Abstract: Nowadays the construction industry is growing specially among developing counties. Iran also has a critical role in these industries in terms of workers disorders. Work-related musculoskeletal disorders (WMSDs) assign 7% of the whole diseases in the society, which make some limitations. One of the main factors, which are ended to WMSDs, is awkward posture. Steel bar bending is considered as one of the prominent performance among construction workers. In this case study we conducted to find the major tasks of bar benders and the most important related risk factors. This study was carried out among twenty workers (18-45 years) as our volunteer samples in some construction sites with less than 6 floors in two regions of Tehran municipality. The data was gathered through in depth observation, interview and questionnaire. Also postural analysis was done by OWAS. In another part of study we used NMQ for gathering some data about psychosocial effects of work related disorders. Our findings show that 64% of workers were not aware of work risks, also about 59% of workers had troubles in their wrists, hands, and especially among workers who worked in steel bar bending. In 46% cases low back pain were prevalence. Considering with gathered data and results, awkward postures and long term tasks and its duration are known as the main risk factors in WMSDs among construction workers, so work-rest schedule and also tools design should be considered to make an ergonomic condition for the mentioned workers.
Abstract: This work presents the hydrogen production from
steam gasification of palm kernel shell (PKS) at 700 oC in the
presence of 5% Ni/BEA and 5% Fe/BEA as catalysts. The steam
gasification was performed in two-staged reactors to evaluate the
effect of calcinations temperature and the steam to biomass ratio on
the product gas composition. The catalytic activity of Ni/BEA
catalyst decreases with increasing calcinations temperatures from 500
to 700 oC. The highest H2 concentration is produced by Fe/BEA
(600) with more than 71 vol%. The catalytic activity of the catalysts
tested is found to correspond to its physicochemical properties. The
optimum range for steam to biomass ratio if found to be between 2 to
4. Excess steam content results in temperature drop in the gasifier
which is undesirable for the gasification reactions.
Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.
Abstract: The objective of this paper is to establish a possible relationship between sustainable business practice and firm performance. Using a field survey methodology, a sample of sixty manufacturing companies in Nigeria was studied. The firms were categorised into two groups, environmentally 'responsible' and 'irresponsible' firms. An investigation was undertaken into the possible relationship between firm performance and three selected indicators of sustainable business practice: employee health and safety (EHS), waste management (WM), and community development (CD), common within the 30 'responsible' firms. Findings from empirical results reveal that the sustainable practices of the 'responsible' firms are significantly related with firm performance. In addition, sustainable practices are inversely related with fines and penalties. The paper concludes that, within the Nigerian setting at least, sustainability affects corporate performance and sustainability may be a possible tool for corporate conflict resolution as evidenced in the reduction of fines, penalties and compensations. The paper therefore recommends research into the relationship between sustainability and conflict management.