Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: Cloud computing has emerged as a promising
direction for cost efficient and reliable service delivery across data
communication networks. The dynamic location of service facilities
and the virtualization of hardware and software elements are stressing
the communication networks and protocols, especially when data
centres are interconnected through the internet. Although the
computing aspects of cloud technologies have been largely
investigated, lower attention has been devoted to the networking
services without involving IT operating overhead. Cloud computing
has enabled elastic and transparent access to infrastructure services
without involving IT operating overhead. Virtualization has been a
key enabler for cloud computing. While resource virtualization and
service abstraction have been widely investigated, networking in
cloud remains a difficult puzzle. Even though network has significant
role in facilitating hybrid cloud scenarios, it hasn't received much
attention in research community until recently. We propose Network
as a Service (NaaS), which forms the basis of unifying public and
private clouds. In this paper, we identify various challenges in
adoption of hybrid cloud. We discuss the design and implementation
of a cloud platform.
Abstract: Amoxicillin is an antibiotic which is widely used to
treat various infections in both human beings and animals. However,
when amoxicillin is released into the environment, it is a major
problem. Amoxicillin causes bacterial resistance to these drugs and
failure of treatment with antibiotics. Liquid membrane is of great
interest as a promising method for the separation and recovery of the
target ions from aqueous solutions due to the use of carriers for the
transport mechanism, resulting in highly selectivity and rapid
transportation of the desired metal ions. The simultaneous processes
of extraction and stripping in a single unit operation of liquid
membrane system are very interesting. Therefore, it is practical to
apply liquid membrane, particularly the HFSLM for industrial
applications as HFSLM is proved to be a separation process with
lower capital and operating costs, low energy and extractant with
long life time, high selectivity and high fluxes compared with solid
membranes. It is a simple design amenable to scaling up for industrial
applications. The extraction and recovery for (Amoxicillin) through
the hollow fiber supported liquid membrane (HFSLM) using
aliquat336 as a carrier were explored with the experimental data. The
important variables affecting on transport of amoxicillin viz.
extractant concentration and operating time were investigated. The
highest AMOX- extraction percentages of 85.35 and Amoxicillin
stripping of 80.04 were achieved with the best condition at 6 mmol/L
[aliquat336] and operating time 100 min. The extraction reaction
order (n) and the extraction reaction rate constant (kf) were found to
be 1.00 and 0.0344 min-1, respectively.
Abstract: Current systems complexity has reached a degree that
requires addressing conception and design issues while taking into
account environmental, operational, social, legal and financial
aspects. Therefore, one of the main challenges is the way complex
systems are specified and designed. The exponential growing effort,
cost and time investment of complex systems in modeling phase
emphasize the need for a paradigm, a framework and an environment
to handle the system model complexity. For that, it is necessary to
understand the expectations of the human user of the model and his
limits. This paper presents a generic framework for designing
complex systems, highlights the requirements a system model needs
to fulfill to meet human user expectations, and suggests a graphbased
formalism for modeling complex systems. Finally, a set of
transformations are defined to handle the model complexity.
Abstract: Construction projects are information intensive in
nature and involve many activities that are related to each other.
Wireless technologies can be used to improve the accuracy and
timeliness of data collected from construction sites and shares it with
appropriate parties. Nonetheless, the construction industry tends to be
conservative and shows hesitation to adopt new technologies. A main
concern for owners, contractors or any person in charge on a job site
is the cost of the technology in question. Wireless technologies are
not cheap. There are a lot of expenses to be taken into consideration,
and a study should be completed to make sure that the importance
and savings resulting from the usage of this technology is worth the
expenses. This research attempts to assess the effectiveness of using
the appropriate wireless technologies based on criteria such as
performance, reliability, and risk. The assessment is based on a utility
function model that breaks down the selection issue into alternatives
attribute. Then the attributes are assigned weights and single
attributes are measured. Finally, single attribute are combined to
develop one single aggregate utility index for each alternative.
Abstract: We used live E. coli containing synthetic genetic
oscillators to study how the degree of synchrony between the genetic
circuits of sister cells changes with temperature. We found that both
the mean and the variability of the degree of synchrony between the
fluorescence signals from sister cells are affected by temperature.
Also, while most pairs of sister cells were found to be highly
synchronous in each condition, the number of asynchronous pairs
increased with increasing temperature, which was found to be due to
disruptions in the oscillations. Finally we provide evidence that these
disruptions tend to affect multiple generations as opposed to
individual cells. These findings provide insight in how to design
more robust synthetic circuits and in how cell division can affect their
dynamics.
Abstract: In this paper, the energy saving and human thermal
comfort in a typical office room are investigated. The impact of a
combined system of exhaust inlet air with light slots located at the
ceiling level in a room served by displacement ventilation system is
numerically modelled. Previous experimental data are used to
validate the Computational Fluid Dynamic (CFD) model. A case
study of simulated office room includes two seating occupants, two
computers, two data loggers and four lamps. The combined system is
located at the ceiling level above the heat sources. A new method of
calculation for the cooling coil load in Stratified Air Distribution
(STRAD) system is used in this study. The results show that 47.4%
energy saving of space cooling load can be achieved by combing the
exhaust inlet air with light slots at the ceiling level above the heat
sources.
Abstract: The effect of processing on plasma lipid profile and
atherogenic indices of rats fed Artocarpus heterophyllus seed diets at
different concentrations were investigated. Fifty five rats were used
for this study, they were divided into eleven groups of five rats each
(one control group and ten test groups), the test groups were fed raw,
boiled, roasted, fermented and soaked diets at 10% and 40%
concentrations. The study lasted for thirty five days. The diets led to
significant decrease (p
Abstract: This paper presents a rheological model for producing
shape-memory thermoplastic polymers. Shape-memory occurs as a
result of internal rearrangement of the structural elements of a
polymer. A non-linear viscoelastic model was developed that allows
qualitative and quantitative prediction of the stress-strain behavior of
shape-memory polymers during heating. This research was done to
develop a technique to determine the maximum possible change in
size of shape-memory products during heating. The rheological
model used in this work was particularly suitable for defining process
parameters and constructive parameters of the processing equipment.
Abstract: Mustard leaves are rich in folates, vitamin A, K and
B-complex. Mustard greens are low in calories and fats and rich in
dietary fiber. They are rich in potassium, manganese, iron, copper,
calcium, magnesium and low in sodium. It is very rich in antioxidants
and Phytonutrients. For the optimization of process variables
(moisture content and mustard leave powder), the experiments were
conducted according to central composite Face Centered Composite
design of RSM. The mustard leaves powder was replaced with
composite flour (a combination of rice, chickpea and corn in the ratio
of 70:15:15). The extrudate was extruded in a twin screw extruder at
a barrel temperature of 120°C. The independent variables were
mustard leaves powder (2-10 %) and moisture content (12-20 %).
Responses analyzed were bulk density, water solubility index, water
absorption index, lateral expansion, antioxidant activity, total
phenolic content, and overall acceptability. The optimum conditions
obtained were 7.19 g mustard leaves powder in 100g premix having
16.8% moisture content (w.b).
Abstract: This study aims at developing a novel cold asphalt
concrete binder course mixture by using Ordinary Portland Cement
(OPC) as a replacement for conventional mineral filler (0%-100%)
with new by-product material (LJMU-A2) used as a supplementary
cementitious material. With this purpose, cold asphalt concrete binder
course mixtures with cationic emulsions were studied by means of
stiffness modulus whereas water sensitivity was assessed by
measuring the stiffness modulus ratio before and after sample
conditioning.
The results indicate that a substantial enhancement in the stiffness
modulus and a considerable improvement of water sensitivity
resistance is achieved by adding LJMU-A2 to the cold asphalt
mixtures as a supplementary cementitious material. Moreover, the
addition of LJMU-A2 to those mixtures leads to a stiffness modulus
after 2-day curing compared to that obtained with Portland cement,
which occurs after 7-day curing.
Abstract: Most of the oil palm plantations have been threatened
by Basal Stem Rot (BSR) disease which causes serious economic
impact. This study was conducted to identify the healthy and BSRinfected
oil palm tree using thirteen color indices. Multispectral and
thermal camera was used to capture 216 images of the leaves taken
from frond number 1, 9 and 17. Indices of normalized difference
vegetation index (NDVI), red (R), green (G), blue (B), near infrared
(NIR), green – blue (GB), green/blue (G/B), green – red (GR),
green/red (G/R), hue (H), saturation (S), intensity (I) and thermal
index (T) were used. From this study, it can be concluded that G
index taken from frond number 9 is the best index to differentiate
between the healthy and BSR-infected oil palm trees. It not only gave
high value of correlation coefficient (R=-0.962), but also high value
of separation between healthy and BSR-infected oil palm tree.
Furthermore, power and S model developed using G index gave the
highest R2 value which is 0.985.
Abstract: The goal of the paper is to highlight the effect of the
building design and epicentral distance on the storey lateral
displacements, for several reinforced concrete buildings (6, 9 and 12
stories). These structures are subjected to seismic accelerations from
the Boumerdes earthquake (Algeria, May 21st, Mw = 6.8). Using the
response spectrum method (modal spectral approach), the analysis is
performed in both longitudinal and transverse directions. The
building design is expressed through the fundamental period and
epicentral distance is used to represent the earthquake effect variation
on storey lateral displacements and interstory drift for the considered
buildings.
Abstract: Cyberspace has become a more viable arena for
budding artists to share musical acts through digital forms. The
increasing relevance of online communities has attracted scholars
from various fields demonstrating its influence on social capital. This
paper extends this understanding of social capital among Filipino
music artists belonging to the SoundCloud Philippines Facebook
Group.
The study makes use of various qualitative data obtained from
key-informant interviews and participant observation of online and
physical encounters, analyzed using the case study approach.
Soundcloud Philippines has over seven-hundred members and is
composed of Filipino singers, instrumentalists, composers, arrangers,
producers, multimedia artists and event managers. Group interactions
are a mix of online encounters based on Facebook and SoundCloud
and physical encounters through meet-ups and events. Benefits
reaped from the community are informational, technical,
instrumental, promotional, motivational and social support. Under the
guidance of online group administrators, collaborative activities such
as music productions, concerts and events transpire. Most conflicts
and problems arising are resolved peacefully. Social capital in
SoundCloud Philippines is mobilized through recognition, respect
and reciprocity.
Abstract: The Chair of Thermal Engineering at Poznan
University of Technology has been conducted research works on the
possibilities of using carbon nanostructures in energy and mechanics
applications for a couple of years. Those studies have provided results in a form of co-operation with foreign research centres, numerous publications and patent
applications.
Authors of this paper have studied the influence of multi-walled
carbon nanostructures on changes in static friction arising when steel
surfaces were moved. Tests were made using the original test stand
consisting of automatically controlled inclined plane driven by
precise stepper motors. Computer program created in the LabView
environment was responsible for monitoring of the stand operation,
accuracy of measurements and archiving the obtained results. Such a
solution enabled to obtain high accuracy and repeatability of all
conducted experiments.
Tests and analysis of the obtained results allowed us to determine
how additional layers of carbon nanostructures influenced on changes
of static friction coefficients. At the same time, we analyzed the
potential possibilities of applying nanostructures under consideration
in mechanics.
Abstract: One of the functions of the commercial heavy vehicle
is to safely and efficiently transport goods and people. Due to its size
and carrying capacity, it is important to study the vehicle dynamic
stability during cornering. Study has shown that there are a number of
overloaded heavy vehicles or permissible Gross Vehicle Weight
(GVW) violations recorded at selected areas in Malaysia assigned by
its type and category. Thus, the objective of this study is to
investigate the correlation and effect of the GVW on heavy vehicle
stability during cornering event using simulation. Various selected
heavy vehicle types and category are simulated using IPG/Truck
Maker® with different GVW and road condition (coefficient of
friction of road surface), while the speed, driver characteristic, center
of gravity of load and road geometry are constant. Based on the
analysis, the relationship between GVW and lateral acceleration were
established. As expected, on the same value of coefficient of friction,
the maximum lateral acceleration would be increased as the GVW
increases.
Abstract: Remote arid areas of the vast expanses of the African
deserts hold huge subterranean reserves of brackish water resources
waiting for economic development. This work presents design
guidelines as well as initial performance data of new autonomous
solar desalination equipment which could help local communities
produce their own fresh water using solar energy only and, why not,
contribute to transforming desert lands into lush gardens. The output
of solar distillation equipments are typically low and in the range of 3
l/m2/day on the average. This new design with an integrated, water
based, environmentally-friendly solar heat storage system produced 5
l/m2/day in early spring weather. Equipment output during summer
exceeded 9 liters per m2 per day.
Abstract: This paper presents the ‘Eye Ball Motion Controlled
Wheelchair using IR Sensors’ for the elderly and differently abled
people. In this eye tracking based technology, three Proximity
Infrared (IR) sensor modules are mounted on an eye frame to trace
the movement of the iris. Since, IR sensors detect only white objects;
a unique sequence of digital bits is generated corresponding to each
eye movement. These signals are then processed via a micro
controller IC (PIC18F452) to control the motors of the wheelchair.
The potential and efficiency of previously developed rehabilitation
systems that use head motion, chin control, sip-n-puff control, voice
recognition, and EEG signals variedly have also been explored in
detail. They were found to be inconvenient as they served either
limited usability or non-affordability. After multiple regression
analyses, the proposed design was developed as a cost-effective,
flexible and stream-lined alternative for people who have trouble
adopting conventional assistive technologies.
Abstract: Let us consider that the entire universe is composed of
a single hydrogen atom within which the electron is moving around
the proton. In this case, according to classical theories of physics,
radiation, photons respectively, should be absorbed by the electron.
Depending on the number of photons absorbed, the electron radius of
rotation around the proton is established. Until now, the principle of
photons absorption by electrons and the electron transition to a new
energy level, namely to a higher radius of rotation around the proton,
is not clarified in physics. This paper aims to demonstrate that
radiation, photons respectively, have mass and negative electrostatic
charge similar to electrons but infinitely smaller. The experiments
which demonstrate this theory are simple: thermal expansion,
photoelectric effect and thermonuclear reaction.