Abstract: These Monolayer and multilayer coatings of CrN and
AlCrN deposited on 100Cr6 (AISI 52100) substrate by PVD
magnetron sputtering system. The microstructures of the coatings
were characterized using atomic force microscopy (AFM). The AFM
analysis revealed the presence of domes and craters that are
uniformly distributed over all surfaces of the various layers.
Nanoindentation measurement of CrN coating showed maximum
hardness (H) and modulus (E) of 14 GPa and 190 GPa, respectively.
The measured H and E values of AlCrN coatings were found to be 30
GPa and 382 GPa, respectively. The improved hardness in both the
coatings was attributed mainly to a reduction in crystallite size and
decrease in surface roughness. The incorporation of Al into the CrN
coatings has improved both hardness and Young’s modulus.
Abstract: This paper is based on a large questionnaire study. The
paper presents how all participants and subgroups (upper- and
lower-level white-collar workers) answered the question, “Have you
had an ache, pain, or numbness, which you associate with desktop
computer use, in the different body parts during the last 12 months?’
14.6% of participants (19.4% of women and 8.2% of men) reported
that they had often or very often physical symptoms in the neck. Even
if our results cannot prove a causal relation of symptoms with
computer use, show that workers believe that computer use can
influence their wellbeing: this is important when devising treatment
modalities to decrease these physical symptoms.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: This study utilizes a frequency domain approach over
the period of 1996 to 2013 to examine the causal relationship between
governance and economic growth in ten Asian countries, which have
different levels of democracy; classified as “Free”, “Partly Free”, and
“Not Free” countries. The empirical results show that there is no
Granger causality running from governance to economic growth in
“Not Free” countries and “Partly Free” countries with the exception of
Singapore. As for “Free” countries such as South Korea and Taiwan,
there is a one-way causality running from governance to economic
growth. The findings of this study indicate that policy makers in South
Korea, Taiwan, and Singapore could use governance index to improve
their predictions of the future economic growth.
Abstract: This work presents an improved single fiber pull-out
test for fiber/matrix interface characterization. This test has been
used to study the Inter-Facial Shear Strength ‘IFSS’ of hemp fibers
reinforced polypropylene (PP). For this aim, the fiber diameter
has been carefully measured using a tomography inspired method.
The fiber section contour can then be approximated by a circle
or a polygon. The results show that the IFSS is overestimated if
the circular approximation is used. The Influence of the molding
temperature on the IFSS has also been studied. We find that a molding
temperature of 183◦C leads to better interfacial properties. Above or
below this temperature the interface strength is reduced.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: In this study, to clarify the effectiveness of an
aluminum/chromium/tungsten-based-coated tool for cutting sintered
steel, tool wear was experimentally investigated. The sintered steel
was turned with the (Al60,Cr25,W15)N-, (Al60,Cr25,W15)(C,N)- and
(Al64,Cr28,W8)(C,N)-coated cemented carbide tools according to the
physical vapor deposition (PVD) method. Moreover, the tool wear of
the aluminum/chromium/tungsten-based-coated item was compared
with that of the (Al,Cr)N coated tool. Furthermore, to clarify the tool
wear mechanism of the aluminum/chromium/tungsten-coating film for
cutting sintered steel, Scanning Electron Microscope observation and
Energy Dispersive x-ray Spectroscopy mapping analysis were
conducted on the abraded surface. The following results were
obtained: (1) The wear progress of the (Al64,Cr28,W8)(C,N)-coated
tool was the slowest among that of the five coated tools. (2) Adding
carbon (C) to the aluminum/chromium/tungsten-based-coating film
was effective for improving the wear-resistance. (3) The main wear
mechanism of the (Al60,Cr25,W15)N-, the (Al60,Cr25,W15)(C,N)-
and the (Al64,Cr28,W8)(C,N)-coating films was abrasive wear.
Abstract: The economic use and ease of construction of profiled
deck composite slab is marred with the complex and un-economic
strength verification required for the serviceability and general safety
considerations. Beside these, albeit factors such as shear span length,
deck geometries and mechanical frictions greatly influence the
longitudinal shear strength, that determines the ultimate strength of
profiled deck composite slab, and number of methods available for its
determination; partial shear and slope-intercept are the two methods
according to Euro-code 4 provision. However, the complexity
associated with shear behavior of profiled deck composite slab, the
use of these methods in determining the load carrying capacities of
such slab yields different and conflicting values. This couple with the
time and cost constraint associated with the strength verification is a
source of concern that draws more attentions nowadays, the issue is
critical. Treating some of these known shear strength influencing
factors as random variables, the load carrying capacity violation of
profiled deck composite slab from the use of the two-methods
defined according to Euro-code 4 are determined using reliability
approach, and comparatively studied. The study reveals safety values
from the use of m-k method shows good standing compared with that
from the partial shear method.
Abstract: The aim of the present study is to detect the chaotic
behavior in monetary economic relevant dynamical system. The
study employs three different forms of Taylor rules: current, forward,
and backward looking. The result suggests the existence of the
chaotic behavior in all three systems. In addition, the results strongly
represent that using expectations in policy rule especially rational
expectation hypothesis can increase complexity of the system and
leads to more chaotic behavior.
Abstract: We apply the non-parametric, unconditional,
hyperbolic order-α quantile estimator to appraise the relative
efficiency of Microfinance Institutions in Africa in terms of outreach.
Our purpose is to verify if these institutions, which must constantly
try to strike a compromise between their social role and financial
sustainability are operationally efficient.
Using data on African MFIs extracted from the Microfinance
Information eXchange (MIX) database and covering the 2004 to
2006 periods, we find that more efficient MFIs are also the most
profitable. This result is in line with the view that social performance
is not in contradiction with the pursuit of excellent financial
performance. Our results also show that large MFIs in terms of asset
and those charging the highest fees are not necessarily the most
efficient.
Abstract: Superabsorbent polymers received much attention and
are used in many fields because of their superior characters to
traditional absorbents, e.g., sponge and cotton. So, it is very
important but challenging to prepare highly and fast-swelling
superabsorbents. A reliable, efficient and low-cost technique for
removing heavy metal ions from wastewater is the adsorption using
bio-adsorbents obtained from biological materials, such as
polysaccharides-based hydrogels superabsorbents. In this study, novel multi-functional superabsorbent composites
type semi-interpenetrating polymer networks (Semi-IPNs) were
prepared via graft polymerization of acrylamide onto chitosan
backbone in presence of gelatin, CTS-g-PAAm/Ge, using potassium
persulfate and N,N’-methylene bisacrylamide as initiator and
crosslinker, respectively. These hydrogels were also partially
hydrolyzed to achieve superabsorbents with ampholytic properties
and uppermost swelling capacity. The formation of the grafted
network was evidenced by Fourier Transform Infrared Spectroscopy
(ATR-FTIR) and Thermogravimetric Analysis (TGA). The porous
structures were observed by Scanning Electron Microscope (SEM).
From TGA analysis, it was concluded that the incorporation of the Ge
in the CTS-g-PAAm network has marginally affected its thermal
stability. The effect of gelatin content on the swelling capacities of
these superabsorbent composites was examined in various media
(distilled water, saline and pH-solutions). The water absorbency was
enhanced by adding Ge in the network, where the optimum value was
reached at 2 wt. % of Ge. Their hydrolysis has not only greatly
optimized their absorption capacity but also improved the swelling
kinetic.These materials have also showed reswelling ability. We
believe that these super-absorbing materials would be very effective
for the adsorption of harmful metal ions from wastewater.
Abstract: This paper describes a new approach which can be
used to interpret the experimental creep deformation data obtained
from miniaturized thin plate bending specimen test to the
corresponding uniaxial data based on an inversed application of the
reference stress method. The geometry of the thin plate is fully
defined by the span of the support, l, the width, b, and the thickness,
d. Firstly, analytical solutions for the steady-state, load-line creep
deformation rate of the thin plates for a Norton’s power law under
plane stress (b→0) and plane strain (b→∞) conditions were obtained,
from which it can be seen that the load-line deformation rate of the
thin plate under plane-stress conditions is much higher than that
under the plane-strain conditions. Since analytical solution is not
available for the plates with random b-values, finite element (FE)
analyses are used to obtain the solutions. Based on the FE results
obtained for various b/l ratios and creep exponent, n, as well as the
analytical solutions under plane stress and plane strain conditions, an
approximate, numerical solutions for the deformation rate are
obtained by curve fitting. Using these solutions, a reference stress
method is utilised to establish the conversion relationships between
the applied load and the equivalent uniaxial stress and between the
creep deformations of thin plate and the equivalent uniaxial creep
strains. Finally, the accuracy of the empirical solution was assessed
by using a set of “theoretical” experimental data.
Abstract: Processing of Al-19.4Si alloy by high intensive
electron beam has been carried out and multiple increases in fatigue
life of the material have been revealed. Investigations of structure and
surface modified layer destruction of Al-19.4Si alloy subjected to
multicycle fatigue tests to fracture have been carried out by methods
of scanning electron microscopy. The factors responsible for the
increase of fatigue life of Al-19.4Si alloy have been revealed and
analyzed.
Abstract: In this study, nuclear magnetic resonance
spectroscopy and nuclear quadrupole resonance spectroscopy
parameters of 14N (Nitrogen in imidazole ring) in N–H…O hydrogen
bonding for Histidine hydrochloride monohydrate were calculated via
density functional theory. We considered a five-molecule model
system of Histidine hydrochloride monohydrate. Also we examined
the trends of environmental effect on hydrogen bonds as well as
cooperativity. The functional used in this research is M06-2X which
is a good functional and the obtained results has shown good
agreement with experimental data. This functional was applied to
calculate the NMR and NQR parameters. Some correlations among
NBO parameters, NMR and NQR parameters have been studied
which have shown the existence of strong correlations among them.
Furthermore, the geometry optimization has been performed using
M062X/6-31++G(d,p) method. In addition, in order to study
cooperativity and changes in structural parameters, along with
increase in cluster size, natural bond orbitals have been employed.
Abstract: In the cooperative transmission scheme, both the
cellular system and broadcasting system are composed. Two cellular
base stations (CBSs) communicating with a user in the cell edge use
cooperative transmission scheme in the conventional scheme. In the
case that the distance between two CBSs and the user is distant, the
conventional scheme does not guarantee the quality of the
communication because the channel condition is bad. Therefore, if the
distance between CBSs and a user is distant, the performance of the
conventional scheme is decreased. Also, the bad channel condition has
bad effects on the performance. The proposed scheme uses two relays
to communicate well with CBSs when the channel condition between
CBSs and the user is poor. Using the relay in the high attenuation
environment can obtain both advantages of the high bit error rate
(BER) and throughput performance.
Abstract: Artificial neural networks have gained a lot of interest
as empirical models for their powerful representational capacity,
multi input and output mapping characteristics. In fact, most feedforward
networks with nonlinear nodal functions have been proved to
be universal approximates. In this paper, we propose a new
supervised method for color image classification based on selforganizing
feature maps (SOFM). This algorithm is based on
competitive learning. The method partitions the input space using
self-organizing feature maps to introduce the concept of local
neighborhoods. Our image classification system entered into RGB
image. Experiments with simulated data showed that separability of
classes increased when increasing training time. In additional, the
result shows proposed algorithms are effective for color image
classification.
Abstract: Aurèsregion is one of the arid and semi-arid areas that
have suffered climate crises and overexploitation of natural resources
they have led to significant land degradation. The use of remote sensing data allowed us to analyze the land and
its spatiotemporal changes in the Aurès between 1987 and 2013, for
this work, we adopted a method of analysis based on the exploitation
of the images satellite Landsat TM 1987 and Landsat OLI 2013, from
the supervised classification likelihood coupled with field surveys of
the mission of May and September of 2013. Using ENVI EX software by the superposition of the ground cover
maps from 1987 and 2013, one can extract a spatial map change of
different land cover units. The results show that between 1987 and
2013 vegetation has suffered negative changes are the significant
degradation of forests and steppe rangelands, and sandy soils and
bare land recorded a considerable increase. The spatial change map land cover units between 1987 and 2013
allows us to understand the extensive or regressive orientation of
vegetation and soil, this map shows that dense forests give his place
to clear forests and steppe vegetation develops from a degraded forest
vegetation and bare, sandy soils earn big steppe surfaces that explain
its remarkable extension.
The analysis of remote sensing data highlights the profound
changes in our environment over time and quantitative monitoring of
the risk of desertification.
Abstract: Numerical investigations were conducted to study the
influence of flexural reinforcement ratio on the diagonal cracking
strength and ultimate shear strength of reinforced concrete (RC)
beams without stirrups. Three-dimensional nonlinear finite element
analyses (FEAs) of the beams with flexural reinforcement ratios
ranging from 0.58% to 2.20% subjected to a mid-span concentrated
load were carried out. It is observed that the load-deflection and loadstrain
curves obtained from the numerical analyses agree with those
obtained from the experiments. It is concluded that flexural
reinforcement ratio has a significant effect on the shear strength and
deflection capacity of RC beams without stirrups. The predictions of
diagonal cracking strength and ultimate shear strength of beams
obtained by using the equations defined by a number of codes and
researchers are compared with each other and with the experimental
values.
Abstract: Accurate forecasting of fresh produce demand is one
the challenges faced by Small Medium Enterprise (SME)
wholesalers. This paper is an attempt to understand the cause for the
high level of variability such as weather, holidays etc., in demand of
SME wholesalers. Therefore, understanding the significance of
unidentified factors may improve the forecasting accuracy. This
paper presents the current literature on the factors used to predict
demand and the existing forecasting techniques of short shelf life
products. It then investigates a variety of internal and external
possible factors, some of which is not used by other researchers in the
demand prediction process. The results presented in this paper are
further analysed using a number of techniques to minimize noise in
the data. For the analysis past sales data (January 2009 to May 2014)
from a UK based SME wholesaler is used and the results presented
are limited to product ‘Milk’ focused on café’s in derby. The
correlation analysis is done to check the dependencies of variability
factor on the actual demand. Further PCA analysis is done to
understand the significance of factors identified using correlation.
The PCA results suggest that the cloud cover, weather summary and
temperature are the most significant factors that can be used in
forecasting the demand. The correlation of the above three factors
increased relative to monthly and becomes more stable compared to
the weekly and daily demand.
Abstract: High Voltage Direct Current (HVDC) power
transmission is employed to move large amounts of electric power.
There are several possibilities to enhance the transient stability in a
power system. One adequate option is by using the high
controllability of the HVDC if HVDC is available in the system. This
paper presents a control technique for HVDC to enhance the transient
stability. The strategy controls the power through the HVDC to help
make the system more transient stable during disturbances. Loss of
synchronism is prevented by quickly producing sufficient
decelerating energy to counteract accelerating energy gained during.
In this study, the power flow in the HVDC link is modulated with the
addition of an auxiliary signal to the current reference of the rectifier
firing angle controller. This modulation control signal is derived from
speed deviation signal of the generator utilizing a PD controller; the
utilization of a PD controller is suitable because it has the property of
fast response. The effectiveness of the proposed controller is
demonstrated with a SMIB test system.