Abstract: Pressure wave velocity in a hydraulic system was
determined using piezo pressure sensors without removing fluid from
the system. The measurements were carried out in a low pressure
range (0.2 – 6 bar) and the results were compared with the results of
other studies. This method is not as accurate as measurement with
separate measurement equipment, but the fluid is in the actual
machine the whole time and the effect of air is taken into
consideration if air is present in the system. The amount of air is
estimated by calculations and comparisons between other studies.
This measurement equipment can also be installed in an existing
machine and it can be programmed so that it measures in real time.
Thus, it could be used e.g. to control dampers.
Abstract: The tubes in an Ammonia primary reformer furnace
operate close to the limits of materials technology in terms of the
stress induced as a result of very high temperatures, combined with
large differential pressures across the tube wall. Operation at tube
wall temperatures significantly above design can result in a rapid
increase in the number of tube failures, since tube life is very
sensitive to the absolute operating temperature of the tube. Clearly it
is important to measure tube wall temperatures accurately in order to
prevent premature tube failure by overheating.. In the present study,
the catalyst tubes in an Ammonia primary reformer has been modeled
taking into consideration heat, mass and momentum transfer as well
as reformer characteristics.. The investigations concern the effects of
tube characteristics and superficial tube wall temperatures on of the
percentage of heat flux, unconverted methane and production of
Hydrogen for various values of steam to carbon ratios. The results
show the impact of catalyst tubes length and diameters on the
performance of operating parameters in ammonia primary reformers.
Abstract: In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.
Abstract: In this study, a vibration analysis was carried out of
symmetric angle-ply laminated composite plates with and without
square hole when subjected to compressive loads, numerically. A
buckling analysis is also performed to determine the buckling load of
laminated plates. For each fibre orientation, the compression load is
taken equal to 50% of the corresponding buckling load. In the
analysis, finite element method (FEM) was applied to perform
parametric studies, the effects of degree of orthotropy and stacking
sequence upon the fundamental frequencies and buckling loads are
discussed. The results show that the presence of a constant
compressive load tends to reduce uniformly the natural frequencies
for materials which have a low degree of orthotropy. However, this
reduction becomes non-uniform for materials with a higher degree of
orthotropy.
Abstract: loss of feedwater accident is one of the frequently sever accidents in steam boiler facilities. It threatens the system structural integrity and generates serious hazards and economic loses. The safety analysis of the thermal installations, based extensively on the numeric simulation. The simulation analysis using realistic computer codes like Relap5/Mod3.2 will help understand steam boiler thermal-hydraulic behavior during normal and abnormal conditions. In this study, we are interested on the evaluation of the radiant steam boiler assessment and response to loss-of-feedwater accident. Pressure, temperature and flow rate profiles are presented in various steam boiler system components. The obtained results demonstrate the importance and capability of the Relap5/Mod3.2 code in the thermal-hydraulic analysis of the steam boiler facilities.
Abstract: Blind Signature were introduced by Chaum. In this
scheme, a signer can “sign” a document without knowing the
document contain. This is particularly important in electronic voting.
CryptO-0N2 is an electronic voting protocol which is development of
CryptO-0N. During its development this protocol has not been
furnished with the requirement of blind signature, so the choice of
voters can be determined by counting center. In this paper will be
presented of implementation of blind signature using RSA algorithm.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: Many real-world data sets consist of a very high dimensional feature space. Most clustering techniques use the distance or similarity between objects as a measure to build clusters. But in high dimensional spaces, distances between points become relatively uniform. In such cases, density based approaches may give better results. Subspace Clustering algorithms automatically identify lower dimensional subspaces of the higher dimensional feature space in which clusters exist. In this paper, we propose a new clustering algorithm, ISC – Intelligent Subspace Clustering, which tries to overcome three major limitations of the existing state-of-art techniques. ISC determines the input parameter such as є – distance at various levels of Subspace Clustering which helps in finding meaningful clusters. The uniform parameters approach is not suitable for different kind of databases. ISC implements dynamic and adaptive determination of Meaningful clustering parameters based on hierarchical filtering approach. Third and most important feature of ISC is the ability of incremental learning and dynamic inclusion and exclusions of subspaces which lead to better cluster formation.
Abstract: We present a prototype interactive (hyper) map of strategic, tactical, and logistic options for Supply Chain Management. The map comprises an anthology of options, broadly classified within the strategic spectrum of efficiency versus responsiveness, and according to logistic and cross-functional drivers. They are exemplified by cases in diverse industries. We seek to get all these information and ideas organized to help supply chain managers identify effective choices for specific business environments. The key and innovative linkage we introduce is the configuration of competitive forces. Instead of going through seemingly endless and isolated cases and wondering how one can borrow from them, we aim to provide a guide by force comparisons. The premise is that best practices in a different industry facing similar forces may be a most productive resource in supply chain design and planning. A prototype template is demonstrated.
Abstract: The noteworthy point in the advancement of Brain Machine Interface (BMI) research is the ability to accurately extract features of the brain signals and to classify them into targeted control action with the easiest procedures since the expected beneficiaries are of disabled. In this paper, a new feature extraction method using the combination of adaptive band pass filters and adaptive autoregressive (AAR) modelling is proposed and applied to the classification of right and left motor imagery signals extracted from the brain. The introduction of the adaptive bandpass filter improves the characterization process of the autocorrelation functions of the AAR models, as it enhances and strengthens the EEG signal, which is noisy and stochastic in nature. The experimental results on the Graz BCI data set have shown that by implementing the proposed feature extraction method, a LDA and SVM classifier outperforms other AAR approaches of the BCI 2003 competition in terms of the mutual information, the competition criterion, or misclassification rate.
Abstract: Prickly pear (Opuntia spp) fruit has received renewed
interest since it contains a betalain pigment that has an attractive
purple colour for the production of juice. Prickly pear juice was
prepared by homogenizing the fruit and treating the pulp with 48 g of
pectinase from Aspergillus niger. Titratable acidity was determined
by diluting 10 ml prickly pear juice with 90 ml deionized water and
titrating to pH 8.2 with 0.1 N NaOH. Brix was measured using a
refractometer and ascorbic acid content assayed
spectrophotometrically. Colour variation was determined
colorimetrically (Hunter L.a.b.). Hunter L.a.b. analysis showed that
the red purple colour of prickly pear juice had been affected by juice
treatments. This was indicated by low light values of colour
difference meter (CDML*), hue, CDMa* and CDMb* values. It was
observed that non-treated prickly pear juice had a high (colour
difference meter of light) CDML* of 3.9 compared to juice
treatments (range 3.29 to 2.14). The CDML* significantly (p
Abstract: This paper presents a model for an unreliable
production line, which is operated according to demand with constant
work-in-process (CONWIP). A simulation model is developed based
on the discrete model and several case problems are analyzed using
the model. The model is utilized to optimize storage space capacities
at intermediate stages and the number of kanbans at the last stage,
which is used to trigger the production at the first stage. Furthermore,
effects of several line parameters on production rate are analyzed
using design of experiments.
Abstract: There is strong evidence that water channel proteins
'aquaporins (AQPs)' are central components in plant-water relations
as well as a number of other physiological parameters. We had
previously reported the isolation of 24 plasma membrane intrinsic
protein (PIP) type AQPs. However, the gene numbers in rice and the
polyploid nature of bread wheat indicated a high probability of
further genes in the latter. The present work focused on identification
of further AQP isoforms in bread wheat. With the use of altered
primer design, we identified five genes homologous, designated
PIP1;5b, PIP2;9b, TaPIP2;2, TaPIP2;2a, TaPIP2;2b. Sequence
alignments indicate PIP1;5b, PIP2;9b are likely to be homeologues of
two previously reported genes while the other three are new genes
and could be homeologs of each other. The results indicate further
AQP diversity in wheat and the sequence data will enable physical
mapping of these genes to identify their genomes as well as genetic to
determine their association with any quantitative trait loci (QTLs)
associated with plant-water relation such as salinity or drought
tolerance.
Abstract: In this paper, the melting of a semi-infinite body as a
result of a moving laser beam has been studied. Because the Fourier
heat transfer equation at short times and large dimensions does not
have sufficient accuracy; a non-Fourier form of heat transfer
equation has been used. Due to the fact that the beam is moving in x
direction, the temperature distribution and the melting pool shape are
not asymmetric. As a result, the problem is a transient threedimensional
problem. Therefore, thermophysical properties such as
heat conductivity coefficient, density and heat capacity are functions
of temperature and material states. The enthalpy technique, used for
the solution of phase change problems, has been used in an explicit
finite volume form for the hyperbolic heat transfer equation. This
technique has been used to calculate the transient temperature
distribution in the semi-infinite body and the growth rate of the melt
pool. In order to validate the numerical results, comparisons were
made with experimental data. Finally, the results of this paper were
compared with similar problem that has used the Fourier theory. The
comparison shows the influence of infinite speed of heat propagation
in Fourier theory on the temperature distribution and the melt pool
size.
Abstract: Dill (Anethum graveolens L.) is a popular herb used in
many regions, including Baltic countries. Dill is widely used for
flavoring foods and beverages due to its pleasant spicy aroma. The
aim of this work was to determine the best blanching method for
processing of dill prior to microwave vacuum drying based on
sensory properties, color and volatile compounds in dried product.
Two blanching mediums were used – water and steam, and for part of
samples microwave pretreatment was additionally used. Evaluation of
dried dill volatile aroma compounds, color changes and sensory
attributes was performed. Results showed that blanching significantly
influences the quality of dried dill. After evaluation of volatile aroma
compounds, color and sensory properties of microwave vacuum dried
dill, as the best method for dill pretreatment was established
blanching at 90 °C for 30 s.
Abstract: In this paper we present our results on the performance analysis of a multi-product manufacturing line. We study the influence of external perturbations, intermediate buffer content and the number of manufacturing stages on the production tracking error of each machine in the multi-product line operated under a surplusbased production control policy. Starting by the analysis of a single machine with multiple production stages (one for each product type), we provide bounds on the production error of each stage. Then, we extend our analysis to a line of multi-stage machines, where similarly, bounds on each production tracking error for each product type, as well as buffer content are obtained. Details on performance of the closed-loop flow line model are illustrated in numerical simulations.
Abstract: This paper presents a new and efficient approach for
capacitor placement in radial distribution systems that determine
the optimal locations and size of capacitor with an objective of
improving the voltage profile and reduction of power loss. The
solution methodology has two parts: in part one the loss sensitivity
factors are used to select the candidate locations for the capacitor
placement and in part two a new algorithm that employs Plant growth
Simulation Algorithm (PGSA) is used to estimate the optimal size
of capacitors at the optimal buses determined in part one. The main
advantage of the proposed method is that it does not require any
external control parameters. The other advantage is that it handles the
objective function and the constraints separately, avoiding the trouble
to determine the barrier factors. The proposed method is applied to 9
and 34 bus radial distribution systems. The solutions obtained by the
proposed method are compared with other methods. The proposed
method has outperformed the other methods in terms of the quality
of solution.
Abstract: The determination of sugars in foods is very
significant. Their relation in fact, can affect the chemical and
sensorial quality of the matrix (e.g., sweetness, pH, total acidity,
microbial stability, global acceptability) and can provide information
on food to optimize several selected technological processes. Three
stages of ripeness (green, yellow and red) of tomatoes (Lycopersicon
Esculentum cv. Elegance) at different harvest dates were evaluated.
Fruit from all harvests were exposed to different of ozone doses
(0.25, 0.50 and 1 mg O3/g tomatoes) and clean air for 5 day at 15
°C±2 and 90-95 % relative humidity. Then, fruits were submitted for
extraction and analysis after a day from the finish of exposure of each
stage. The concentrations of the glucose and fructose increased in the
tomatoes which were subjected to ozone treatments.
Abstract: The objective of this research was to study the career
success and the satisfaction of female executives working for schools
in Bangkok, Thailand. This paper drew upon the survey data
collected from 68 female executives. The survey conducted in on
Bangkok schools. The statistics utilized in this paper included
percentage, mean, standard deviation as well as t-test. The findings
revealed that the majority of samples had more than 30 years of
experience, held a master degree, and had an average income of less
than 40,000 baht. The majority of respondents worked not more than
50 hours per week. In addition, the mean score revealed career
development was ranked as their number one career satisfaction and
having a job related to education was ranked as their number one job
satisfaction. Also, the mean score of all categories of satisfaction was
4.61 with standard deviation of 1.677 which indicated that female
executive level of satisfaction was high. In terms of the subjectivity
career success, the hypothesis testing’s result disclosed that female
executives with different married status had a difference in their job
satisfaction which was significant at the 0.05 confidence level.