Abstract: Fast speed drives for Permanent Magnet Synchronous
Motor (PMSM) is a crucial performance for the electric traction
systems. In this paper, PMSM is derived with a Model-based
Predictive Control (MPC) technique. Fast speed tracking is achieved
through optimization of the DC source utilization using MPC. The
technique is based on predicting the optimum voltage vector applied
to the driver. Control technique is investigated by comparing to the
cascaded PI control based on Space Vector Pulse Width Modulation
(SVPWM). MPC and SVPWM-based FOC are implemented with the
TMS320F2812 DSP and its power driver circuits. The designed MPC
for a PMSM drive is experimentally validated on a laboratory test
bench. The performances are compared with those obtained by a
conventional PI-based system in order to highlight the improvements,
especially regarding speed tracking response.
Abstract: To mitigate the urban heat island effect has become a
global issue when we are faced with the challenge of climate change.
Through literature review, plant photosynthesis can reduce the carbon
dioxide and mitigate the urban heat island effect to a degree. Because
there are not enough open space and parks, green roof has become an
important policy in Taiwan.
We selected elementary school buildings in northern New Taipei
City as research subjects since elementary schools are asked with
priority to build green roof and important educational place to promote
green roof concept. Testo175-H1 recording device was used to record
the temperature and humidity differences between roof surface and
interior space below roof with and without green roof in the long-term.
We also use questionnaires to investigate the awareness of comfort
level of green roof and sensation of teachers and students of the
elementary schools.
The results indicated that the temperature of roof without greening
was higher than that with greening by about 2°C. But sometimes
during noontime, the temperature of green roof was higher than that of
non-green roof probably because of the character of the accumulation
and dissipation of heat of greening. The temperature of the interior
space below green roof was normally lower than that without green
roof by about 1°C, showing that green roof could lower the
temperature. The humidity of the green roof was higher than the one
without greening also indicated that green roof retained water better.
Teachers liked to combine green roof concept in the curriculum,
and students wished all classes can take turns to maintain the green
roof. Teachers and students whose school had integrated green roof
concept in the curriculum were more willing to participate in the
maintenance work of green roof. Teachers and students who may have
access to and touch the green roof can be more aware of the green roof
benefit. We suggest architects to increase the accessibility and
visibility of green roof, such as use it as a part of the activity space.
This idea can be a reference to the green roof curriculum design.
Abstract: Among various active filters, shunt active filter is a
viable solution for reactive power and harmonics compensation. In
this paper, the SRF plan is used to generate current reference for
compensation and conventional PI controllers were used as the
controller to compensate the reactive power. The design of the closed
loop controllers is reserved simple by modeling them as first order
systems. Computationally uncomplicated and efficient SVM system
is used in the present work for better utilization of dc bus voltage.
The rating of shunt active filter has been finalized based on the
reactive power demand of the selected reactive load. The proposed
control and SVM technique are validated by simulating in MATLAB
software.
Abstract: For the music composer Myriam Marbe the musical
time and memory represent 2 (complementary) phenomena with
conclusive impact on the settlement of new musical ontologies.
Summarizing the most important achievements of the contemporary
techniques of composition, her vision on the microform presented in
The Concert for Daniel Kientzy, saxophone and orchestra transcends
the linear and unidirectional time in favour of a flexible, multivectorial
speech with spiral developments, where the sound substance
is auto(re)generated by analogy with the fundamental processes of
the memory. The conceptual model is of an archetypal essence, the
music composer being concerned with identifying the mechanisms of
the creation process, especially of those specific to the collective
creation (of oral tradition). Hence the spontaneity of expression,
improvisation tint, free rhythm, micro-interval intonation, coloristictimbral
universe dominated by multiphonics and unique sound
effects, hence the atmosphere of ritual, however purged by the
primary connotations and reprojected into a wonderful spectacular
space. The Concert is a work of artistic maturity and enforces respect,
among others, by the timbral diversity of the three species of
saxophone required by the music composer (baritone, sopranino and
alt), in Part III Daniel Kientzy shows the performance of playing two
saxophones concomitantly. The score of the music composer Myriam
Marbe contains a deeply spiritualized music, full or archetypal
symbols, a music whose drama suggests a real cinematographic
movement.
Abstract: This paper deals with the study of reflection and
transmission characteristics of acoustic waves at the interface of a
semiconductor half-space and elastic solid. The amplitude ratios
(reflection and transmission coefficients) of reflected and transmitted
waves to that of incident wave varying with the incident angles have
been examined for the case of quasi-longitudinal wave. The special
cases of normal and grazing incidence have also been derived with
the help of Gauss elimination method. The mathematical model
consisting of governing partial differential equations of motion and
charge carriers’ diffusion of n-type semiconductors and elastic solid
has been solved both analytically and numerically in the study. The
numerical computations of reflection and transmission coefficients
has been carried out by using MATLAB programming software for
silicon (Si) semiconductor and copper elastic solid. The computer
simulated results have been plotted graphically for Si
semiconductors. The study may be useful in semiconductors,
geology, and seismology in addition to surface acoustic wave (SAW)
devices.
Abstract: Driver fatigue is an important factor in the increasing
number of road accidents. Dynamic template matching method was
proposed to address the problem of real-time driver fatigue detection
system based on eye-tracking. An effective vision based approach
was used to analyze the driver’s eye state to detect fatigue. The driver
fatigue system consists of Face detection, Eye detection, Eye
tracking, and Fatigue detection. Initially frames are captured from a
color video in a car dashboard and transformed from RGB into YCbCr
color space to detect the driver’s face. Canny edge operator was used
to estimating the eye region and the locations of eyes are extracted.
The extracted eyes were considered as a template matching for eye
tracking. Edge Map Overlapping (EMO) and Edge Pixel Count
(EPC) matching function were used for eye tracking which is used to
improve the matching accuracy. The pixel of eyeball was tracked
from the eye regions which are used to determine the fatigue state of
the driver.
Abstract: The objective of this study is to conduct computational
fluid dynamic (CFD) simulations for evaluating the cooling efficacy
from vegetation implanted in a public park in the Taipei, Taiwan. To
probe the impacts of park renewal by means of adding three pavilions
and supplementary green areas on urban microclimates, the simulated
results have revealed that the park having a higher percentage of green
coverage ratio (GCR) tended to experience a better cooling effect.
These findings can be used to explore the effects of different greening
modifications on urban environments for achieving an effective
thermal comfort in urban public spaces.
Abstract: To ensure student success in a non-majors biology course, a flipped classroom pedagogical approach was developed and implemented. All students were assigned online lectures to listen to before they come to class. A three hour lecture was split into one hour of online component, one hour of in class lecture and one hour of worksheets done by students in the classroom. This deviation from a traditional 3 hour in class lecture has resulted in increased student interest in science as well as better understanding of difficult scientific concepts. A pre and post survey was given to measure the interest in the subject and grades were used to measure the success rates. While the overall grade average did not change dramatically, students reported a much better appreciation of biology. Also, students overwhelmingly like the use of worksheets in class to help them understand the concepts. They liked the fact that they could listen to lectures at their own pace on line and even repeat if needed. The flipped classroom approach turned out to work really well our non-science majors and the author is ready to implement this in other classrooms.
Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: The Orthogonal Frequency Division Multiplexing
(OFDM) with high data rate, high spectral efficiency and its ability to
mitigate the effects of multipath makes them most suitable in wireless
application. Impulsive noise distorts the OFDM transmission and
therefore methods must be investigated to suppress this noise. In this
paper, a State Space Recursive Least Square (SSRLS) algorithm
based adaptive impulsive noise suppressor for OFDM
communication system is proposed. And a comparison with another
adaptive algorithm is conducted. The state space model-dependent
recursive parameters of proposed scheme enables to achieve steady
state mean squared error (MSE), low bit error rate (BER), and faster
convergence than that of some of existing algorithm.
Abstract: Diagram and drawing are important ways to
communicate and the reproduce of architectural design, Due to the
development of information and communication technology, the
professional thinking of architecture and interior design are also
change rapidly. In development process of design, diagram always
play very important role. This study is based on diagram theories,
observe and record interaction between man and objects, objects and
space, and space and time in a modern nuclear family. Construct a
method for diagram to systematically and visualized describe the
space plan of a modern nuclear family toward an intelligent design, to
assist designer to retrieve information and review event pattern of past
and present.
Abstract: A simple adaptive voice activity detector (VAD) is
implemented using Gabor and gammatone atomic decomposition of
speech for high Gaussian noise environments. Matching pursuit is
used for atomic decomposition, and is shown to achieve optimal
speech detection capability at high data compression rates for low
signal to noise ratios. The most active dictionary elements found by
matching pursuit are used for the signal reconstruction so that the
algorithm adapts to the individual speakers dominant time-frequency
characteristics. Speech has a high peak to average ratio enabling
matching pursuit greedy heuristic of highest inner products to isolate
high energy speech components in high noise environments. Gabor
and gammatone atoms are both investigated with identical
logarithmically spaced center frequencies, and similar bandwidths.
The algorithm performs equally well for both Gabor and gammatone
atoms with no significant statistical differences. The algorithm
achieves 70% accuracy at a 0 dB SNR, 90% accuracy at a 5 dB SNR
and 98% accuracy at a 20dB SNR using 30d B SNR as a reference
for voice activity.
Abstract: This work studied the isomerization of 1-butene over
hydrotalcite catalyst. The experiments were conducted at various gas
hourly space velocity (GHSV), reaction temperature and feed
concentration. No catalyst deactivation was observed over the
reaction time of 16 hours. Two major reaction products were trans-2-
butene and cis-2-butene. The reaction temperature played an
important role on the reaction selectivity. At high operating
temperatures, the selectivity of trans-2-butene was higher than the
selectivity of cis-2-butene while it was opposite at lower reaction
temperature. In the range of operating condition, the maximum
conversion of 1-butene was found at 74% when T = 673 K and GHSV
= 4 m3/h/kg-cat with trans- and cis-2-butene selectivities of 54% and
46%, respectively. Finally, the kinetic parameters of the reaction
were determined.
Abstract: This paper deals with various questions related to
functionality and providing banking services in the European union
on the Internet. Due to the fact that we live in the information
technologies era, the Internet become a new space for doing
economic and business activities in all areas, and especially important
in banking. Accepting the busy tempo of life, in the past several years
electronic banking has become necessity and a must for most users of
banking services. On a sample of 300 web sites of the banks
operating in European Union (EU) we conduct the research on the
functionality of e-banking services offered through banks web sites
with the key objective to reveal to what extent the information
technologies are used in their business operations. Characteristics of
EU banks websites will be examined and compared to the basic
groups of business activities on the web. Also some
recommendations for the successful bank web sites will be provided.
Abstract: In order to avoid self-collision of space manipulators
during operation process, a real-time detection method is proposed in
this paper. The manipulator is fitted into a cylinder-enveloping
surface, and then, a kind of detection algorithm of collision between
cylinders is analyzed. The collision model of space manipulator
self-links can be detected by using this algorithm in real-time detection
during the operation process. To ensure security of the operation, a
safety threshold is designed. The simulation and experiment results
verify the effectiveness of the proposed algorithm for a 7-DOF space
manipulator.
Abstract: In this research numerical simulations are performed,
using the multi-relaxation-time lattice Boltzmann method, in the
range 3 ≤ β = w[d] ≤ 30 at Re = 100, 200 and 300, where β the
blockage ratio, w is the equispaced distance between centers of
cylinders, d is the diameter of the cylinder and Re is the Reynolds
number, respectively. Special attention is paid to the effect of the
equispaced distance between centers of cylinders. Visualization of
the vorticity contour visualization are presented for some simulation
showing the flow dynamics and patterns for blockage effect. Results
show that the drag and mean drag coefficients, and Strouhal number,
in general, decrease with the increase of β for fixed Re. It is found
that the decreasing rate of drag and mean drag coefficients and
Strouhal number is more distinct in the range 3 ≤ β ≤ 15. We found
that when β > 15, the blockage effect almost diminishes. Our results
further indicate that the drag and mean drag coefficients, peak value
of the lift coefficient, root-mean-square value of the lift and drag
coefficients and the ratio between lift and drag coefficients decrease
with the increase of Re. The results indicate that symmetry boundary
condition have more blockage effect as compared to periodic
boundary condition.
Abstract: Roadway planning and design is a very complex
process involving five key phases before a project is completed;
planning, project development, final design, right-of-way, and
construction. The planning phase for a new roadway transportation
project is a very critical phase as it greatly affects all latter phases of
the project. A location study is usually performed during the
preliminary planning phase in a new roadway project. The objective
of the location study is to develop alignment alternatives that are cost
efficient considering land acquisition and construction costs. This
paper describes a methodology to develop optimal preliminary
roadway alignments utilizing spatial-data. Four optimization criteria
are taken into consideration; roadway length, land cost, land slope,
and environmental impacts. The basic concept of the methodology is
to convert the proposed project area into a grid, which represents the
search space for an optimal alignment. The aforementioned
optimization criteria are represented in each of the grid’s cells. A
spatial-data optimization technique is utilized to find the optimal
alignment in the search space based on the four optimization criteria.
Two case studies for new roadway projects in Duval County in the
State of Florida are presented to illustrate the methodology. The
optimization output alignments are compared to the proposed Florida
Department of Transportation (FDOT) alignments. The comparison is
based on right-of-way costs for the alignments. For both case studies,
the right-of-way costs for the developed optimal alignments were
found to be significantly lower than the FDOT alignments.
Abstract: The structures obtained with the use of sandwich
technologies combine low weight with high energy absorbing
capacity and load carrying capacity. Hence, there is a growing and
markedly interest in the use of sandwiches with aluminum foam core
because of very good properties such as flexural rigidity and energy
absorption capability. In the current investigation, the static threepoint
bending tests were carried out on the sandwiches with
aluminum foam core and glass fiber reinforced polymer (GFRP)
skins at different values of support span distances aiming the analyses
of their flexural performance. The influence of the core thickness and
the GFRP skin type was reported in terms of peak load and energy
absorption capacity. For this purpose, the skins with two different
types of fabrics which have same thickness value and the aluminum
foam core with two different thicknesses were bonded with a
commercial polyurethane based flexible adhesive in order to combine
the composite sandwich panels. The main results of the bending tests
are: force-displacement curves, peak force values, absorbed energy,
collapse mechanisms and the effect of the support span length and
core thickness. The results of the experimental study showed that the
sandwich with the skins made of S-Glass Woven fabrics and with the
thicker foam core presented higher mechanical values such as load
carrying and energy absorption capacities. The increment of the
support span distance generated the decrease of the mechanical
values for each type of panels, as expected, because of the inverse
proportion between the force and span length. The most common
failure types of the sandwiches are debonding of the lower skin and
the core shear. The obtained results have particular importance for
applications that require lightweight structures with a high capacity
of energy dissipation, such as the transport industry (automotive,
aerospace, shipbuilding and marine industry), where the problems of
collision and crash have increased in the last years.
Abstract: Latin hypercube designs (LHDs) have been applied in
many computer experiments among the space-filling designs found in
the literature. A LHD can be randomly generated but a randomly
chosen LHD may have bad properties and thus act poorly in
estimation and prediction. There is a connection between Latin
squares and orthogonal arrays (OAs). A Latin square of order s
involves an arrangement of s symbols in s rows and s columns, such
that every symbol occurs once in each row and once in each column
and this exists for every non-negative integer s. In this paper, a
computer program was written to construct orthogonal array-based
Latin hypercube designs (OA-LHDs). Orthogonal arrays (OAs) were
constructed from Latin square of order s and the OAs constructed
were afterward used to construct the desired Latin hypercube designs
for three input variables for use in computer experiments. The LHDs
constructed have better space-filling properties and they can be used
in computer experiments that involve only three input factors.
MATLAB 2012a computer package (www.mathworks.com/) was
used for the development of the program that constructs the designs.
Abstract: This work sets out to debate the tensions involved in
the processes of contamination and self-purification in the urban
space, particularly in the streams that run through the Buenos Aires
metropolitan area. For much of their course, those streams are piped;
their waters do not come into contact with the outdoors until they
have reached deeply impoverished urban areas with high levels of
environmental contamination. These are peripheral zones that, until
thirty years ago, were marshlands and fields. They are now densely
populated areas largely lacking in urban infrastructure.
The Cárcova neighborhood, where this project is underway, is in
the José León Suárez section of General San Martín county, Buenos
Aires province. A stretch of José León Suarez canal crosses the
neighborhood. Starting upstream, this canal carries pollutants due to
the sewage and industrial waste released into it. Further downstream,
in the neighborhood, domestic drainage is poured into the stream. In
this paper, we formulate a hypothesis diametrical to the one that
holds that these neighborhoods are the primary source of
contamination, suggesting instead that in the stretch of the canal that
runs through the neighborhood the stream’s waters are actually
cleaned and the sediments accumulate pollutants. Indeed, the
stretches of water that runs through these neighborhoods act as water
processing plants for the metropolis.
This project has studied the different organic-load polluting
contributions to the water in a certain stretch of the canal, the
reduction of that load over the course of the canal, and the
incorporation of pollutants into the sediments. We have found that
the surface water has considerable ability to self-purify, mostly due to
processes of sedimentation and adsorption. The polluting load is
accumulated in the sediments where that load stabilizes slowly by
means of anaerobic processes. In this study, we also investigated the
risks of sediment management and the use of the processes studied
here in controlled conditions as tools of environmental restoration.