Abstract: In this research, heat transfer of a poly Ethylene
fluidized bed reactor without reaction were studied experimentally
and computationally at different superficial gas velocities. A multifluid
Eulerian computational model incorporating the kinetic theory
for solid particles was developed and used to simulate the heat
conducting gas–solid flows in a fluidized bed configuration.
Momentum exchange coefficients were evaluated using the Syamlal–
O-Brien drag functions. Temperature distributions of different phases
in the reactor were also computed. Good agreement was found
between the model predictions and the experimentally obtained data
for the bed expansion ratio as well as the qualitative gas–solid flow
patterns. The simulation and experimental results showed that the gas
temperature decreases as it moves upward in the reactor, while the
solid particle temperature increases. Pressure drop and temperature
distribution predicted by the simulations were in good agreement
with the experimental measurements at superficial gas velocities
higher than the minimum fluidization velocity. Also, the predicted
time-average local voidage profiles were in reasonable agreement
with the experimental results. The study showed that the
computational model was capable of predicting the heat transfer and
the hydrodynamic behavior of gas-solid fluidized bed flows with
reasonable accuracy.
Abstract: When acid is pumped into damaged reservoirs for
damage removal/stimulation, distorted inflow of acid into the
formation occurs caused by acid preferentially traveling into highly
permeable regions over low permeable regions, or (in general) into
the path of least resistance. This can lead to poor zonal coverage and
hence warrants diversion to carry out an effective placement of acid.
Diversion is desirably a reversible technique of temporarily reducing
the permeability of high perm zones, thereby forcing the acid into
lower perm zones.
The uniqueness of each reservoir can pose several challenges to
engineers attempting to devise optimum and effective diversion
strategies. Diversion techniques include mechanical placement and/or
chemical diversion of treatment fluids, further sub-classified into ball
sealers, bridge plugs, packers, particulate diverters, viscous gels,
crosslinked gels, relative permeability modifiers (RPMs), foams,
and/or the use of placement techniques, such as coiled tubing (CT)
and the maximum pressure difference and injection rate (MAPDIR)
methodology.
It is not always realized that the effectiveness of diverters greatly
depends on reservoir properties, such as formation type, temperature,
reservoir permeability, heterogeneity, and physical well
characteristics (e.g., completion type, well deviation, length of
treatment interval, multiple intervals, etc.). This paper reviews the
mechanisms by which each variety of diverter functions and
discusses the effect of various reservoir properties on the efficiency
of diversion techniques. Guidelines are recommended to help
enhance productivity from zones of interest by choosing the best
methods of diversion while pumping an optimized amount of
treatment fluid. The success of an overall acid treatment often
depends on the effectiveness of the diverting agents.
Abstract: The objectif of the present work is to determinate the
potential of the solar parabolic trough collector (PTC) for use in the
design of a solar thermal power plant in Algeria. The study is based
on a mathematical modeling of the PTC. Heat balance has been
established respectively on the heat transfer fluid (HTF), the absorber
tube and the glass envelop using the principle of energy conservation
at each surface of the HCE cross-sectionn. The modified Euler
method is used to solve the obtained differential equations. At first
the results for typical days of two seasons the thermal behavior of the
HTF, the absorber and the envelope are obtained. Then to determine
the thermal performances of the heat transfer fluid, different oils are
considered and their temperature and heat gain evolutions compared.
Abstract: The objectives of this research paper were to study the
influencing factors that contributed to the success of electronic
commerce (e-commerce) and to study the approach to enhance the
standard of e-commerce for small and medium enterprises (SME).
The research paper focused the study on only sole proprietorship
SMEs in Bangkok, Thailand. The factors contributed to the success
of SME included business management, learning in the organization,
business collaboration, and the quality of website. A quantitative and
qualitative mixed research methodology was used. In terms of
quantitative method, a questionnaire was used to collect data from
251 sole proprietorships. The System Equation Model (SEM) was
utilized as the tool for data analysis. In terms of qualitative method,
an in-depth interview, a dialogue with experts in the field of ecommerce
for SMEs, and content analysis were used.
By using the adjusted causal relationship structure model, it was
revealed that the factors affecting the success of e-commerce for
SMEs were found to be congruent with the empirical data. The
hypothesis testing indicated that business management influenced the
learning in the organization, the learning in the organization
influenced business collaboration and the quality of the website, and
these factors, in turn, influenced the success of SMEs. Moreover, the
approach to enhance the standard of SMEs revealed that the majority
of respondents wanted to enhance the standard of SMEs to a high
level in the category of safety of e-commerce system, basic structure
of e-commerce, development of staff potentials, assistance of budget
and tax reduction, and law improvement regarding the e-commerce
respectively.
Abstract: This research paper deals with the implementation of face recognition using neural network (recognition classifier) on low-resolution images. The proposed system contains two parts, preprocessing and face classification. The preprocessing part converts original images into blurry image using average filter and equalizes the histogram of those image (lighting normalization). The bi-cubic interpolation function is applied onto equalized image to get resized image. The resized image is actually low-resolution image providing faster processing for training and testing. The preprocessed image becomes the input to neural network classifier, which uses back-propagation algorithm to recognize the familiar faces. The crux of proposed algorithm is its beauty to use single neural network as classifier, which produces straightforward approach towards face recognition. The single neural network consists of three layers with Log sigmoid, Hyperbolic tangent sigmoid and Linear transfer function respectively. The training function, which is incorporated in our work, is Gradient descent with momentum (adaptive learning rate) back propagation. The proposed algorithm was trained on ORL (Olivetti Research Laboratory) database with 5 training images. The empirical results provide the accuracy of 94.50%, 93.00% and 90.25% for 20, 30 and 40 subjects respectively, with time delay of 0.0934 sec per image.
Abstract: X-ray mammography is the most effective method for
the early detection of breast diseases. However, the typical diagnostic
signs such as microcalcifications and masses are difficult to detect
because mammograms are of low-contrast and noisy. In this paper, a
new algorithm for image denoising and enhancement in Orthogonal
Polynomials Transformation (OPT) is proposed for radiologists to
screen mammograms. In this method, a set of OPT edge coefficients
are scaled to a new set by a scale factor called OPT scale factor. The
new set of coefficients is then inverse transformed resulting in
contrast improved image. Applications of the proposed method to
mammograms with subtle lesions are shown. To validate the
effectiveness of the proposed method, we compare the results to
those obtained by the Histogram Equalization (HE) and the Unsharp
Masking (UM) methods. Our preliminary results strongly suggest
that the proposed method offers considerably improved enhancement
capability over the HE and UM methods.
Abstract: Interactions among proteins are the basis of various
life events. So, it is important to recognize and research protein
interaction sites. A control set that contains 149 protein molecules
were used here. Then 10 features were extracted and 4 sample sets
that contained 9 sliding windows were made according to features.
These 4 sample sets were calculated by Radial Basis Functional neutral
networks which were optimized by Particle Swarm Optimization
respectively. Then 4 groups of results were obtained. Finally, these 4
groups of results were integrated by decision fusion (DF) and Genetic
Algorithm based Selected Ensemble (GASEN). A better accuracy was
got by DF and GASEN. So, the integrated methods were proved to
be effective.
Abstract: The improvement of a filer case utilized to purify the
let-out smoke and smell in the production of Benjarong Ceramic is
studied through Participatory Action Research (PAR). This research
is aimed to protect smell, dirty smoke, and air pollution which are
effects of incomplete combustion in the production of Benjarong
ceramic. This research was conducted at Jongjint Benjarong Ceramic
Factory in Plai Bang, Bang Kruai, Nonthaburi Province,Thailand,
also 12 employees were interviewed for data collection. All collected
data were analyzed to develop and create solution to protect smoke
and smell pollution from Benjarong ceramic production.
The results revealed that the employees who have used the
developed filer cases are moderately satisfied. In addition to the
efficiency of developed smoke-and-smell filer cases, it was found
that Overall, the respondents were satisfied moderately with
efficiency of modified smoke and smell filter cases.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: In recent years, sustainable supply chain management
(SSCM) has been widely researched in academic domain. However,
due to the traditional operational role and the complexity of supply
chain management in the cement industry, a relatively small amount
of research has been conducted on cement supply chain simulation
integrated with sustainability criteria. This paper analyses the cement
supply chain operations using the Push-Pull supply chain
frameworks, the Life Cycle Assessment (LCA) methodology; and
proposal integration approach, proposes three supply chain scenarios
based on Make-To-Stock (MTS), Pack-To-Order (PTO) and Grind-
To-Order (GTO) strategies. A Discrete-Event Simulation (DES)
model of SSCM is constructed using Arena software to implement
the three-target scenarios. We conclude with the simulation results
that (GTO) is the optimal supply chain strategy that demonstrates the
best economic, ecological and social performance in the cement
industry.
Abstract: Because of increasing demands for security in today-s
society and also due to paying much more attention to machine
vision, biometric researches, pattern recognition and data retrieval in
color images, face detection has got more application. In this article
we present a scientific approach for modeling human skin color, and
also offer an algorithm that tries to detect faces within color images
by combination of skin features and determined threshold in the
model. Proposed model is based on statistical data in different color
spaces. Offered algorithm, using some specified color threshold, first,
divides image pixels into two groups: skin pixel group and non-skin
pixel group and then based on some geometric features of face
decides which area belongs to face.
Two main results that we received from this research are as follow:
first, proposed model can be applied easily on different databases and
color spaces to establish proper threshold. Second, our algorithm can
adapt itself with runtime condition and its results demonstrate
desirable progress in comparison with similar cases.
Abstract: Since the feasibility study of R&D programs have been
initiated for efficient public R&D investments, year 2008, feasibility
studies have improved in terms of precision. Although experience
related to these studies of R&D programs have increased to a certain
point, still methodological improvement is required. The feasibility
studies of R&D programs are consisted of various viewpoints, such as
technology, policy, and economics. This research is to provide
improvement methods to the economic perspective; especially the cost
estimation process of R&D activities. First of all, the fundamental
concept of cost estimation is reviewed. After the review, a statistical
and econometric analysis method is applied as empirical analysis.
Conclusively, limitations and further research directions are provided.
Abstract: This study investigates the relationships between
Work Motivation, Work Stress, and Job Satisfaction toward
cross-strait employees. The target subjects are three
manufacturing firms in Mainland China and Taiwan. Out of 450
distributed surveys, 352 valid surveys were obtained with the
response rate of 78.22%.The findings have addressed three main
pull factors toward cross-strait employees in choosing jobs, which
are (1) high level of firm stability, (2) good firm image, and (3)
good employee benefits. In addition, various employee attributes
exert different impacts on Work Motivation, Work Stress, and
Job Satisfaction. The comparison between expected and actual
perceived Job Satisfaction toward cross-strait employees shows
that “salary" ranks highest regarding expected Job Satisfaction
whereas “co-worker relationship" ranks highest regarding actual
perceived Job Satisfaction, which implies actual perceived Job
Satisfaction do not match employee expectations. Therefore, this
research further concludes that there exists differences between
employees- expected and actual perceived Job Satisfaction.
Abstract: The data presented in this work show that in Armenia
a rise of air temperature is expected in the season, and annual terms.
As a result of the noted increase in temperature, a significant growth
of vulnerability of the territory of Armenia in relation to malaria is
expected. Zoning by the risk of renewed malaria transmission has
been performed.
Abstract: The sanitary sewerage connection rate becomes an
important indicator of advanced cities. Following the construction of
sanitary sewerages, the maintenance and management systems are
required for keeping pipelines and facilities functioning well. These
maintenance tasks often require sewer workers to enter the manholes
and the pipelines, which are confined spaces short of natural
ventilation and full of hazardous substances. Working in sewers could
be easily exposed to a risk of adverse health effects. This paper
proposes the use of Bayesian belief networks (BBN) as a higher level
of noncarcinogenic health risk assessment of sewer workers. On the
basis of the epidemiological studies, the actual hospital attendance
records and expert experiences, the BBN is capable of capturing the
probabilistic relationships between the hazardous substances in sewers
and their adverse health effects, and accordingly inferring the
morbidity and mortality of the adverse health effects. The provision of
the morbidity and mortality rates of the related diseases is more
informative and can alleviate the drawbacks of conventional methods.
Abstract: The Artificial immune systems algorithms are Meta
heuristic optimization method, which are used for clustering and
pattern recognition applications are abundantly. These algorithms in
multimodal optimization problems are more efficient than genetic
algorithms. A major drawback in these algorithms is their slow
convergence to global optimum and their weak stability can be
considered in various running of these algorithms. In this paper,
improved Artificial Immune System Algorithm is introduced for the
first time to overcome its problems of artificial immune system. That
use of the small size of a local search around the memory antibodies
is used for improving the algorithm efficiently. The credibility of the
proposed approach is evaluated by simulations, and it is shown that
the proposed approach achieves better results can be achieved
compared to the standard artificial immune system algorithms
Abstract: Exclusive breastfeeding is the feeding of a baby on no other milk apart from breast milk. Exclusive breastfeeding during the first 6 months of life is very important as it supports optimal growth and development during infancy and reduces the risk of obliterating diseases and problems. Moreover, it helps to reduce the incidence and/or severity of diarrhea, lower respiratory infection and urinary tract infection. In this paper, we make a survey of the factors that influence exclusive breastfeeding and use two dispersed statistical models to analyze data. The models are the Generalized Poisson regression model and the Com-Poisson regression models.
Abstract: Oxygen and carbon isotopes records of multi-species planktonic, benthic foraminifera and bulk carbonate sample from Central Java Indonesia demonstrate that warm sea surface temperature occurred during the Miocene. Planktonic δ18O values from this study consistently lighter (-4 to -3 ‰PDB) than previous studies that indicate sea surface temperature during Miocene in this area was warm than tropical/equatorial localities. A surprising decrease of oxygen isotopic composition was recorded at ±14 Ma where the maximum of δ18O values is -4.87 ‰PDB for Orbulina universa, -5.02 ‰PDB for Globigerinoides sacculifer and -4.30 ‰PDB for Globoquadrina dehiscens, this event we predict as Middle Miocene Optimum. Warming of sea surface temperature we interpret as related to the development of Western Pacific Warm Pool where warm water from Pacific Ocean through the Indonesian seaway appears to remain during Miocene. Our result also show increasing suddenly of oxygen isotope values of planktic, benthic and bulk carbonate sample from ± 12 Ma, the increasing cooled surface water relatively high degree with Late Miocene global cooling climate or we predict that due to closing of Indonesian Gateway.
Abstract: Access to information is the key to the empowerment of everybody despite where they are living. This research is to be carried out in respect of the people living in developing countries, considering their plight and complex geographical, demographic, social-economic conditions surrounding the areas they live, which hinder access to information and of professionals providing services such as medical workers, which has led to high death rates and development stagnation. Research on Unified Communications and Integrated Collaborations (UCIC) system in the health sector of developing countries comes in to create a possible solution of bridging the digital canyon among the communities. The aim is to deliver services in a seamless manner to assist health workers situated anywhere to be accessed easily and access information which will help in service delivery. The proposed UCIC provides the most immersive Telepresence experience for one-to-one or many-tomany meetings. Extending to locations anywhere in the world, the transformative platform delivers Ultra-low operating costs through the use of general purpose networks and using special lenses and track systems.
Abstract: The request for a sustainable development challenges
both managers and consumers to rethink habitual practices and
activities. While consumers are challenged to develop sustainable
consumption patterns, companies are asked to establish managerial
systems and structures considering economical, ecological, and social
issues. As this is in particular true for housing associations, this paper
aims first, at providing an understanding of sustainability strategy in
residential trade and industry (RTI) by identifying relevant facets of
this construct and second, at conceptually analyzing the impact of
sustainability strategy in RTI on operational efficiency and
performance of municipal housing companies. The author develops a
model of sustainability strategy in RTI and its effects and further,
sheds light in priorities for future research.