Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: In this paper, Speed Sensorless Indirect Field Oriented Control (IFOC) of a Permanent Magnet Synchronous machine (PMSM) is studied. The closed loop scheme of the drive system utilizes fuzzy speed and current controllers. Due to the well known drawbacks of the speed sensor, an algorithm is proposed in this paper to eliminate it. In fact, based on the model of the PMSM, the stator currents and rotor speed are estimated simultaneously using adaptive Luenberger observer for currents and MRAS (Model Reference Adaptive System) observer for rotor speed. To overcome the sensivity of this algorithm against parameter variation, adaptive for on line stator resistance tuning is proposed. The validity of the proposed method is verified by an extensive simulation work.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: In order to study the effect of plant density and
competition of wheat with field bindweed (Convolvulus arvensis) on
yield and agronomical properties of wheat(Triticum Sativum) in
irrigated conditions, a factorial experiment as the base of complete
randomize block design in three replication was conducted at the
field of Kamalvand in khoramabad (Lorestan) region of Iran during
2008-2009. Three plant density (Factor A=200, 230 and 260kg/ha)
three cultivar (Factor B=Bahar,Pishtaz and Alvand) and weed control
(Factor C= control and no control of weeds)were assigned in
experiment. Results show that: Plant density had significant effect
(statistically) on seed yield, 1000 seed weight, weed density and dry
weight of weeds, seed yield and harvest index had been meaningful
effect for cultivars. The interaction between plant density and
cultivars for weed density, seed yield, thousand seed weight and
harvest index were significant. 260 kg/ha (plant density) of wheat had
more effect on increasing of seed yield in Bahar cultivar wheat in
khoramabad region of Iran.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: In this article, the design of a Supply Chain Network
(SCN) consisting of several suppliers, production plants, distribution
centers and retailers, is considered. Demands of retailers are
considered stochastic parameters, so we generate amounts of data via
simulation to extract a few demand scenarios. Then a mixed integer
two-stage programming model is developed to optimize
simultaneously two objectives: (1) minimization the fixed and
variable cost, (2) maximization the service level. A weighting method
is utilized to solve this two objective problem and a numerical
example is made to show the performance of the model.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: This paper shows how we can integrate
communication modeling into the design modeling at early stages of
the design flow. We consider effect of incorporating noise such as
impulsive noise on system stability. We show that with change of the
system model and investigate the system performance under the
different communication effects. We modeled a unmanned aerial
vehicle (UAV) as a demonstration using SystemC methodology.
Moreover the system is modeled by joining the capabilities of UML
and SystemC to operate at system level.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: The research was conducted with three replications as
“Randomized Block Design” in Konya-Turkey ecological conditions.
In the study, 16 of promising safflower lines (A8, E1, F4, F6, G16,
H14, I1), and 1 cultivar (Dinçer) were evaluated in 2008-09 growing
season. Some of the yield components such as plant height (cm), first
branch height (cm), number of branches per plant, 1000 seed weight
(g), seed yield (kg ha-1), oil content (%), oil yield (kg ha-1) were
determined. Winter sowing showed higher values than spring sowing.
The highest values were taken from Dinçer for plant height (86.7
cm), E1 (37.5 cm) for first branch height, F6 for number of branch
(11.6 per plant), I1 for number of head (24.9 per plant), A8 for 1000
seed weight (51.75 g), Dinçer for seed yield (2927.1 kg ha-1), oil
content (28.79 %) and also for oil yield (87.44 kg ha-1) respectively.
Abstract: An adaptive Fuzzy Inference Perceptual model has
been proposed for watermarking of digital images. The model
depends on the human visual characteristics of image sub-regions in
the frequency multi-resolution wavelet domain. In the proposed
model, a multi-variable fuzzy based architecture has been designed to
produce a perceptual membership degree for both candidate
embedding sub-regions and strength watermark embedding factor.
Different sizes of benchmark images with different sizes of
watermarks have been applied on the model. Several experimental
attacks have been applied such as JPEG compression, noises and
rotation, to ensure the robustness of the scheme. In addition, the
model has been compared with different watermarking schemes. The
proposed model showed its robustness to attacks and at the same time
achieved a high level of imperceptibility.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: Due to the coexistence of different Radio Access
Technologies (RATs), Next Generation Wireless Networks (NGWN)
are predicted to be heterogeneous in nature. The coexistence of
different RATs requires a need for Common Radio Resource
Management (CRRM) to support the provision of Quality of Service
(QoS) and the efficient utilization of radio resources. RAT selection
algorithms are part of the CRRM algorithms. Simply, their role is to
verify if an incoming call will be suitable to fit into a heterogeneous
wireless network, and to decide which of the available RATs is most
suitable to fit the need of the incoming call and admit it.
Guaranteeing the requirements of QoS for all accepted calls and at
the same time being able to provide the most efficient utilization of
the available radio resources is the goal of RAT selection algorithm.
The normal call admission control algorithms are designed for
homogeneous wireless networks and they do not provide a solution
to fit a heterogeneous wireless network which represents the NGWN.
Therefore, there is a need to develop RAT selection algorithm for
heterogeneous wireless network. In this paper, we propose an
approach for RAT selection which includes receiving different
criteria, assessing and making decisions, then selecting the most
suitable RAT for incoming calls. A comprehensive survey of
different RAT selection algorithms for a heterogeneous wireless
network is studied.
Abstract: terrorism and extremism are among the most
dangerous and difficult to forecast the phenomena of our time, which
are becoming more diverse forms and rampant. Terrorist attacks often
produce mass casualties, involve the destruction of material and
spiritual values, beyond the recovery times, sow hatred among
nations, provoke war, mistrust and hatred between the social and
national groups, which sometimes can not be overcome within a
generation. Currently, the countries of Central Asia are a topical issue
– the threat of terrorism and religious extremism, which grow not
only in our area, but throughout the world. Of course, in each of the
terrorist threat is assessed differently. In our country the problem of
terrorism should not be acutely. Thus, after independence and
sovereignty of Kazakhstan has chosen the path of democracy,
progress and free economy. With the policy of the President of
Kazakhstan Nursultan Nazarbayev and well-organized political and
economic reforms, there has been economic growth and rising living
standards, socio-political stability, ensured civil peace and accord in
society [1].
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: An experiment was conducted in October 2008 due the ability replacement plant associate biofertilizers by chemical fertilizers and the qualifying rate of chemical N fertilizers at the moment of using this biofertilizers and the interaction of this biofertilizer on each other. This field experiment has been done in Persepolis (Throne of Jamshid) and arrange by using factorial with the basis of randomized complete block design, in three replication Azespirilium SP bacteria has been admixed with consistence 108 cfu/g and inoculated with seeds of wheat, The streptomyces SP has been used in amount of 550 gr/ha and concatenated on clay and for the qualifying range of chemical fertilizer 4 level of N chemical fertilizer from the source of urea (N0=0, N1=60, N2=120, N3=180) has been used in this experiment. The results indicated there were Significant differences between levels of Nitrogen fertilizer in the entire characteristic which has been measured in this experiment. The admixed Azespirilium SP showed significant differences between their levels in the characteristics such as No. of fertile ear, No. of grain per ear, grain yield, grain protein percentage, leaf area index and the agronomic fertilizer use efficiency. Due the interaction streptomyses with Azespirilium SP bacteria this actinomycet didn-t show any statistically significant differences between it levels.
Abstract: One of the most important aspects expected from an
ERP system is to mange user\administrator manual documents
dynamically. Since an ERP package is frequently changed during its
implementation in customer sites, it is often needed to add new
documents and/or apply required changes to existing documents in
order to cover new or changed capabilities. The worse is that since
these changes occur continuously, the corresponding documents
should be updated dynamically; otherwise, implementing the ERP
package in the organization encounters serious risks. In this paper, we
propose a new architecture which is based on the agent oriented
vision and supplies the dynamic document generation expected from
ERP systems using several independent but cooperative agents.
Beside the dynamic document generation which is the main issue of
this paper, the presented architecture will address some aspects of
intelligence and learning capabilities existing in ERP.