Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: The growing number of computer viruses and the
detection of zero day malware have been the concern for security
researchers for a large period of time. Existing antivirus products
(AVs) rely on detecting virus signatures which do not provide a full
solution to the problems associated with these viruses. The use of
logic formulae to model the behaviour of viruses is one of the most
encouraging recent developments in virus research, which provides
alternatives to classic virus detection methods. In this paper, we
proposed a comparative study about different virus detection
techniques. This paper provides the advantages and drawbacks of
different detection techniques. Different techniques will be used in
this paper to provide a discussion about what technique is more
effective to detect computer viruses.
Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: In this article, a new method is proposed for the measuring of well-being inequality through a model composed of superimposing satisfaction waves. The displacement of households’ satisfactory state (i.e. satisfaction) is defined in a satisfaction string. The duration of the satisfactory state for a given period is measured in order to determine the relationship between utility and total satisfactory time, itself dependent on the density and tension of each satisfaction string. Thus, individual cardinal total satisfaction values are computed by way of a one-dimensional form for scalar sinusoidal (harmonic) moving wave function, using satisfaction waves with varying amplitudes and frequencies which allow us to measure wellbeing inequality. One advantage to using satisfaction waves is the ability to show that individual utility and consumption amounts would probably not commute; hence, it is impossible to measure or to know simultaneously the values of these observables from the dataset. Thus, we crystallize the problem by using a Heisenberg-type uncertainty resolution for self-adjoint economic operators. We propose to eliminate any estimation bias by correlating the standard deviations of selected economic operators; this is achieved by replacing the aforementioned observed uncertainties with households’ perceived uncertainties (i.e. corrected standard deviations) obtained through the logarithmic psychophysical law proposed by Weber and Fechner.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: In the present paper the design of plate heat exchangers
is formulated as an optimization problem considering two
mathematical modelling. The number of plates is the objective
function to be minimized, considering implicitly some parameters
configuration. Screening is the optimization method used to solve the
problem. Thermal and hydraulic constraints are verified, not viable
solutions are discarded and the method searches for the convergence to
the optimum, case it exists. A case study is presented to test the
applicability of the developed algorithm. Results show coherency with
the literature.
Abstract: The access to relevant information that is adapted to
user’s needs, preferences and environment is a challenge in many
applications running. That causes an appearance of context-aware
systems. To facilitate the development of this class of applications, it
is necessary that these applications share a common context
metamodel. In this article, we will present our context metamodel
that is defined using the OMG Meta Object facility (MOF).This
metamodel is based on the analysis and synthesis of context concepts
proposed in literature.
Abstract: Mobile Ad Hoc Networks (MANETs) is a collection
of mobile devices forming a communication network without
infrastructure. MANET is vulnerable to security threats due to
network’s limited security, dynamic topology, scalability and the lack
of central management. The Quality of Service (QoS) routing in such
networks is limited by network breakage caused by node mobility or
nodes energy depletions. The impact of node mobility on trust
establishment is considered and its use to propagate trust through a
network is investigated in this paper. This work proposes an
enhanced Associativity Based Routing (ABR) with Fuzzy based
Trust (Fuzzy- ABR) routing protocol for MANET to improve QoS
and to mitigate network attacks.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: Traditional mechanical control systems in thrust
vectoring are efficient in rocket thrust guidance but their costs
and their weights are excessive. The fluidic injection in the nozzle
divergent constitutes an alternative procedure to achieve the goal. In
this paper, we present a 3D analytical model for fluidic injection
in a supersonic nozzle integrating an orifice. The fluidic vectoring
uses a sonic secondary injection in the divergent. As a result, the
flow and interaction between the main and secondary jet has built in
order to express the pressure fields from which the forces and thrust
vectoring are deduced. Under various separation criteria, the present
analytical model results are compared with the existing numerical
and experimental data from the literature.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: The goal of the modern education system is to prepare
students to be able to adapt to ever-changing life situations. They
must be able to acquire required knowledge independently; apply
such knowledge in practice to solve various problems by using
modern technologies; think critically and creatively; competently use
information; be communicative, work in a team; and develop their
own moral values, intellect and cultural awareness. As a result, the
status of education significantly increases; new requirements to its
quality have been formed. In recent years the competency-based
approach in education has become of significant interest. This
approach is a strengthening of applied and practical characteristics of
a school education and leads to the forming of the key students’
competencies which define their success in future life. In this article,
the authors’ attention focuses on a range of key competencies,
educational, informational and communicative and on the possibility
to develop such competencies via STEM education. This research
shows the change in students’ attitude towards scientific disciplines
such as mathematics, general science, technology and engineering as
a result of STEM education. Two staged analyzed questionnaires
completed by students of forms II to IV in the republic of Trinidad
and Tobago allowed the authors to categorize students between two
levels that represent students’ attitude to various disciplines. The
significance of differences between selected levels was confirmed
with the use of Pearson’s chi-squared test. In summary, the analysis
of obtained data makes it possible to conclude that STEM education
has a great potential for development of core students’ competencies
and encourage the development of positive student attitude towards
the above mentioned above scientific disciplines.
Abstract: Electrohydraulic servo system have been used in
industry in a wide number of applications. Its dynamics are highly
nonlinear and also have large extent of model uncertainties and
external disturbances. In this paper, a robust back-stepping control
(RBSC) scheme is proposed to overcome the problem of disturbances
and system uncertainties effectively and to improve the tracking
performance of EHS systems. In order to implement the proposed
control scheme, the system uncertainties in EHS systems are
considered as total leakage coefficient and effective oil volume. In
addition, in order to obtain the virtual controls for stabilizing system,
the update rule for the system uncertainty term is induced by
the Lyapunov control function (LCF). To verify the performance and
robustness of the proposed control system, computer simulation of
the proposed control system using Matlab/Simulink Software
is executed. From the computer simulation, it was found that the
RBSC system produces the desired tracking performance and has
robustness to the disturbances and system uncertainties of EHS
systems.
Abstract: Information technology plays an irreplaceable role in
introducing and improving business process orientation in a
company. It enables implementation of the theoretical concept,
measurement of results achieved and undertaking corrective
measures aimed at improvements. Information technology is a key
concept in the development and implementation of the business
process management systems as it establishes a connection to
business operations. Both in the literature and practice, insurance
companies are often seen as highly process oriented due to the nature
of their business and focus on customers. They are also considered
leaders in using information technology for business process
management. The research conducted aimed to investigate whether
the perceived leadership status of insurance companies is well
deserved, i.e. to establish the level of process orientation and explore
the practice of information technology use in insurance companies in
the region. The main instrument for primary data collection within
this research was an electronic survey questionnaire sent to the
management of insurance companies in the Republic of Croatia,
Bosnia and Herzegovina, Slovenia, Serbia and Macedonia. The
conducted research has shown that insurance companies have a
satisfactory level of process orientation, but that there is also a huge
potential for improvement, especially in the segment of information
technology and its connection to business processes.
Abstract: Financial innovations can be regarded as the cause
and the effect of the evolution of the financial system. Most of
financial innovations are created by various financial institutions for
their own purposes and needs. However, due to their diversity,
financial innovations can be also applied by various business entities
(other than financial institutions).
This paper focuses on the potential application of financial
innovations by non-financial companies. It is assumed that financial
innovations may be effectively applied in all fields of corporate
financial decisions integrating financial management with the risk
management process. Appropriate application of financial
innovations may enhance the development of the company and
increase its value by improving its financial situation and reducing
the level of risk. On the other hand, misused financial innovations
may become the source of extra risk for the company threatening its
further operation.
The main objective of the paper is to identify the major types of
financial innovations offered to non-financial companies by the
banking system in Poland. It also aims at identifying the main factors
determining the creation of financial innovations in the banking
system in Poland and indicating future directions of their
development.
This paper consists of conceptual and empirical part. Conceptual
part based on theoretical study is focused on the determinants of the
process of financial innovations and their application by the nonfinancial
companies. Theoretical study is followed by the empirical
research based on the analysis of the actual offer of the 20 biggest
banks operating in Poland with regard to financial innovations
offered to SMEs and large corporations. These innovations are
classified according to the main functions of the integrated financial
management, such as financing, investment, working capital
management and risk management.
Empirical study has proved that the biggest banks operating in the
Polish market offer to their business customers many types and
classes of financial innovations. This offer appears vast and adequate
to the needs and purposes of the Polish non-financial companies. It
was observed that financial innovations pertained to financing
decisions dominate in the banks’ offer. However, due to high
diversification of the offered financial innovations, business
customers may effectively apply them in all fields and areas of
integrated financial management. It should be underlined, that the
banks’ offer is highly dispersed, which may limit the implementation
of financial innovations in the corporate finance. It would be also
recommended for the banks operating in the Polish market to
intensify the education campaign aiming at increasing knowledge
about financial innovations among business customers.
Abstract: Cadmium (II) (Cd) is one of the major toxic elemental
pollutants, which is hazardous for humans, animals and plants. γ-
Polyglutamic acid (γ-PGA) is an extracellular biopolymer produced
by several species of Bacillus which has been reported to be an
effective biosorbent for metal ions. The effect of γ-PGA on growth of
rice grown under laboratory conditions was investigated. Rice seeds
were germinated and then grown at 30±1°C on filter paper soaked
with Cd solution and γ-PGA for 7 days. The result showed that Cd
significantly inhibited the growth of roots, shoots by reducing root,
and shoot lengths. Fresh and dry weights also decreased compared
with control; however, the addition of 500 mg·L-1 γ-PGA alleviated
rice seedlings from the adverse effects of Cd. The analysis of
physiological traits revealed that Cd caused a decrease in the total
chlorophyll and soluble protein contents and amylase activities in all
treatments. The Cd content in seedling tissues increased for the Cd
250 μM treatment (P
Abstract: In recent years, the use of the aluminum based alloys
in the industry and technology are increasing. Alloying elements in
aluminum have further been improving the strength and stiffness
properties that provide superior compared to other metals. In this
study, investigation of physical properties (microstructure,
microhardness, tensile strength, electrical conductivity and thermal
properties) in the Al-12.6wt.%Si-%2wt.Ni ternary alloy were
investigated. Al-Si-Ni alloy was prepared in vacuum atmosphere. The
samples were directionally solidified upwards with different growth
rate V (8.3−165.45 μm/s) at constant temperature gradient G (7.73
K/mm). The flake spacings (λ), microhardness (HV), ultimate tensile
strength (σ), electrical resistivity (ρ) and thermal properties (H, Cp,
Tm) of the samples were measured. Influence of the growth rate and
spacings on microhardness, ultimate tensile strength and electrical
resistivity were investigated and relationships between them were
obtained. According to results, λ values decrease with increasing V,
but HV, σ and ρ values increase with increasing V. Variations of
electrical resistivity (ρ) of solidified samples were also measured.
The enthalpy of fusion (H) and specific heat (Cp) for the alloy was
also determined by differential scanning calorimeter (DSC) from
heating trace during the transformation from liquid to solid. The
results in this work were compared with the previous similar
experimental results.
Abstract: Photovoltaic (PV) power generation systems, mainly
small scale, are rapidly being deployed in Jordan. The impact of these
systems on the grid has not been studied or analyzed. These systems
can cause many technical problems such as reverse power flows and
voltage rises in distribution feeders, and real and reactive power
transients that affect the operation of the transmission system. To
fully understand and address these problems, extensive research,
simulation, and case studies are required. To this end, this paper
studies the cloud shadow effect on the power generation of a ground
mounted PV system installed at the test field of the Renewable
Energy Center at the Applied Science University.