Abstract: Evaluation of contact pressure, surface and
subsurface contact stresses are essential to know the functional
response of surface coatings and the contact behavior mainly depends
on surface roughness, material property, thickness of layer and the
manner of loading. Contact parameter evaluation of real rough
surface contacts mostly relies on statistical single asperity contact
approaches. In this work, a three dimensional layered solid rough
surface in contact with a rigid flat is modeled and analyzed using
finite element method. The rough surface of layered solid is
generated by FFT approach. The generated rough surface is exported
to a finite element method based ANSYS package through which the
bottom up solid modeling is employed to create a deformable solid
model with a layered solid rough surface on top. The discretization
and contact analysis are carried by using the same ANSYS package.
The elastic, elastoplastic and plastic deformations are continuous in
the present finite element method unlike many other contact models.
The Young-s modulus to yield strength ratio of layer is varied in the
present work to observe the contact parameters effect while keeping
the surface roughness and substrate material properties as constant.
The contacting asperities attain elastic, elastoplastic and plastic states
with their continuity and asperity interaction phenomena is inherently
included. The resultant contact parameters show that neighboring
asperity interaction and the Young-s modulus to yield strength ratio
of layer influence the bulk deformation consequently affect the
interface strength.
Abstract: A two-dimensional numerical simulation of the contribution
of both inertial and aerodynamic forces on the blade loads of
a Vertical-Axis Wind Turbine (VAWT) is presented. After describing
the computational model and the relative validation procedure, a
complete campaign of simulations - based on full RANS unsteady
calculations - is proposed for a three-bladed rotor architecture characterized
by a NACA 0021 airfoil. For each analyzed angular velocity,
the combined effect of pressure and viscous forces acting on every
rotor blade are compared to the corresponding centrifugal forces,
due to the revolution of the turbine, thus achieving a preliminary
estimation of the correlation between overall rotor efficiency and
structural blade loads.
Abstract: A total of 33,680 nuclear power plants (NPPs) workers were monitored and recorded from 1990 to 2007. According to the record, the average individual radiation dose has been decreasing continually from it 3.20 mSv/man in 1990 to 1.12 mSv/man at the end of 2007. After the International Commission on Radiological Protection (ICRP) 60 recommendation was generalized in South Korea, no nuclear power plant workers received above 20 mSv radiation, and the numbers of relatively highly exposed workers have been decreasing continuously. The age distribution of radiation workers in nuclear power plants was composed of mainly 20-30- year-olds (83%) for 1990 ~ 1994 and 30-40-year-olds (75%) for 2003 ~ 2007. The difference in individual average dose by age was not significant. Most (77%) of NPP radiation exposures from 1990 to 2007 occurred mostly during the refueling period. With regard to exposure type, the majority of exposures were external exposures, representing 95% of the total exposures, while internal exposures represented only 5%. External effective dose was affected mainly by gamma radiation exposure, with an insignificant amount of neutron exposure. As for internal effective dose, tritium (3H) in the pressurized heavy water reactor (PHWR) was the biggest cause of exposure.
Abstract: Attachment of the circulating monocytes to the
endothelium is the earliest detectable events during formation of
atherosclerosis. The adhesion molecules, chemokines and matrix
proteases genes were identified to be expressed in atherogenesis.
Expressions of these genes may influence structural integrity of the
luminal endothelium. The aim of this study is to relate changes in the
ultrastructural morphology of the aortic luminal surface and gene
expressions of the endothelial surface, chemokine and MMP-12 in
normal and hypercholesterolemic rabbits. Luminal endothelial
surface from rabbit aortic tissue was examined by scanning electron
microscopy (SEM) using low vacuum mode to ascertain
ultrastructural changes in development of atherosclerotic lesion. Gene
expression of adhesion molecules, MCP-1 and MMP-12 were studied
by Real-time PCR. Ultrastructural observations of the aortic luminal
surface exhibited changes from normal regular smooth intact
endothelium to irregular luminal surface including marked globular
appearance and ruptures of the membrane layer. Real-time PCR
demonstrated differentially expressed of studied genes in
atherosclerotic tissues. The appearance of ultrastructural changes in
aortic tissue of hypercholesterolemic rabbits is suggested to have
relation with underlying changes of endothelial surface molecules,
chemokine and MMP-12 gene expressions.
Abstract: In-vitro mouse co-culture of E14 embryonic stem cells
(ESCs) and OP9 stromal cells can recapitulate the earliest stages of
haematopoietic development, not accessible in human embryos,
supporting both haemogenic precursors and their primitive
haematopoietic progeny. 1α, 25-Dihydroxy-vitamin D3 (VD3) has
been demonstrated to be a powerful differentiation inducer for a wide
variety of neoplastic cells, and could enhance early differentiation of
ESCs into blood cells in E14/OP9 co-culture. This study aims to
ascertain whether VD3 is key in promoting differentiation and
suppressing proliferation, by separately investigating the effects of
VD3 on the proliferation phase of the E14 cell line and on stromal
OP9 cells.The results showed that VD3 inhibited the proliferation of
the cells in a dose-dependent manner, quantitatively by decreased cell
number, and qualitatively by alkaline-phosphatase staining that
revealed significant differences between VD3-treated and untreated
cells, characterised by decreased enzyme expression (colourless
cells). Propidium-iodide cell-cycle analyses showed no significant
percentage change in VD3-treated E14 and OP9 cells within their G
and S-phases, compared to the untreated controls, despite the
increased percentage of G-phase compared to the S-phase in a dosedependent
manner. These results with E14 and OP9 cells indicate that
adequate VD3 concentration enhances cellular differentiation and
inhibits proliferation. The results also suggest that if E14 and OP9
cells were co-cultured andVD3-treated, there would be furtherenhanced
differentiation of ESCs into blood cells.
Abstract: This paper presents a method for determining the
uniaxial tensile properties such as Young-s modulus, yield strength
and the flow behaviour of a material in a virtually non-destructive
manner. To achieve this, a new dumb-bell shaped miniature
specimen has been designed. This helps in avoiding the removal of
large size material samples from the in-service component for the
evaluation of current material properties. The proposed miniature
specimen has an advantage in finite element modelling with respect
to computational time and memory space. Test fixtures have been
developed to enable the tension tests on the miniature specimen in a
testing machine. The studies have been conducted in a chromium
(H11) steel and an aluminum alloy (AR66). The output from the
miniature test viz. load-elongation diagram is obtained and the finite
element simulation of the test is carried out using a 2D plane stress
analysis. The results are compared with the experimental results. It is
observed that the results from the finite element simulation
corroborate well with the miniature test results. The approach seems
to have potential to predict the mechanical properties of the
materials, which could be used in remaining life estimation of the
various in-service structures.
Abstract: Model-based approaches have been applied successfully
to a wide range of tasks such as specification, simulation, testing, and
diagnosis. But one bottleneck often prevents the introduction of these
ideas: Manual modeling is a non-trivial, time-consuming task.
Automatically deriving models by observing and analyzing running
systems is one possible way to amend this bottleneck. To
derive a model automatically, some a-priori knowledge about the
model structure–i.e. about the system–must exist. Such a model
formalism would be used as follows: (i) By observing the network
traffic, a model of the long-term system behavior could be generated
automatically, (ii) Test vectors can be generated from the model,
(iii) While the system is running, the model could be used to diagnose
non-normal system behavior.
The main contribution of this paper is the introduction of a model
formalism called 'probabilistic regression automaton' suitable for the
tasks mentioned above.
Abstract: The presence of cold air with the convergent
topography of the Lut valley over the valley-s sloping terrain can
generate Low Level Jets (LLJ). Moreover, the valley-parallel
pressure gradients and northerly LLJ are produced as a result of the
large-scale processes. In the numerical study the regional MM5
model was run leading to achieve an appropriate dynamical analysis
of flows in the region for summer and winter. The results of this
study show the presence of summer synoptical systems cause the
formation of north-south pressure gradients in the valley which could
be led to the blowing of winds with the velocity more than 14 ms-1
and vulnerable dust and wind storms lasting more than 120 days.
Whereas the presence of cold air masses in the region in winter,
cause the average speed of LLJs decrease. In this time downslope
flows are noticeable in creating the night LLJs.
Abstract: Bioinformatics and computational biology involve
the use of techniques including applied mathematics,
informatics, statistics, computer science, artificial intelligence,
chemistry, and biochemistry to solve biological problems
usually on the molecular level. Research in computational
biology often overlaps with systems biology. Major research
efforts in the field include sequence alignment, gene finding,
genome assembly, protein structure alignment, protein structure
prediction, prediction of gene expression and proteinprotein
interactions, and the modeling of evolution. Various
global rearrangements of permutations, such as reversals and
transpositions,have recently become of interest because of their
applications in computational molecular biology. A reversal is
an operation that reverses the order of a substring of a permutation.
A transposition is an operation that swaps two adjacent
substrings of a permutation. The problem of determining the
smallest number of reversals required to transform a given
permutation into the identity permutation is called sorting by
reversals. Similar problems can be defined for transpositions
and other global rearrangements. In this work we perform a
study about some genome rearrangement primitives. We show
how a genome is modelled by a permutation, introduce some
of the existing primitives and the lower and upper bounds
on them. We then provide a comparison of the introduced
primitives.
Abstract: During recent years wind turbine technology has
undergone rapid developments. Growth in size and the optimization
of wind turbines has enabled wind energy to become increasingly
competitive with conventional energy sources. As a result today-s
wind turbines participate actively in the power production of several
countries around the world. These developments raise a number of
challenges to be dealt with now and in the future. The penetration of
wind energy in the grid raises questions about the compatibility of the
wind turbine power production with the grid. In particular, the
contribution to grid stability, power quality and behavior during fault
situations plays therefore as important a role as the reliability. In the
present work, we addressed two fault situations that have shown their
influence on the generator and the behavior of the wind over the
defects which are briefly discussed based on simulation results.
Abstract: In this study, the contact problem of a layered composite which consists of two materials with different elastic constants and heights resting on two rigid flat supports with sharp edges is considered. The effect of gravity is neglected. While friction between the layers is taken into account, it is assumed that there is no friction between the supports and the layered composite so that only compressive tractions can be transmitted across the interface. The layered composite is subjected to a uniform clamping pressure over a finite portion of its top surface. The problem is reduced to a singular integral equation in which the contact pressure is the unknown function. The singular integral equation is evaluated numerically and the results for various dimensionless quantities are presented in graphical forms.
Abstract: In this paper, all-optical signal processors that perform
both microwave mixing and bandpass filtering in a radio-over-fiber
(RoF) link are presented. The key device is a Mach-Zehnder
modulator (MZM) which performs all-optical microwave mixing. An
up-converted microwave signal is obtained and other unwanted
frequency components are suppressed at the end of the fiber span.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: In a bi-fuel diesel engine, the carburetor plays a vital
role in switching from fuel gas to petrol mode operation and viceversa.
The carburetor is the most important part of the fuel system of
a diesel engine. All diesel engines carry variable venturi mixer
carburetors. The basic operation of the carburetor mainly depends on
the restriction barrel called the venturi. When air flows through the
venturi, its speed increases and its pressure decreases. The main
challenge focuses on designing a mixing device which mixes the
supplied gas is the incoming air at an optimum ratio. In order to
surmount the identified problems, the way fuel gas and air flow in
the mixer have to be analyzed. In this case, the Computational Fluid
Dynamics or CFD approach is applied in design of the prototype
mixer. The present work is aimed at further understanding of the air
and fuel flow structure by performing CFD studies using a software
code. In this study for mixing air and gas in the condition that has
been mentioned in continuance, some mixers have been designed.
Then using of computational fluid dynamics, the optimum mixer has
been selected. The results indicated that mixer with 12 holes can
produce a homogenous mixture than those of 8-holes and 6-holes
mixer. Also the result showed that if inlet convergency was smoother
than outlet divergency, the mixture get more homogenous, the reason
of that is in increasing turbulence in outlet divergency.
Abstract: Vapour recompression system has been used to
enhance reduction in energy consumption and improvement in
energy effectiveness of distillation columns. However, the effects of
certain parameters have not been taken into consideration. One of
such parameters is the column heat loss which has either been
assumed to be a certain percent of reboiler heat transfer or negligible.
The purpose of this study was to evaluate the heat loss from an
ethanol-water vapour recompression distillation column with
pressure increase across the compressor (VRCAS) and compare the
results obtained and its effect on some parameters in similar system
(VRCCS) where the column heat loss has been assumed or neglected.
Results show that the heat loss evaluated was higher when compared
with that obtained for the column VRCCS. The results also showed
that increase in heat loss could have significant effect on the total
energy consumption, reboiler heat transfer, the number of trays and
energy effectiveness of the column.
Abstract: The excessive consumption of fossil energies (electrical energy) during summer caused by the technological development involves more and more climate warming.
In order to reduce the worst impact of gas emissions produced from classical air conditioning, heat driven solar absorption chiller is pretty promising; it consists on using solar as motive energy which is clean and environmentally friendly to provide cold.
Solar absorption machine is composed by four components using Lithium Bromide /water as a refrigerating couple. LiBr- water is the most promising in chiller applications due to high safety, high volatility ratio, high affinity, high stability and its high latent heat. The lithium bromide solution is constitute by the salt lithium bromide which absorbs water under certain conditions of pressure and temperature however if the concentration of the solution is high in the absorption chillers; which exceed 70%, the solution will crystallize.
The main aim of this article is to study the phenomena of the crystallization and to evaluate how the dependence between the electric conductivity and the concentration which should be controlled.
Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: This paper describes a UDP over IP based, server-oriented redundant host configuration protocol (RHCP) that can be used by collaborating embedded systems in an ad-hoc network to acquire a dynamic IP address. The service is provided by a single network device at a time and will be dynamically reassigned to one of the other network clients if the primary provider fails. The protocol also allows all participating clients to monitor the dynamic makeup of the network over time. So far the algorithm has been implemented and tested on an 8-bit embedded system architecture with a 10Mbit Ethernet interface.
Abstract: In this paper we present a technique to speed up
ICA based on the idea of reducing the dimensionality of the data
set preserving the quality of the results. In particular we refer to
FastICA algorithm which uses the Kurtosis as statistical property
to be maximized. By performing a particular Johnson-Lindenstrauss
like projection of the data set, we find the minimum dimensionality
reduction rate ¤ü, defined as the ratio between the size k of the reduced
space and the original one d, which guarantees a narrow confidence
interval of such estimator with high confidence level. The derived
dimensionality reduction rate depends on a system control parameter
β easily computed a priori on the basis of the observations only.
Extensive simulations have been done on different sets of real world
signals. They show that actually the dimensionality reduction is very
high, it preserves the quality of the decomposition and impressively
speeds up FastICA. On the other hand, a set of signals, on which the
estimated reduction rate is greater than 1, exhibits bad decomposition
results if reduced, thus validating the reliability of the parameter β.
We are confident that our method will lead to a better approach to
real time applications.