Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: The steady state response of bond graphs representing
passive and active suspension is presented. A bond graph with
preferred derivative causality assignment to get the steady state
is proposed. A general junction structure of this bond graph
is proposed. The proposed methodology to passive and active
suspensions is applied.
Abstract: An experimental study of Reinforced Concrete, RC, columns strengthened using a steel jacketing technique was conducted. The jacketing technique consisted of four steel vertical angles installed at the corners of the column joined by horizontal steel straps confining the column externally. The effectiveness of the technique was evaluated by testing the RC column specimens under eccentric monotonic loading until failure occurred. Strain gauges were installed to monitor the strains in the internal reinforcement as well as the external jacketing system. The effectiveness of the jacketing technique was demonstrated, and the parameters affecting the technique were studied.
Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: Aquatic and semi aquatic birds as a group are suited to
feed and breed in environments in which water forms a fundamental
part. These birds are biological indicator in aquatic environment,
because these birds belong to the top level of food chain in aquatic
ecosystems. There are 61 species in 14 families of aquatic and semi
aquatic birds in Iran. The birds of the Sattarkhan Lake belong to 16
species in 8 families which include 26.2 percent of total Aquatic and
semi aquatic bird species and 57% of Aquatic and semi aquatic bird's
family of Iran. Study was carried out monthly at Sattarkhan Lake
show the existence of Phalacrocorax carbo, Ardea cinerea, Egretta
alba, Egretta garzetta, Bubulcus ibis, Botaurus stellaris, Sterna
hirundo, Chlidonias leucopterus, Larus minutus, Larus argentatus,
Larus ridibunbus, Alcedo atthis, Ciconia ciconia, Plegadis
falcinellus, Circus aeruginosus, Corvus frugilegus
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: In this paper, a method to detect multiple ellipses is presented. The technique is efficient and robust against incomplete ellipses due to partial occlusion, noise or missing edges and outliers. It is an iterative technique that finds and removes the best ellipse until no reasonable ellipse is found. At each run, the best ellipse is extracted from randomly selected edge patches, its fitness calculated and compared to a fitness threshold. RANSAC algorithm is applied as a sampling process together with the Direct Least Square fitting of ellipses (DLS) as the fitting algorithm. In our experiment, the method performs very well and is robust against noise and spurious edges on both synthetic and real-world image data.
Abstract: This paper describes a 3D modeling system in
Augmented Reality environment, named 3DARModeler. It can be
considered a simple version of 3D Studio Max with necessary
functions for a modeling system such as creating objects, applying
texture, adding animation, estimating real light sources and casting
shadows. The 3DARModeler introduces convenient, and effective
human-computer interaction to build 3D models by combining both
the traditional input method (mouse/keyboard) and the tangible input
method (markers). It has the ability to align a new virtual object with
the existing parts of a model. The 3DARModeler targets nontechnical
users. As such, they do not need much knowledge of
computer graphics and modeling techniques. All they have to do is
select basic objects, customize their attributes, and put them together
to build a 3D model in a simple and intuitive way as if they were
doing in the real world. Using the hierarchical modeling technique,
the users are able to group several basic objects to manage them as a
unified, complex object. The system can also connect with other 3D
systems by importing and exporting VRML/3Ds Max files. A
module of speech recognition is included in the system to provide
flexible user interfaces.
Abstract: Propagation of solitons in single-mode birefringent fibers is considered under the presence of third-order dispersion (TOD). The behavior of two neighboring solitons and their interaction is investigated under the presence of third-order dispersion with different group velocity dispersion (GVD) parameters. It is found that third-order dispersion makes the resultant soliton to deviate from its ideal position and increases the interaction between adjacent soliton pulses. It is also observed that this deviation due to third-order dispersion is considerably small when the optical pulse propagates at wavelengths relatively far from the zerodispersion. Modified coupled nonlinear Schrödinger-s equations (CNLSE) representing the propagation of optical pulse in single mode fiber with TOD are solved using split-step Fourier algorithm. The results presented in this paper reveal that the third-order dispersion can substantially increase the interaction between the solitons, but large group velocity dispersion reduces the interaction between neighboring solitons.
Abstract: A novel method of learning complex fuzzy decision regions in the n-dimensional feature space is proposed. Through the fuzzy decision regions, a given pattern's class membership value of every class is determined instead of the conventional crisp class the pattern belongs to. The n-dimensional fuzzy decision region is approximated by union of hyperellipsoids. By explicitly parameterizing these hyperellipsoids, the decision regions are determined by estimating the parameters of each hyperellipsoid.Genetic Algorithm is applied to estimate the parameters of each region component. With the global optimization ability of GA, the learned decision region can be arbitrarily complex.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: This paper presents a simple approach for load
flow analysis of a radial distribution network. The proposed
approach utilizes forward and backward sweep algorithm
based on Kirchoff-s current law (KCL) and Kirchoff-s voltage
law (KVL) for evaluating the node voltages iteratively. In this
approach, computation of branch current depends only on the
current injected at the neighbouring node and the current in
the adjacent branch. This approach starts from the end nodes
of sub lateral line, lateral line and main line and moves
towards the root node during branch current computation. The
node voltage evaluation begins from the root node and moves
towards the nodes located at the far end of the main, lateral
and sub lateral lines. The proposed approach has been tested
using four radial distribution systems of different size and
configuration and found to be computationally efficient.
Abstract: The birdhouses and dovecotes, which are the indicator
of naturalness and human-animal relationship, are one of the
traditional cultural values of Turkey. With their structures compatible
with nature and respectful to humans the bird houses and dovecotes,
which have an important position in local urbanization models as a
representative of the civil architecture with their unique form and
function are important subjects that should be evaluated in a wide
frame comprising from architecture to urbanism, from ecologic
agriculture to globalization. The traditional bird houses and
dovecotes are disregarded due to the insensitivity affecting the city
life and the change in the public sense of art. In this study, the
characteristic properties of traditional dovecotes and birdhouses,
started in 13th century and ended in 19th century in Anatolia, are
tried to be defined for the sustainability of the tradition and for giving
a new direction to the designers.
Abstract: Application of neural networks in execution of
programmed pulse width modulation (PPWM) of a voltage source
inverter (VSI) is studied in this paper. Using the proposed method it is
possible to cancel out the desired harmonics in output of VSI in
addition to control the magnitude of fundamental harmonic,
contineously. By checking the non-trained values and a performance
index, the most appropriate neural network is proposed. It is shown
that neural networks may solve the custom difficulties of practical
utilization of PPWM such as large size of memory, complex digital
circuits and controlling the magnitude of output voltage in a discrete
manner.
Abstract: The number of users supported in a DS-CDMA
cellular system is typically less than spreading factor (N), and the
system is said to be underloaded. Overloading is a technique to
accommodate more number of users than the spreading factor N. In
O/O overloading scheme, the first set is assigned to the N
synchronous users and the second set is assigned to the additional
synchronous users. An iterative multistage soft decision interference
cancellation (SDIC) receiver is used to remove high level of
interference between the two sets. Performance is evaluated in terms
of the maximum number acceptable users so that the system
performance is degraded slightly compared to the single user
performance at a specified BER. In this paper, the capacity of CDMA
based O/O overloading scheme is evaluated with SDIC receiver. It is
observed that O/O scheme using orthogonal Gold codes provides
25% channel overloading (N=64) for synchronous DS-CDMA
system on an AWGN channel in the uplink at a BER of 1e-5.For a
Rayleigh faded channel, the critical capacity is 40% at a BER of 5e-5
assuming synchronous users. But in practical systems, perfect chip
timing is very difficult to maintain in the uplink.. We have shown that
the overloading performance reduces to 11% for a timing
synchronization error of 0.02Tc for a BER of 1e-5.
Abstract: Frequently a group of people jointly decide and authorize
a specific person as a representative in some business/poitical
occasions, e.g., the board of a company authorizes the chief executive
officer to close a multi-billion acquisition deal. In this paper, an
integrated proxy multi-signature scheme that allows anonymously
vetoable delegation is proposed. This protocol integrates mechanisms
of private veto, distributed proxy key generation, secure transmission
of proxy key, and existentially unforgeable proxy multi-signature
scheme. First, a provably secure Guillou-Quisquater proxy signature
scheme is presented, then the “zero-sharing" protocol is extended
over a composite modulus multiplicative group, and finally the above
two are combined to realize the GQ proxy multi-signature with
anonymously vetoable delegation. As a proxy signature scheme, this
protocol protects both the original signers and the proxy signer.
The modular design allows simplified implementation with less
communication overheads and better computation performance than
a general secure multi-party protocol.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: This paper describes the application of a model
predictive controller to the problem of batch reactor temperature
control. Although a great deal of work has been done to improve
reactor throughput using batch sequence control, the control of the
actual reactor temperature remains a difficult problem for many
operators of these processes. Temperature control is important as
many chemical reactions are sensitive to temperature for formation of
desired products. This controller consist of two part (1) a nonlinear
control method GLC (Global Linearizing Control) to create a linear
model of system and (2) a Model predictive controller used to obtain
optimal input control sequence. The temperature of reactor is tuned
to track a predetermined temperature trajectory that applied to the
batch reactor. To do so two input signals, electrical powers and the
flow of coolant in the coil are used. Simulation results show that the
proposed controller has a remarkable performance for tracking
reference trajectory while at the same time it is robust against noise
imposed to system output.
Abstract: Polynomial maps offer analytical properties used to obtain better performances in the scope of chaos synchronization under noisy channels. This paper presents a new method to simplify equations of the Exact Polynomial Kalman Filter (ExPKF) given in [1]. This faster algorithm is compared to other estimators showing that performances of all considered observers vanish rapidly with the channel noise making application of chaos synchronization intractable. Simulation of ExPKF shows that saturation drawn on the emitter to keep it stable impacts badly performances for low channel noise. Then we propose a particle filter that outperforms all other Kalman structured observers in the case of noisy channels.
Abstract: The present work is a numerical simulation of
nanofluids flow in a double pipe heat exchanger provided with
porous baffles. The hot nanofluid flows in the inner cylinder, whereas
the cold nanofluid circulates in the annular gap. The Darcy-
Brinkman-Forchheimer model is adopted to describe the flow in the
porous regions, and the governing equations with the appropriate
boundary conditions are solved by the finite volume method. The
results reveal that the addition of metallic nanoparticles enhances the
rate of heat transfer in comparison to conventional fluids but this
augmentation is accompanied by an increase in pressure drop. The
highest heat exchanger performances are obtained when
nanoparticles are added only to the cold fluid.