Abstract: In this paper a sliding-mode torque and flux control is
designed for encoderless synchronous reluctance motor drive. The
sliding-mode plus PI controllers are designed in the stator-flux field
oriented reference frame which is able to track the mentioned
reference signals with a minimum pulsations in the state condition. In
addition, with these controllers a fast dynamic response is also
achieved for the drive system. The proposed control scheme is robust
subject to parameters variation except to stator resistance. To solve
this problem a simple estimator is used for on-line detecting of this
parameter. Moreover, the rotor position and speed are estimated by
on-line obtaining of the stator-flux-space vector. The effectiveness
and capability of the proposed control approach is verified by both
the simulation and experimental results.
Abstract: The impeller and the casing are the key components of
a centrifugal pump. Although there have been many studies on the
impeller and the volute casing of centrifugal pump, further study of the
volute casing to improve the performance of centrifugal pumps is
needed. In this paper, the effect of cross-sectional area on the
performance of volute casing was investigated using a commercial
CFD code. The performance characteristics, not only at the off-design
point but also for a full type model are required these days. So we
conducted numerical analysis for all operating points by using
complete geometry through transient analysis. Transient analysis on
the complete geometry of a real product has the advantage of
simulating realistic flow. The results of this study show the variation of
a performance curve by modifying the above-mentioned design
parameter.
Abstract: One of the important applications of gas turbines is
their utilization for heat recovery steam generator in combine-cycle technology. Exhaust flow and energy are two key parameters for
determining heat recovery steam generator performance which are mainly determined by the main gas turbine components performance
data. For this reason a method was developed for determining the
exhaust energy in the new edition of ASME PTC22. The result of this investigation shows that the method of standard has considerable
error. Therefore in this paper a new method is presented for modifying of the performance calculation. The modified method is
based on exhaust gas constituent analysis and combustion calculations. The case study presented here by two kind of General
Electric gas turbine design data for validation of methodologies. The
result shows that the modified method is more precise than the ASME PTC22 method. The exhaust flow calculation deviation from
design data is 1.5-2 % by ASME PTC22 method so that the deviation regarding with modified method is 0.3-0.5%. Based on precision of
analyzer instruments, the method can be suitable alternative for gas
turbine standard performance test. In advance two methods are
proposed based on known and unknown fuel in modified method procedure. The result of this paper shows that the difference between
the two methods is below than %0.02. In according to reasonable esult of the second procedure (unknown fuel composition), the
method can be applied to performance evaluation of gas turbine, so that the measuring cost and data gathering should be reduced.
Abstract: This study fabricates p-type Ni1−xO:Li/n-Si heterojunction solar cells (P+/n HJSCs) by using radio frequency (RF) magnetron sputtering and investigates the effect of substrate temperature on photovoltaic cell properties. Grazing incidence x-ray diffraction, four point probe, and ultraviolet-visible-near infrared discover the optoelectrical properties of p-Ni1-xO thin films. The results show that p-Ni1-xO thin films deposited at 300 oC has the highest grain size (22.4 nm), average visible transmittance (~42%), and electrical resistivity (2.7 Ωcm). However, the conversion efficiency of cell is shown only 2.33% which is lower than the cell (3.39%) fabricated at room temperature. This result can be mainly attributed to interfacial layer thickness (SiOx) reduces from 2.35 nm to 1.70 nm, as verified by high-resolution transmission electron microscopy.
Abstract: This paper deals with the optimal design of two-channel recursive parallelogram quadrature mirror filter (PQMF) banks. The analysis and synthesis filters of the PQMF bank are composed of two-dimensional (2-D) recursive digital all-pass filters (DAFs) with nonsymmetric half-plane (NSHP) support region. The design problem can be facilitated by using the 2-D doubly complementary half-band (DC-HB) property possessed by the analysis and synthesis filters. For finding the coefficients of the 2-D recursive NSHP DAFs, we appropriately formulate the design problem to result in an optimization problem that can be solved by using a weighted least-squares (WLS) algorithm in the minimax (L∞) optimal sense. The designed 2-D recursive PQMF bank achieves perfect magnitude response and possesses satisfactory phase response without requiring extra phase equalizer. Simulation results are also provided for illustration and comparison.
Abstract: This paper proposes method of diagnosing ball screw
preload loss through the Hilbert-Huang Transform （HHT） and
Multiscale entropy （MSE） process. The proposed method can
diagnose ball screw preload loss through vibration signals when the
machine tool is in operation. Maximum dynamic preload of 2 %, 4 %,
and 6 % ball screws were predesigned, manufactured, and tested
experimentally. Signal patterns are discussed and revealed using
Empirical Mode Decomposition（EMD）with the Hilbert Spectrum.
Different preload features are extracted and discriminated using HHT.
The irregularity development of a ball screw with preload loss is
determined and abstracted using MSE based on complexity
perception. Experiment results show that the proposed method can
predict the status of ball screw preload loss. Smart sensing for the
health of the ball screw is also possible based on a comparative
evaluation of MSE by the signal processing and pattern matching of
EMD/HHT. This diagnosis method realizes the purposes of prognostic
effectiveness on knowing the preload loss and utilizing convenience.
Abstract: Starting from the basic pillars of the supportability
analysis this paper queries its characteristics in LCI (Life Cycle
Integration) environment. The research methodology contents a
review of modern logistics engineering literature with the objective to
collect and synthesize the knowledge relating to standards of
supportability design in e-logistics environment. The results show
that LCI framework has properties which are in fully compatibility
with the requirement of simultaneous logistics support and productservice
bundle design. The proposed approach is a contribution to the
more comprehensive and efficient supportability design process.
Also, contributions are reflected through a greater consistency of
collected data, automated creation of reports suitable for different
analysis, as well as the possibility of their customization according
with customer needs. In addition to this, convenience of this approach
is its practical use in real time. In a broader sense, LCI allows
integration of enterprises on a worldwide basis facilitating electronic
business.
Abstract: With the prevalence of computer and development of information technology, Geographic Information Systems (GIS) have long used for a variety of applications in electrical engineering. GIS are designed to support the analysis, management, manipulation and mapping of spatial data. This paper presents several usages of GIS in power utilities such as automated route selection for the construction of new power lines which uses a dynamic programming model for route optimization, load forecasting and optimizing planning of substation-s location and capacity with comprehensive algorithm which involves an accurate small-area electric load forecasting procedure and simulates the different cost functions of substations.
Abstract: This paper presents the automated methods employed
for extracting craniofacial landmarks in white light images as part of
a registration framework designed to support three neurosurgical
procedures. The intraoperative space is characterised by white light
stereo imaging while the preoperative plan is performed on CT scans.
The registration aims at aligning these two modalities to provide a
calibrated environment to enable image-guided solutions. The
neurosurgical procedures can then be carried out by mapping the
entry and target points from CT space onto the patient-s space. The
registration basis adopted consists of natural landmarks (eye corner
and ear tragus). A 5mm accuracy is deemed sufficient for these three
procedures and the validity of the selected registration basis in
achieving this accuracy has been assessed by simulation studies. The
registration protocol is briefly described, followed by a presentation
of the automated techniques developed for the extraction of the
craniofacial features and results obtained from tests on the AR and
FERET databases. Since the three targeted neurosurgical procedures
are routinely used for head injury management, the effect of
bruised/swollen faces on the automated algorithms is assessed. A
user-interactive method is proposed to deal with such unpredictable
circumstances.
Abstract: With the proliferation of Weblogs (blogs) use in
educational contexts, gaining a better understanding of why
students are willing to utilize blog systems has become an
important topic for practitioners and academics. While perceived
enjoyment has been found to have a significant influence on
behavioral intentions to use blogs or hedonic systems, few studies
have investigated the antecedents of perceived enjoyment in the
acceptance of blogging. The main purpose of the present study is to
explore the individual difference antecedents of perceived
enjoyment and examine how they influence behavioral intention to
blog through the mediation of perceived enjoyment. Based on the
previous literature, the Big Five personality traits (i.e.,
extraversion, agreeableness, conscientiousness, neuroticism, and
openness to experience), as well as computer self-efficacy and
personal innovation in information technology (PIIT), are
hypothesized as potential antecedents of perceived enjoyment in
the acceptance of blogging. Data collected from 358 respondents in
Taiwan are tested against the research model using the structural
equation modeling approach. The results indicate that extraversion,
agreeableness, conscientiousness, and PIIT have a significant
influence on perceived enjoyment, which in turn significantly
influences the behavioral intention to blog. These findings lead to
several important implications for future research.
Abstract: In this paper, the absorption and fluorescence
emission spectra of Yb:Y3Al5O12 (YAG)(25 at%) crystal as a disk
laser medium are measured at high temperature (300-450K). The
absorption and emission cross sections of Yb:YAG crystal are
determined using Reciprocity method. Temperature dependence of
941nm absorption cross section and 1031nm emission cross section
is extracted in the range of 300-450K. According to our experimental
results, an exponential temperature dependence between 300K and
450K is acquired for the 1031nm peak emission cross section and
also for 941nm peak absorption cross section of Yb:YAG crystal.
These results could be used for simulation and design of high power
highly doped Yb:YAG thin disk lasers.
Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: This paper proposes a neural network weights and
topology optimization using genetic evolution and the
backpropagation training algorithm. The proposed crossover and
mutation operators aims to adapt the networks architectures and
weights during the evolution process. Through a specific inheritance
procedure, the weights are transmitted from the parents to their
offsprings, which allows re-exploitation of the already trained
networks and hence the acceleration of the global convergence of the
algorithm. In the preprocessing phase, a new feature extraction
method is proposed based on Legendre moments with the Maximum
entropy principle MEP as a selection criterion. This allows a global
search space reduction in the design of the networks. The proposed
method has been applied and tested on the well known MNIST
database of handwritten digits.
Abstract: Based on the combined shape feature and texture
feature, a fast object detection method with rotation invariant features
is proposed in this paper. A quick template matching scheme based
online learning designed for online applications is also introduced in
this paper. The experimental results have shown that the proposed
approach has the features of lower computation complexity and
higher detection rate, while keeping almost the same performance
compared to the HOG-based method, and can be more suitable for
run time applications.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: One of the efficient factors in comprehensive
development of an area is to provide water sources and on the other
hand the appropriate management of them. Population growth and
nourishment security for such a population necessitate the
achievement of constant development besides the reforming of
traditional management in order to increase the profit of sources; In
this case, the constant exploitation of sources for the next generations
will be considered in this program. The achievement of this
development without the consideration and possibility of water
development will be too difficult. Zayanderood basin with 41500
areas in square kilometers contains 7 sub-basins and 20 units of
hydrologic. In this basin area, from the entire environment
descending, just a small part will enter into the river currents and the
rest will be out of efficient usage by various ways. The most
important surface current of this basin is Zayanderood River with
403 kilometers length which is originated from east slopes of Zagros
mount and after draining of this basin area it will enter into
Gaavkhooni pond. The existence of various sources and
consumptions of water in Zayanderood basin, water transfer of the
other basin areas into this basin, of course the contradiction between
the upper and lower beneficiaries, the existence of worthwhile
natural ecosystems such as Gaavkhooni swamp in this basin area and
finally, the drought condition and lack of water in this area all
necessitate the existence of comprehensive management of water
sources in this central basin area of Iran as this method is a kind of
management which considers the development and the management
of water sources as an equilibrant way to increase the economical
and social benefits. In this study, it is tried to survey the network of
surface water sources of basin in upper and lower sections; at the
most, according to the difficulties and deficiencies of an efficient
management of water sources in this basin area, besides the
difficulties of water draining and the destructive phenomenon of
flood-water, the appropriate guidelines according to the region
conditions are presented in order to prevent the deviation of water in
upper sections and development of regions in lower sections of
Zayanderood dam.
Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.