Abstract: This paper presents the experimental results of
leakage current waveforms which appears on porcelain insulator
surface due to existence of artificial pollutants. The tests have been
done using the chemical compounds of NaCl, Na2SiO3, H2SO4, CaO,
Na2SO4, KCl, Al2SO4, MgSO4, FeCl3, and TiO2. The insulator
surface was coated with those compounds and dried. Then, it was
tested in the chamber where the high voltage was applied. Using
correspondence analysis, the result indicated that the fundamental
harmonic of leakage current was very close to the applied voltage
and third harmonic leakage current was close to the yielded leakage
current amplitude. The first harmonic power was correlated to first
harmonic amplitude of leakage current, and third harmonic power
was close to third harmonic one. The chemical compounds of H2SO4
and Na2SiO3 affected to the power factor of around 70%. Both are the
most conductive, due to the power factor drastically increase among
the chemical compounds.
Abstract: For relatively small particles of aluminum (5%) is observed to
corrode before passivation occurs at moderate temperatures (>50oC)
in de-ionized water within one hour. Physical contact with alumina
powder results in a significant increase in both the rate of corrosion
and the extent of corrosion before passivation. Whereas the resulting
release of hydrogen gas could be of commercial interest for portable
hydrogen supply systems, the fundamental aspects of Al corrosion
acceleration in presence of dispersed alumina particles are equally
important. This paper investigates the effects of various amounts of
alumina on the corrosion rate of aluminum powders in water and the
effect of multiple additions of aluminum into a single reactor.
Abstract: Employee-s task performance has been recognized as a
core contributor to overall organizational effectiveness. Hence,
verifying the determinants of task performance is one of the most
important research issues. This study tests the influence of perceived
organizational support, abusive supervision, and exchange ideology
on employee-s task performance. We examined our hypotheses by
collecting self-reported data from 413 Korean employees in different
organizations. Our all hypotheses gained support from the results.
Implications for research and directions for future research are
discussed.
Abstract: Sustainable development is highly dependent on the
implementation of environmental education programs, which has as
its ultimate goal to produce environmentally literate citizens that
undertake environmentally friendly actions. Efforts on environmental
education along past years are now perceived on the increase of
citizens awareness on European countries and, particularly, in
Portugal. However, we still have a lack of information on the
prevalence of specific behaviors that contributes to sustainability,
influenced by a new attitude toward the environment. The
determination of pro-environmental behaviors prevalence in higher
education students is an important approach to understand to which
extend the next leading generation is, in practice, committed with the
goals of sustainable development. Therefore, present study evaluates
the prevalence of a specific set of behaviors (water savings, energy
savings, environmental criteria on shopping, and mobility) on the
University of Madeira students and discusses their commitment with
sustainable development.
Abstract: Face detection and recognition has many applications
in a variety of fields such as security system, videoconferencing and
identification. Face classification is currently implemented in
software. A hardware implementation allows real-time processing,
but has higher cost and time to-market.
The objective of this work is to implement a classifier based on
neural networks MLP (Multi-layer Perceptron) for face detection.
The MLP is used to classify face and non-face patterns. The systm is
described using C language on a P4 (2.4 Ghz) to extract weight
values. Then a Hardware implementation is achieved using VHDL
based Methodology. We target Xilinx FPGA as the implementation
support.
Abstract: Biological, psychological and social experiences and
perceptions of healthcare services in patients medically diagnosed of
coronary heart disease were investigated using a sample of 10
participants whose responses to the in-depth interview questions
were analyzed based on inter-and-intra-case analyses. The results
obtained revealed that advancing age, single status, divorce and/or
death of spouse and the issue of single parenting negatively impacted
patients- biopsychosocial experiences. The patients- experiences of
physical signs and symptoms, anxiety and depression, past serious
medical conditions, use of self-prescribed medications, family
history of poor mental/medical or physical health, nutritional
problems and insufficient physical activities heightened their risk of
coronary attack. Collectivist culture served as a big source of relieve
to the patients. Patients- temperament, experience of different
chronic life stresses/challenges, mood alteration, regular drinking,
smoking/gambling, and family/social impairments compounded their
health situation. Patients were satisfied with the biomedical services
rendered by the healthcare personnel, whereas their psychological
and social needs were not attended to. Effective procedural treatment
model, a holistic and multidimensional approach to the treatment of
heart disease patients was proposed.
Abstract: The objective of this study was to develop and compare alternative prediction equations of lean meat proportion (LMP) of lamb carcasses. Forty (40) male lambs, 22 of Churra Galega Bragançana Portuguese local breed and 18 of Suffolk breed were used. Lambs were slaughtered, and carcasses weighed approximately 30 min later in order to obtain hot carcass weight (HCW). After cooling at 4º C for 24-h a set of seventeen carcass measurements was recorded. The left side of carcasses was dissected into muscle, subcutaneous fat, inter-muscular fat, bone, and remainder (major blood vessels, ligaments, tendons, and thick connective tissue sheets associated with muscles), and the LMP was evaluated as the dissected muscle percentage. Prediction equations of LMP were developed, and fitting quality was evaluated through the coefficient of determination of estimation (R2 e) and standard error of estimate (SEE). Models validation was performed by k-fold crossvalidation and the coefficient of determination of prediction (R2 p) and standard error of prediction (SEP) were computed. The BT2 measurement was the best single predictor and accounted for 37.8% of the LMP variation with a SEP of 2.30%. The prediction of LMP of lamb carcasses can be based simple models, using as predictors the HCW and one fat thickness measurement.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a small
straight-bladed Darrieus-type vertical axis wind turbine depending on
blade geometrical section. It consists of an analytical code coupled to
a solid modeling software, capable of generating the desired blade
geometry based on the desired blade design geometric parameters.
Such module is then linked to a finite volume commercial CFD code
for the calculation of rotor performance by integration of the
aerodynamic forces along the perimeter of each blade for a full period
of revolution.After describing and validating the computational
model with experimental data, the results of numerical simulations
are proposed on the bases of two candidate airfoil sections, that is a
classical symmetrical NACA 0021 blade profile and the recently
developed DU 06-W-200 non-symmetric and laminar blade
profile.Through a full CFD campaign of analysis, the effects of blade
geometrical section on angle of attack are first investigated and then
the overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of airfoil geometry on overall rotor performance.
Abstract: This paper aims to develop a model that assists the
international retailer in selecting the country that maximizes the
degree of fit between the retailer-s goals and the country
characteristics in his initial internationalization move. A two-stage
multi criteria decision model is designed integrating the Analytic
Hierarchy Process (AHP) and Goal Programming. Ethical, cultural,
geographic and economic proximity are identified as the relevant
constructs of the internationalization decision. The constructs are
further structured into sub-factors within analytic hierarchy. The
model helps the retailer to integrate, rank and weigh a number of
hard and soft factors and prioritize the countries accordingly. The
model has been implemented on a Turkish luxury goods retailer who
was planning to internationalize. Actual entry of the specific retailer
in the selected country is a support for the model. Implementation on
a single retailer limits the generalizability of the results; however, the
emphasis of the paper is on construct identification and model
development. The paper enriches the existing literature by proposing
a hybrid multi objective decision model which introduces new soft
dimensions i.e. perceived distance, ethical proximity, humane
orientation to the decision process and facilitates effective decision
making.
Abstract: This paper presents a novel sinusoidal modulation
scheme that features least correlated noise and high linearity. The
modulation circuit, which is composed of a quantizer, a resonator, and
a comparator, is capable of eliminating correlated modulation noise
while doing modulation. The proposed modulation scheme combined
with the linear quadratic optimal control is applied to a single-phase
voltage source inverter and validated with the experiment results. The
experiments show that the inverter supplies stable 60Hz 110V AC
power with a total harmonic distortion of less than 1%, under the DC
input variation from 190 V to 300 V and the output power variation
from 0 to 600 W.
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: Every 2-3 years the influenza B virus serves
epidemics. Neuraminidase (NA) is an important target for influenza
drug design. Although, oseltamivir, an oral neuraminidase drug, has
been shown good inhibitory efficiency against wild-type of influenza
B virus, the lower susceptibility to the R152K mutation has been
reported. Better understanding of oseltamivir efficiency and
resistance toward the influenza B NA wild-type and R152K mutant,
respectively, could be useful for rational drug design. Here, two
complex systems of wild-type and R152K NAs with oseltamivir
bound were studied using molecular dynamics (MD) simulations.
Based on 5-ns MD simulation, the loss of notable hydrogen bond and
decrease in per-residue decomposition energy from the mutated
residue K152 contributed to drug compared to those of R152 in wildtype
were found to be a primary source of high-level of oseltamivir
resistance due to the R152K mutation.
Abstract: In this paper we present a novel technique for data
hiding in binary document images. We use the concept of entropy in
order to identify document specific least distortive areas throughout
the binary document image. The document image is treated as any
other image and the proposed method utilizes the standard document
characteristics for the embedding process. Proposed method
minimizes perceptual distortion due to embedding and allows
watermark extraction without the requirement of any side information
at the decoder end.
Abstract: As a learning theory tries to borrow from science a framework to found its method, it shows paradoxes and paralysing contraddictions. This results, on one hand, from adopting a learning/teaching model as it were a mere “transfer of data" (mechanical learning approach), and on the other hand from borrowing the complexity theory (an indeterministic and non-linear model), that risks to vanish every educational effort. This work is aimed at describing existing criticism, unveiling the antinomic nature of such paradoxes, focussing on a view where neither the mechanical learning perspective nor the chaotic and nonlinear model can threaten and jeopardize the educational work. Author intends to go back over the steps that led to these paradoxes and to unveil their antinomic nature. Actually this could serve the purpose to explain some current misunderstandings about the real usefulness of Ict within the youth-s learning process and growth.
Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: This research aimed to study the market feasibility for
new brand coffee house, the case study of Thailand.. This study is a
mixed methods research combining quantitative research and the
qualitative research. Primary data 350 sets of questionnaires were
distributed, and the high quality completed questionnaires of 320 sets
returned. Research samples are identified as customers’ of Hi-end
department stores in Thailand. The sources of secondary data were
critical selected from highly reliable sources, both from public and
private sectors. The results were used to classify the customer group
into two main groups, the younger than 25 and the older than 25years
old. Results of the younger group, are give priority to the dimension
of coffee house and its services dimension more than others, then
branding dimension and the product dimension respectively. On the
other hand, the older group give the difference result as they rate the
important of the branding, coffee house and its services, then the
product respectively. Coffee consuming is not just the trend but it
has become part of people lifestyle. And the new cultures also created
by the wise businessman. Coffee was long produced and consumed in
Thailand. But it is surprisingly the hi-end brand coffee houses in Thai
market are mostly imported brands. The café business possibility for
Thai brand coffee house in Thai market were discussed in the paper.
Abstract: The purposes of this study are to study political
information exposure, politicians- perceptions, political attitudes and
political participations among people in Bangkok Metropolitan Area.
The sample consisted of 420 which were selected by using accidental sampling method. Questionnaires were administered to all of the
respondents to obtain the data for this research. T-test, one-way ANOVA and Pearson-s correlation coefficient were used to analyze the data. The findings are as follows: The difference in gender,
education, income and occupation has significantly effect upon political information exposures. The difference in age, income has
significantly effect upon politicians- perceptions. The difference in income has significantly effect upon political attitudes. The
difference in gender, income and occupation has significantly effect
upon political participations. There were a significantly relations between political information exposures, political attitudes, political
participations and between politicians- perceptions, political attitudes and political participations.
Abstract: The purpose of this study was to assess the value of Second Life among post-secondary instructors with experience using Second Life as an educational tool. Using Everett Rogers-s diffusion of innovations theory, survey respondents (N = 162), were divided into three adopter categories: innovators, early adopters and the early majority. Respondents were from 15 countries and 25 academic disciplines, indicating the considerable potential this innovation has to be adopted across many different borders and in many areas of academe. Nearly 94% of respondents said they plan to use Second Life again as an educational tool. However, no significant differences were found in instructors- levels of satisfaction with Second Life as an educational tool or their perceived effect on student learning across adopter categories. On the other hand, instructors who conducted class fully in Second Life were significantly more satisfied than those who used Second Life as only a small supplement to a real-world class. Overall, personal interest factors, rather than interpersonal communication factors, most influenced respondents- decision to adopt Second Life as an educational tool. In light of these findings, theoretical implications are discussed and practical suggestions are provided.