Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: The material selection in the design of the sandwich
structures is very crucial aspect because of the positive or negative
influences of the base materials to the mechanical properties of the
entire panel. In the literature, it was presented that the selection of the
skin and core materials plays very important role on the behavior of
the sandwich. Beside this, the use of the correct adhesive can make
the whole structure to show better mechanical results and behavior.
In the present work, the static three-point bending tests were
performed on the sandwiches having an aluminum alloy foam core,
the skins made of three different types of fabrics and two different
commercial adhesives (flexible polyurethane and toughened epoxy
based) at different values of support span distances by aiming the
analyses of their flexural performance in terms of absorbed energy,
peak force values and collapse mechanisms. The main results of the
flexural loading are: force-displacement curves obtained after the
bending tests, peak force and absorbed energy values, collapse
mechanisms and adhesion quality. The experimental results presented
that the sandwiches with epoxy based toughened adhesive and the
skins made of S-Glass Woven fabrics indicated the best adhesion
quality and mechanical properties. The sandwiches with toughened
adhesive exhibited higher peak force and energy absorption values
compared to the sandwiches with flexible adhesive. The use of these
sandwich structures can lead to a weight reduction of the transport
vehicles, providing an adequate structural strength under operating
conditions.
Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: R.C.C. buildings with dual structural system
consisting of shear walls (or braces) and moment resisting frames
have been widely used to resist lateral forces during earthquakes. The
dual systems are designed to resist the total design lateral force in
proportion to their lateral stiffness. The response of combination of
braces and shear walls has not yet been studied. The combination
may prove to be more effective to resist lateral forces during
earthquakes. This concept has been applied to regular R.C.C.
buildings provided with shear walls, braces and their combinations.
Abstract: Considering palm oil as non-drying oil owing to its
low iodine value, an attempt was taken to increase the unsaturation in
the fatty acid chains of palm oil for the preparation of alkyds. To
increase the unsaturation in the palm oil, sulphuric acid (SA) and
para-toluene sulphonic acid (PTSA) was used prior to alcoholysis for
the dehydration process. The iodine number of the oil samples was
checked for the unsaturation measurement by Wijs method. Alkyd
resin was prepared using the dehydrated palm oil by following
alcoholysis and esterification reaction. To improve the film properties
0.5wt.% multi-wall carbon nano tubes (MWCNTs) were used to
manufacture polymeric film. The properties of the resins were
characterized by various physico-chemical properties such as density,
viscosity, iodine value, saponification value, etc. Structural
elucidation was confirmed by Fourier transform of infrared
spectroscopy and proton nuclear magnetic resonance; surfaces of the
films were examined by field-emission scanning electron microscope.
In addition, pencil hardness and chemical resistivity was also
measured by using standard methods. The effect of enhancement of
the unsaturation in the fatty acid chain found significant and
motivational. The resin prepared with dehydrated palm oil showed
improved properties regarding hardness and chemical resistivity
testing. The incorporation of MWCNTs enhanced the thermal
stability and hardness of the films as well.
Abstract: Within the framework of this research, the regulatory
documents, which are in force in relation to this industry, were
analyzed. The main attention is turned to their modernization and
necessity of their compliance with European standards.
It is a current issue to direct the efforts of state policy on support
of business by implementing infrastructural projects, as well as by
development of human resources, which may be possible by
supporting the relevant higher and vocational studying-educational
programs.
Abstract: There is a trend in development discourse to
understand and explain the level of corruption in Nigeria, its anticorruption
crusade and why it is failing, as well as its level of
compliance with International standards of United Nations
Convention against Corruption (UNCAC) & African Union
Convention on Converting and Preventing Corruption) to which
Nigeria is a signatory. This paper discusses the legal and
Constitutional provisions relating to corrupt practices and safeguards
in Nigeria, as well as the obstacles to the implementation of these
Conventions.
The paper highlights the challenges posed to the Anti-Corruption
crusade by analysing the loopholes that exist both in administrative
structure and in scope of the relevant laws. The paper argues that
Nigerian Constitution did not make adequate provisions for the
implementation of the conventions, hence a proposal which will
ensure adequate provision for implementing the conventions to better
the lives of Nigerians. The paper concludes that there is the need to
build institutional parameters, adequate constitutional and structural
safeguards, as well as to synergise strategies, collaborations and
alliances to facilitate the timely domestication and implementation of
the conventions.
Abstract: This article discusses ways to implement a
differentiated approach to developing academic motivation for
mathematical studies which relies on defining the primary structural
characteristics of motivation. The following characteristics are
considered: features of realization of cognitive activity, meaningmaking
characteristics, level of generalization and consistency of
knowledge acquired by personal experience. The assessment of the
present level of individual student understanding of each component
of academic motivation is the basis for defining the relevant
educational strategy for its further development.
Abstract: To determine the potential of a low cost Irish
engineered timber product to replace high cost solid timber for use in
bending active structures such as gridshells a single Irish engineered
timber product in the form of orientated strand board (OSB) was
selected. A comparative study of OSB and solid timber was carried
out to determine the optimum properties that make a material suitable
for use in gridshells. Three parameters were identified to be relevant
in the selection of a material for gridshells. These three parameters
are the strength to stiffness ratio, the flexural stiffness of
commercially available sections, and the variability of material and
section properties. It is shown that when comparing OSB against
solid timber, OSB is a more suitable material for use in gridshells that
are at the smaller end of the scale and that have tight radii of
curvature. Typically, for solid timber materials, stiffness is used as an
indicator for strength and engineered timber is no different. Thus, low
flexural stiffness would mean low flexural strength. However, when
it comes to bending active gridshells, OSB offers a significant
advantage. By the addition of multiple layers, an increased section
size is created, thus endowing the structure with higher stiffness and
higher strength from initial low stiffness and low strength materials
while still maintaining tight radii of curvature. This allows OSB to
compete with solid timber on large scale gridshells. Additionally, a
preliminary sustainability study using a set of sustainability indicators
was carried out to determine the relative sustainability of building a
large-scale gridshell in Ireland with a primary focus on economic
viability but a mention is also given to social and environmental
aspects. For this, the Savill garden gridshell in the UK was used as
the functional unit with the sustainability of the structural roof
skeleton constructed from UK larch solid timber being compared
with the same structure using Irish OSB. Albeit that the advantages of
using commercially available OSB in a bending active gridshell are
marginal and limited to specific gridshell applications, further study
into an optimised engineered timber product is merited.
Abstract: The dissimilar joint between aluminum/titanium
alloys (Al 6082 and Ti G2) were successfully achieved by CO2 laser
welding with a single pass and without filler material using the
overlap joint design. Laser welding parameters ranges combinations
were experimentally determined using Taguchi approach with the
objective of producing welded joint with acceptable welding profile
and high quality of mechanical properties. In this study a joining of
dissimilar Al 6082 / Ti G2 was resulted in three distinct regions
fusion area in the weldment. These regions are studied in terms of its
microstructural characteristics and microhardness which are directly
affecting the welding quality.
The weld metal was mainly composed of martensite alpha prime.
In two different metals in the two different sides of joint HAZ, grain
growth was detected. The microhardness of the joint distribution also
has shown microhardness increasing in the HAZ of two base metals
and a varying microhardness in fusion zone.
Abstract: Urban Search and Rescue (USAR) is a functional
capability that has been developed to allow the United Kingdom Fire
and Rescue Service to deal with ‘major incidents’ primarily involving
structural collapse. The nature of the work undertaken by USAR
means that staying out of a damaged or collapsed building structure is
not usually an option for search and rescue personnel. As a result
there is always a risk that they themselves could become victims. For
this paper, a systematic and investigative review using desk research
was undertaken to explore the role which structural engineering can
play in assisting search and rescue personnel to conduct structural
assessments when in the field. The focus is on how search and rescue
personnel can assess damaged and collapsed building structures, not
just in terms of structural damage that may been countered, but also
in relation to structural stability. Natural disasters, accidental
emergencies, acts of terrorism and other extreme events can vary
significantly in nature and ferocity, and can cause a wide variety of
damage to building structures. It is not possible or, even realistic, to
provide search and rescue personnel with definitive guidelines and
procedures to assess damaged and collapsed building structures as
there are too many variables to consider. However, understanding
what implications damage may have upon the structural stability of a
building structure will enable search and rescue personnel to better judge
and quantify risk from a life-safety standpoint. It is intended that this
will allow search and rescue personnel to make informed decisions
and ensure every effort is made to mitigate risk, so that they
themselves do not become victims.
Abstract: Thin-walled elements with a matrix set on a base of
high-valuable Portland cement with dispersed reinforcement from
alkali-resistant glass fibres are used in a range of applications as
claddings of buildings and infrastructure constructions as well as
various architectural elements of residential buildings.
Even though their elementary thickness and therefore total weight
is quite low, architects and building companies demand on even
further decreasing of the bulk density of these fibre-cement elements
for the reason of loading elimination of connected superstructures
and easier assembling in demand conditions.
By the means of various kinds of light-weight aggregates it is
possible to achieve light-weighing of these composite elements.
From the range of possible fillers with different material properties
granulated expanded glass worked the best.
By the means of laboratory testing an effect of two fillers based on
expanded glass on the fibre reinforced cement composite was
verified.
Practical applicability was tested in the production of commonly
manufactured glass fibre reinforced concrete elements, such as
channels for electrical cable deposition, products for urban equipment
and especially various cladding elements.
Even though these are not structural elements, it is necessary to
evaluate also strength characteristics and resistance to environment
for their durability in certain applications.
Abstract: The Malaysian government had consistently revived
its campaign for “Buy Malaysian Goods” from time to time. The
purpose of the campaign is to remind consumers to be ethnocentric
and patriotic when purchasing product and services. This is necessary
to ensure high demand for local products and services compared to
foreign products. However, the decline of domestic investment in
2012 has triggered concern for the Malaysian economy. Hence, this
study attempts to determine the drivers of actual purchasing behavior,
intention to purchase domestic products and ethnocentrism. The
study employs the cross-sectional primary data, self-administered on
household, selected using stratified random sampling in four
Malaysian regions. A nine factor driver of actual domestic purchasing
behavior (culture openness, conservatism, collectivism, patriotism,
control belief, interest in foreign travel, attitude, ethnocentrism and
intention) were measured utilizing 60 items, using 7-point Likertscale.
From 1000 questionnaires distributed, a sample of 486 were
returned representing 48.6 percent response rate. From the fit
generated structural model (SEM analysis), it was found that the
drivers of actual purchase behavior are collectivism, cultural
openness and patriotism; the drivers of intention to purchase
domestic product are attitude, control belief, collectivism and
conservatism; and drivers of ethnocentrism are cultural openness,
control belief, foreign travel and patriotism. It also shows that
Malaysian consumers scored high in ethnocentrism and patriotism.
The findings are discussed in the perspective of its implication to
Malaysian National Agenda.
Abstract: In this work, we report, a systematic study on the
structural and optical properties of Pr-doped ZnO nanostructures and
PVA:Zn98Pr2O polymer matrix nanocomposites free standing films.
These particles are synthesized through simple wet chemical route
and solution casting technique at room temperature, respectively.
Structural studies carried out by X-ray diffraction method confirm
that the prepared pure ZnO and Pr doped ZnO nanostructures are in
hexagonal wurtzite structure and the microstrain is increased upon
doping. TEM analysis reveals that the prepared materials are in sheet
like nature. Absorption spectra show free excitonic absorption band
at 370 nm and red shift for the Pr doped ZnO nanostructures. The
PVA:Zn98Pr2O composite film exhibits both free excitonic and PVA
absorption bands at 282 nm. Fourier transform infrared spectral
studies confirm the presence of A1 (TO) and E1 (TO) modes of Zn-O
bond vibration and the formation of polymer composite materials.
Abstract: Skin aging is a slow multifactorial process influenced
by both internal as well as external factors. Ultra-violet radiations
(UV), diet, smoking and personal habits are the most common
environmental factors that affect skin aging. Fat contents and fibrous
proteins as collagen and elastin are core internal structural
components. The direct influence of UV on elastin integrity and
health is central on aging of skin especially by time. The deposition
of abnormal elastic material is a major marker in a photo-aged skin.
Searching for compounds that may protect against cutaneous photodamage
is exceedingly valued. Retinoids and alpha hydroxy acids
have been endorsed by some researchers as possible candidates for
protecting and or repairing the effect of UV damaged skin. For
consolidating a better system of anti- and protective effects of such
anti-aging agents, we evaluated the combinatory effects of various
dosages of lactic acid and retinol on the dermal fibroblast’s elastin
levels exposed to UV. The UV exposed cells showed significant
reduction in the elastin levels. A combination of drugs with a higher
concentration of lactic acid (30 -35 mM) and a lower concentration of
retinol (10-15mg/mL) showed to work better in maintaining elastin
concentration in UV exposed cells. We assume this preservation
could be the result of increased tropo-elastin gene expression
stimulated by retinol whereas lactic acid probably repaired the UV
irradiated damage by enhancing the amount and integrity of the
elastin fibers.
Abstract: The traditional Turkish houses becoming unusable are
a result of the deterioration of the balanced interaction between users
and house (human and house) continuing during the history.
Especially depending upon the change in social structure, the houses
becoming neglected do not meet the desires of the users and do not
have the meaning but the shelter are becoming unusable and are
being destroyed.
A conservation policy should be developed and renovations should
be made in order to pass the traditional houses carrying the quality of
a cultural and historical document presenting the social structure, the
lifestyle and the traditions of its own age to the next generations and
to keep them alive.