Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: Identification of cancer genes that might anticipate
the clinical behaviors from different types of cancer disease is
challenging due to the huge number of genes and small number of
patients samples. The new method is being proposed based on
supervised learning of classification like support vector machines
(SVMs).A new solution is described by the introduction of the
Maximized Margin (MM) in the subset criterion, which permits to
get near the least generalization error rate. In class prediction
problem, gene selection is essential to improve the accuracy and to
identify genes for cancer disease. The performance of the new
method was evaluated with real-world data experiment. It can give
the better accuracy for classification.
Abstract: In this paper we consider a nonlinear feedback control called augmented automatic choosing control (AACC) for nonlinear systems with constrained input. Constant terms which arise from section wise linearization of a given nonlinear system are treated as coefficients of a stable zero dynamics.Parameters included in the control are suboptimally selectedby extremizing a combination of Hamiltonian and Lyapunov functions with the aid of the genetic algorithm. This approach is applied to a field excitation control problem of power system to demonstrate the splendidness of the AACC. Simulation results show that the new controller can improve performance remarkably well.
Abstract: In this paper, we validate crater detection in moon surface image using FLDA. This proposal assumes that it is applied to SLIM (Smart Lander for Investigating Moon) project aiming at the pin-point landing to the moon surface. The point where the lander should land is judged by the position relations of the craters obtained via camera, so the real-time image processing becomes important element. Besides, in the SLIM project, 400kg-class lander is assumed, therefore, high-performance computers for image processing cannot be equipped. We are studying various crater detection methods such as Haar-Like features, LBP, and PCA. And we think these methods are appropriate to the project, however, to identify the unlearned images obtained by actual is insufficient. In this paper, we examine the crater detection using FLDA, and compare with the conventional methods.
Abstract: A new and cost effective RP-HPLC method was
developed and validated for simultaneous analysis of non steroidal
anti inflammatory dugs Diclofenac sodium (DFS), Flurbiprofen
(FLP) and an opioid analgesic Tramadol (TMD) in advanced drug
delivery systems (Liposome and Microcapsules), marketed brands
and human plasma. Isocratic system was employed for the flow of
mobile phase consisting of 10 mM sodium dihydrogen phosphate
buffer and acetonitrile in molar ratio of 67: 33 with adjusted pH of
3.2. The stationary phase was hypersil ODS column (C18, 250×4.6
mm i.d., 5 μm) with controlled temperature of 30 C°. DFS in
liposomes, microcapsules and marketed drug products was
determined in range of 99.76-99.84%. FLP and TMD in
microcapsules and brands formulation were 99.78 - 99.94 % and
99.80 - 99.82 %, respectively. Single step liquid-liquid extraction
procedure using combination of acetonitrile and trichloroacetic acid
(TCA) as protein precipitating agent was employed. The detection
limits (at S/N ratio 3) of quality control solutions and plasma samples
were 10, 20, and 20 ng/ml for DFS, FLP and TMD, respectively.
The Assay was acceptable in linear dynamic range. All other
validation parameters were found in limits of FDA and ICH method
validation guidelines. The proposed method is sensitive, accurate and
precise and could be applicable for routine analysis in
pharmaceutical industry as well as in human plasma samples for
bioequivalence and pharmacokinetics studies.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: Web-based systems have become increasingly
important due to the fact that the Internet and the World Wide Web
have become ubiquitous, surpassing all other technological
developments in our history. The Internet and especially companies
websites has rapidly evolved in their scope and extent of use, from
being a little more than fixed advertising material, i.e. a "web
presences", which had no particular influence for the company's
business, to being one of the most essential parts of the company's
core business.
Traditional software engineering approaches with process models
such as, for example, CMM and Waterfall models, do not work very
well since web system development differs from traditional
development. The development differs in several ways, for example,
there is a large gap between traditional software engineering designs
and concepts and the low-level implementation model, many of the
web based system development activities are business oriented (for
example web application are sales-oriented, web application and
intranets are content-oriented) and not engineering-oriented.
This paper aims to introduce Increment Iterative extreme
Programming (IIXP) methodology for developing web based
systems. In difference to the other existence methodologies, this
methodology is combination of different traditional and modern
software engineering and web engineering principles.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: Pure phase gallosilicate nitrite sodalite has been synthesized in a single step by low temperature (373 oK) hydrothermal technique. The product obtained was characterized using a combination of techniques including X-ray powder diffraction, IR, Raman spectroscopy, SEM, MAS NMR spectroscopy as well as thermogravimetry. Sodalite with an ideal composition was obtained after synthesis at 3730K and seven days duration using alkaline medium. The structural features of the Na8[GaSiO4]6(NO2)2 sodalite were investigated by IR, MAS NMR spectroscopy of 29Si and 23Na nuclei and by Reitveld refinement of X-ray powder diffraction data. The crystal structure of this sodalite has been refined in the space group P 4 3n; with a cell parameter 8.98386Å, V= 726.9 Å, (Rwp= 0.077 and Rp=0.0537) and Si-O-Ga angle is found to be 132.920 . MAS NMR study confirms complete ordering of Si and Ga in the gallosilicate framework. The surface area of single entity with stoichiometry Na8[GaSiO4]6(NO2)2 was found to be 8.083 x10-15 cm2/g.
Abstract: This paper develops a pedometer with a three-axis acceleration sensor that can be placed with any angle. The proposed pedometer measures the number of steps while users walk, jog or run. It can be worn on users’ waistband or placed within pocket or backpack. The work address to improve on the general pedometers, which can only be used in a single direction or can only count of steps without the continuous exercise judgment mechanism. Finally, experimental results confirm the superior performance of the proposed pedometer.
Abstract: The unanticipated destruct of more of the steel moment frames in Northridge earthquake, altered class of regard to the beamto- column connections in moment frames. Panel zone is one the significant part of joints which, it-s stiffness and rigidity has an important effect on the behavior and ductility of the frame. Specifically that behavior of panel zone has a very significant effect on the special moment frames. In this paper , meanwhile the relations for modeling of panel zone in frames are expressed , special moment frames with different spans and stories were studied in the way of performance-based design. The frames designed in according with Iranian steel building code. The effect of panel zone is also considered and in the case of non-existence of performance level, by changing in intimacies and parameter of panel zone, performance level is considered.
Abstract: In this paper two different Antilock braking system (ABS) are simulated and compared. One is the ordinary hydraulic ABS system which we call it ABS and the other is Electromagnetic Antilock braking system which is called (EMABS) the basis of performance of an EMABS is based upon Electromagnetic force. In this system there is no need to use servo hydraulic booster which are used in ABS system. In EMABS to generate the desired force we have use a magnetic relay which works with an input voltage through an air gap (g). The generated force will be amplified by the relay arm, and is applied to the brake shoes and thus the braking torque is generated. The braking torque is proportional to the applied electrical voltage E. to adjust the braking torque it is only necessary to regulate the electrical voltage E which is very faster and has a much smaller time constant T than the ABS system. The simulations of these two different ABS systems are done with MATLAB/SIMULINK software and the superiority of the EMABS has been shown.
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.
Abstract: A novel application of neural network approach to
fault classification and fault location of Medium voltage cables is
demonstrated in this paper. Different faults on a protected cable
should be classified and located correctly. This paper presents the use
of neural networks as a pattern classifier algorithm to perform these
tasks. The proposed scheme is insensitive to variation of different
parameters such as fault type, fault resistance, and fault inception
angle. Studies show that the proposed technique is able to offer high
accuracy in both of the fault classification and fault location tasks.
Abstract: Prediction of sinusoidal signals with time-varying
frequencies has been an important research topic in power electronics
systems. To solve this problem, we propose a new fuzzy
predictive filtering scheme, which is based on a Finite Impulse
Response (FIR) filter bank. Fuzzy logic is introduced here to provide
appropriate interpolation of individual filter outputs. Therefore,
instead of regular 'hard' switching, our method has the advantageous
'soft' switching among different filters. Simulation
comparisons between the fuzzy predictive filtering and conventional
filter bank-based approach are made to demonstrate that the
new scheme can achieve an enhanced prediction performance for
slowly changing sinusoidal input signals.
Abstract: In this paper we present a study of the impact of connection schemes on the performance of iterative decoding of Generalized Parallel Concatenated block (GPCB) constructed from one step majority logic decodable (OSMLD) codes and we propose a new connection scheme for decoding them. All iterative decoding connection schemes use a soft-input soft-output threshold decoding algorithm as a component decoder. Numerical result for GPCB codes transmitted over Additive White Gaussian Noise (AWGN) channel are provided. It will show that the proposed scheme is better than Hagenauer-s scheme and Lucas-s scheme [1] and slightly better than the Pyndiah-s scheme.
Abstract: Nano fibers produced by electrospinning are of industrial and scientific attention due to their special characteristics such as long length, small diameter and high surface area. Applications of electrospun structures in nanotechnology are included tissue scaffolds, fibers for drug delivery, composite reinforcement, chemical sensing, enzyme immobilization, membrane-based filtration, protective clothing, catalysis, solar cells, electronic devices and others. Many polymer and ceramic precursor nano fibers have been successfully electrospun with diameters in the range from 1 nm to several microns. The process is complex so that fiber diameter is influenced by various material, design and operating parameters. The objective of this work is to apply genetic algorithm on the parameters of electrospinning which have the most significant effect on the nano fiber diameter to determine the optimum parameter values before doing experimental set up. Effective factors including initial polymer concentration, initial jet radius, electrical potential, relaxation time, initial elongation, viscosity and distance between nozzle and collector are considered to determine finest diameter which is selected by user.
Abstract: The research was designed to examine the relationship
between the development of muscle fatigue and the effect it has on
sport performance, specifically during maximal voluntary
contraction. This kind of this investigation using simultaneous
electrophysiological and mechanical recordings, based on advanced
mathematical processing, allows us to get parameters, and indexes in
a short time, and finally, the mapping to use for the thorough
investigation of the muscle contraction force, respectively the
phenomenon of local muscle fatigue, both for athletes and other
subjects.
Abstract: The ongoing effort to develop an in-house
compressible solver with multi-disciplinary physics is presented in
this paper. Basic compressible solver combined with IBM technique
provides us an effective numerical tool able to tackle the physics
phenomena and especially physic phenomena involved in Solid
Rocket Motors (SRMs). Main principles are introduced step by step
describing its implementation. This paper sheds light on the whole
potentiality of our proposed numerical model and we strongly believe
a way to introduce multi-physics mechanisms strongly coupled is
opened to ablation in nozzle, fluid/structure interaction and burning
propellant surface with time.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.