Abstract: A microchannel with two inlets and two outlets was tested as a potential reactor to carry out two-phase catalytic phase transfer reaction with phase separation at the exit of the microchannel. The catalytic phase transfer reaction between benzyl chloride and sodium sulfide was chosen as a model reaction. The effect of operational time on the conversion was studied. By utilizing a multiphase parallel flow inside the microchannel reactor with the aid of a guideline structure, the catalytic phase reaction followed by phase separation could be ensured. The organic phase could be separated completely from one exit and part of the aqueous phase was separated purely and could be reused with slightly affecting the catalytic phase transfer reaction.
Abstract: Since the 1980s, banks and financial service institutions have been running in an endless race of innovation to cope with the advancing technology, the fierce competition, and the more sophisticated and demanding customers. In order to guide their innovation efforts, several researches were conducted to identify the success and failure factors of new financial services. These mainly included organizational factors, marketplace factors and new service development process factors. They almost all emphasized the importance of customer and market orientation as a response to the highly perceptual and intangible characteristics of financial services. However, they deemphasized the critical characteristics of high involvement of risk and close correlation with the economic conditions, a factor that heavily contributed to the Global financial Crisis of 2008. This paper reviews the success and failure factors of new financial services. It then adds new perspectives emerging from the analysis of the role of innovation in the global financial crisis.
Abstract: Analysis of the elastic scattering of protons on 6,7Li
nuclei has been done in the framework of the optical model at the
beam energies up to 50 MeV. Differential cross sections for the 6,7Li +
p scattering were measured over the proton laboratory–energy range
from 400 to 1050 keV. The elastic scattering of 6,7Li+p data at
different proton incident energies have been analyzed using singlefolding
model. In each case the real potential obtained from the
folding model was supplemented by a phenomenological imaginary
potential, and during the fitting process the real potential was
normalized and the imaginary potential optimized. Normalization
factor NR is calculated in the range between 0.70 and 0.84.
Abstract: With the development of virtual communities, there is
an increase in the number of members in Virtual Communities (VCs).
Many join VCs with the objective of sharing their knowledge and
seeking knowledge from others. Despite the eagerness of sharing
knowledge and receiving knowledge through VCs, there is no
standard of assessing ones knowledge sharing capabilities and
prospects of knowledge sharing. This paper developed a vector space
model to assess the knowledge sharing prospect of VC users.
Abstract: Term Extraction, a key data preparation step in Text
Mining, extracts the terms, i.e. relevant collocation of words,
attached to specific concepts (e.g. genetic-algorithms and decisiontrees
are terms associated to the concept “Machine Learning" ). In
this paper, the task of extracting interesting collocations is achieved
through a supervised learning algorithm, exploiting a few
collocations manually labelled as interesting/not interesting. From
these examples, the ROGER algorithm learns a numerical function,
inducing some ranking on the collocations. This ranking is optimized
using genetic algorithms, maximizing the trade-off between the false
positive and true positive rates (Area Under the ROC curve). This
approach uses a particular representation for the word collocations,
namely the vector of values corresponding to the standard statistical
interestingness measures attached to this collocation. As this
representation is general (over corpora and natural languages),
generality tests were performed by experimenting the ranking
function learned from an English corpus in Biology, onto a French
corpus of Curriculum Vitae, and vice versa, showing a good
robustness of the approaches compared to the state-of-the-art Support
Vector Machine (SVM).
Abstract: The permanent magnet synchronous motor (PMSM) is
very useful in many applications. Vector control of PMSM is popular
kind of its control. In this paper, at first an optimal vector control for
PMSM is designed and then results are compared with conventional
vector control. Then, it is assumed that the measurements are noisy
and linear quadratic Gaussian (LQG) methodology is used to filter
the noises. The results of noisy optimal vector control and filtered
optimal vector control are compared to each other. Nonlinearity of
PMSM and existence of inverter in its control circuit caused that the
system is nonlinear and time-variant. With deriving average model,
the system is changed to nonlinear time-invariant and then the
nonlinear system is converted to linear system by linearization of
model around average values. This model is used to optimize vector
control then two optimal vector controls are compared to each other.
Simulation results show that the performance and robustness to noise
of the control system has been highly improved.
Abstract: Light is one of the most important qualitative and
symbolic factors and has a special position in architecture and urban
development in regard to practical function. The main function of
light, either natural or artificial, is lighting up the environment and
the constructional forms which is called lighting. However, light is
used to redefine the urban spaces by architectural genius with regard
to three aesthetic, conceptual and symbolic factors. In architecture
and urban development, light has a function beyond lighting up the
environment, and the designers consider it as one of the basic
components. The present research aims at studying the function of
light and color in architectural view and their effects in buildings.
Abstract: This paper deals with the development of a Jacobean model for a 4-axes indigenously developed scara robot arm in the laboratory. This model is used to study the relation between the velocities and the forces in the robot while it is doing the pick and place operation.
Abstract: This research presented in this paper is an on-going
project of an application of neural network and fuzzy models to
evaluate the sociological factors which affect the educational
performance of the students in Sri Lanka. One of its major goals is to
prepare the grounds to device a counseling tool which helps these
students for a better performance at their examinations, especially at
their G.C.E O/L (General Certificate of Education-Ordinary Level)
examination. Closely related sociological factors are collected as raw
data and the noise of these data are filtered through the fuzzy
interface and the supervised neural network is being utilized to
recognize the performance patterns against the chosen social factors.
Abstract: Demand of energy is increasing faster than the
generation. It leads shortage of power in all sectors of society. At
peak hours this shortage is higher. Unless we utilize energy efficient
technology, it is very difficult to minimize the shortage of energy. So
energy efficiency program and energy conservation has an important
role. Energy efficient technologies are cost intensive hence it is
always not possible to implement in country like India. In the recent
study, an educational building with operating hours from 10:00 a.m.
to 05:00 p.m. has been selected to quantify the possibility of lighting
energy conservation. As the operating hour is in daytime, integration
of daylight with artificial lighting system will definitely reduce the
lighting energy consumption. Moreover the initial investment has
been given priority and hence the existing lighting installation was
unaltered. An automatic controller has been designed which will be
operated as a function of daylight through windows and the lighting
system of the room will function accordingly. The result of the study
of integrating daylight gave quite satisfactory for visual comfort as
well as energy conservation.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: Batch adsorption of recalcitrant melanoidin using the abundantly available coal fly ash was carried out. It had low specific surface area (SBET) of 1.7287 m2/g and pore volume of 0.002245 cm3/g while qualitative evaluation of the predominant phases in it was done by XRD analysis. Colour removal efficiency was found to be dependent on various factors studied. Maximum colour removal was achieved around pH 6, whereas increasing sorbent mass from 10g/L to 200 g/L enhanced colour reduction from 25% to 86% at 298 K. Spontaneity of the process was suggested by negative Gibbs free energy while positive values for enthalpy change showed endothermic nature of the process. Non-linear optimization of error functions resulted in Freundlich and Redlich-Peterson isotherms describing sorption equilibrium data best. The coal fly ash had maximum sorption capacity of 53 mg/g and could thus be used as a low cost adsorbent in melanoidin removal.
Abstract: This paper proposes an effective algorithm approach to hybrid control systems combining fuzzy logic and conventional control techniques of controlling the speed of induction motor assumed to operate in high-performance drives environment. The introducing of fuzzy logic in the control systems helps to achieve good dynamical response, disturbance rejection and low sensibility to parameter variations and external influences. Some fundamentals of the fuzzy logic control are preliminary illustrated. The developed control algorithm is robust, efficient and simple. It also assures precise trajectory tracking with the prescribed dynamics. Experimental results have shown excellent tracking performance of the proposed control system, and have convincingly demonstrated the validity and the usefulness of the hybrid fuzzy controller in high-performance drives with parameter and load uncertainties. Satisfactory performance was observed for most reference tracks.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: The Aggregate Production Plan (APP) is a schedule of
the organization-s overall operations over a planning horizon to
satisfy demand while minimizing costs. It is the baseline for any
further planning and formulating the master production scheduling,
resources, capacity and raw material planning. This paper presents a
methodology to model the Aggregate Production Planning problem,
which is combinatorial in nature, when optimized with Genetic
Algorithms. This is done considering a multitude of constraints of
contradictory nature and the optimization criterion – overall cost,
made up of costs with production, work force, inventory, and
subcontracting. A case study of substantial size, used to develop the
model, is presented, along with the genetic operators.
Abstract: This article considers with the influence of selected economic indicators for the development of the Zlin region. Development of the region is mainly influenced by business entities which are located in the region, as well as investors who contribute to the development of regions. For the development of the region it is necessary for skilled workers remain in the region and not to leave these skilled workers. The above-mentioned and other factors are affecting the development of each region.
Abstract: This research aims to study the lead pollution in the air of Babylon governorate that resulted generally from vehicles exhausts in addition to industrial and human activities.Vehicles number in Babylon governorate increased significantly after year 2003 that resulted with increase in lead emissions into the air.Measurement of lead emissions was done in seven stations distributed randomly in Babylon governorate. These stations where located in Industrial (Al-Sena'ay) Quarter, 60 street (near to Babylon sewer directorate), 40 Street (near to the first intersection), Al-Hashmia city, Al-Mahaweel city, , Al- Musayab city in addition to another station in Sayd Idris village belong to Abugharaq district (Agricultural station for comparison). The measured concentrations in these stations were compared with the standard limits of Environmental Protection Agency EPA (2 μg /m3). The results of this study showed that the average of lead concentrations ,in Babylon governorate during year 2010, was (3.13 μg/m3) which was greater than standard limits (2 μg/m3). The maximum concentration of lead was (6.41 μg / m3) recorded in the Industrial (Al-Sena'ay) Quarter during April month, while the minimum concentrations was (0.36 μg / m3) recorded in the agricultural station (Abugharaq) during December month.
Abstract: The paper investigates the potential of support vector
machines and Gaussian process based regression approaches to
model the oxygen–transfer capacity from experimental data of
multiple plunging jets oxygenation systems. The results suggest the
utility of both the modeling techniques in the prediction of the
overall volumetric oxygen transfer coefficient (KLa) from operational
parameters of multiple plunging jets oxygenation system. The
correlation coefficient root mean square error and coefficient of
determination values of 0.971, 0.002 and 0.945 respectively were
achieved by support vector machine in comparison to values of
0.960, 0.002 and 0.920 respectively achieved by Gaussian process
regression. Further, the performances of both these regression
approaches in predicting the overall volumetric oxygen transfer
coefficient was compared with the empirical relationship for multiple
plunging jets. A comparison of results suggests that support vector
machines approach works well in comparison to both empirical
relationship and Gaussian process approaches, and could successfully
be employed in modeling oxygen-transfer.
Abstract: A mammography image is composed of low contrast area where the breast tissues and the breast abnormalities such as microcalcification can hardly be differentiated by the medical practitioner. This paper presents the application of active contour models (Snakes) for the segmentation of microcalcification in mammography images. Comparison on the microcalcifiation areas segmented by the Balloon Snake, Gradient Vector Flow (GVF) Snake, and Distance Snake is done against the true value of the microcalcification area. The true area value is the average microcalcification area in the original mammography image traced by the expert radiologists. From fifty images tested, the result obtained shows that the accuracy of the Balloon Snake, GVF Snake, and Distance Snake in segmenting boundaries of microcalcification are 96.01%, 95.74%, and 95.70% accuracy respectively. This implies that the Balloon Snake is a better segmentation method to locate the exact boundary of a microcalcification region.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.