Abstract: Lighting upgrades involve relatively lower costs which
allow the benefits to be spread more widely than is possible with any
other energy efficiency measure. In order to popularize the adoption of
CFL in Taiwan, the authority proposes to implement a new energy efficient lamp comparative label system. The current study was
accordingly undertaken to investigate the factors affecting the performance and the deviation of actual and labeled performance of
commercially available integrated CFLs. In this paper, standard test
methods to determine the electrical and photometric performances of
CFL were developed based on CIE 84-1989 and CIE 60901-1987,
then 55 selected CFLs from market were tested. The results show that
with higher color temperature of CFLs lower efficacy are achieved. It
was noticed that the most packaging of CFL often lack the information of Color Rendering Index. Also, there was no correlation between
price and performance of the CFLs was indicated in this work. The results of this paper might help consumers to make more informed
CFL-purchasing decisions.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.
Abstract: Multi-dimensional principal component analysis
(PCA) is the extension of the PCA, which is used widely as the
dimensionality reduction technique in multivariate data analysis, to
handle multi-dimensional data. To calculate the PCA the singular
value decomposition (SVD) is commonly employed by the reason of
its numerical stability. The multi-dimensional PCA can be calculated
by using the higher-order SVD (HOSVD), which is proposed by
Lathauwer et al., similarly with the case of ordinary PCA. In this
paper, we apply the multi-dimensional PCA to the multi-dimensional
medical data including the functional independence measure (FIM)
score, and describe the results of experimental analysis.
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: On a such wide-area environment as a Grid, data
placement is an important aspect of distributed database systems. In
this paper, we address the problem of initial placement of database
no-replicated fragments in Grid architecture. We propose a graph
based approach that considers resource restrictions. The goal is to
optimize the use of computing, storage and communication
resources. The proposed approach is developed in two phases: in the
first phase, we perform fragment grouping using knowledge about
fragments dependency and, in the second phase, we determine an
efficient placement of the fragment groups on the Grid. We also
show, via experimental analysis that our approach gives solutions
that are close to being optimal for different databases and Grid
configurations.
Abstract: Renewable and non-renewable resource constraints have been vast studied in theoretical fields of project scheduling problems. However, although cumulative resources are widespread in practical cases, the literature on project scheduling problems subject to these resources is scant. So in order to study this type of resources more, in this paper we use the framework of a resource constrained project scheduling problem (RCPSP) with finish-start precedence relations between activities and subject to the cumulative resources in addition to the renewable resources. We develop a branch and bound algorithm for this problem customizing precedence tree algorithm of RCPSP. We perform extensive experimental analysis on the algorithm to check its effectiveness and performance for solving different instances of the problem in question.
Abstract: Abrasive waterjet cutting (AWJ) is a highly efficient
method for cutting almost any type of material. When holes shall be
cut the waterjet first needs to pierce the material.This paper presents a
vast experimental analysis of piercing parameters effect on piercing
time. Results from experimentation on feed rates, work piece
thicknesses, abrasive flow rates, standoff distances and water
pressure are also presented as well as studies on three methods for
dynamic piercing. It is shown that a large amount of time and
resources can be saved by choosing the piercing parameters in a
correct way. The large number of experiments puts demands on the
experimental setup. An automated experimental setup including
piercing detection is presented to enable large series of experiments
to be carried out efficiently.