Abstract: Different numerical methods are employed and developed for simulating interfacial flows. A large range of applications belong to this group, e.g. two-phase flows of air bubbles in water or water drops in air. In such problems surface tension effects often play a dominant role. In this paper, various models of surface tension force for interfacial flows, the CSF, CSS, PCIL and SGIP models have been applied to simulate the motion of small air bubbles in water and the results were compared and reviewed. It has been pointed out that by using SGIP or PCIL models, we are able to simulate bubble rise and obtain results in close agreement with the experimental data.
Abstract: A phorbol-12-myristate-13-acetate (TPA) is a synthetic analogue of phorbol ester (PE), a natural toxic compound of Euphorbiaceae plant. The oil extracted from plants of this family is useful source for primarily biofuel. However this oil might also be used as a foodstuff due to its significant nutrition content. The limitations for utilizing the oil as a foodstuff are mainly due to a toxicity of PE. Currently, a majority of PE detoxification processes are expensive as include multi steps alcohol extraction sequence.
Ozone is considered as a strong oxidative agent. It reacts with PE by attacking the carbon-carbon double bond of PE. This modification of PE molecular structure yields a non toxic ester with high lipid content.
This report presents data on development of simple and cheap PE detoxification process with water application as a buffer and ozone as reactive component. The core of this new technique is an application for a new microscale plasma unit to ozone production and the technology permits ozone injection to the water-TPA mixture in form of microbubbles.
The efficacy of a heterogeneous process depends on the diffusion coefficient which can be controlled by contact time and interfacial area. The low velocity of rising microbubbles and high surface to volume ratio allow efficient mass transfer to be achieved during the process. Direct injection of ozone is the most efficient way to process with such highly reactive and short lived chemical.
Data on the plasma unit behavior are presented and the influence of gas oscillation technology on the microbubble production mechanism has been discussed. Data on overall process efficacy for TPA degradation is shown.
Abstract: Air bubbles have been detected in human circulation
of end-stage renal disease patients who are treated by hemodialysis.
The consequence of air embolism, air bubbles, is under recognized
and usually overlooked in daily practice. This paper shows results of
a capacitor based detection method that capable of detecting the
presence of air bubbles in the blood stream in different frequencies.
The method is based on a parallel plates capacitor made of platinum
with an area of 1.5 cm2 and a distance between the two plates is 1cm.
The dielectric material used in this capacitor is Dextran70 solution
which mimics blood rheology. Simulations were carried out using
RC circuit at two frequencies 30Hz and 3 kHz and results compared
with experiments and theory. It is observed that by injecting air
bubbles of different diameters into the device, there were significant
changes in the capacitance of the capacitor. Furthermore, it is
observed that the output voltage from the circuit increased with
increasing air bubble diameter. These results demonstrate the
feasibility of this approach in improving air bubble detection in
Hemodialysis.
Abstract: The theoretical investigation is carried out to describe
the effect of increase of pressure waves amplitude in clean and bubbly liquid. The goal of the work is to capture the regime of multiple magnification of acoustic and shock waves in the liquid,
which enables to get appropriate conditions to enlarge collapses of
micro-bubbles. The influence of boundary conditions and frequency
of the governing acoustic field is studied for the case of the
cylindrical acoustic resonator. It has been observed the formation of
standing waves with large amplitude at resonant frequencies. The
interaction of the compression wave with gas and vapor bubbles is
investigated for the convergent channel. It is shown theoretically that
the chemical reactions, which occur inside gas bubbles, provide additional impulse to the wave, that affect strongly on the collapses
of the vapor bubbles
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: Microbubbbles incorporating ultrasound have been used to increase the efficacy of targeted drug delivery, because microstreaming induced by cavitating bubbles affects the drug perfusion into the target cells and tissues. In order to clarify the physical effects of microstreaming on drug perfusion into tissues, a preliminary experimental study of perfusion enhancement by a stably oscillating microbubble was performed. Microstreaming was induced by an oscillating bubble at 15 kHz, and perfusion of dye into an agar phantom was optically measured by histology on agar phantom. Surface color intensity and the penetration length of dye in the agar phantom were increased more than 70% and 30%, respectively, due to the microstreaming induced by an oscillating bubble. The mass of dye perfused into a tissue phantom for 30 s was increased about 80% in the phantom with an oscillating bubble. This preliminary experiment shows the physical effects of steady streaming by an oscillating bubble can enhance the drug perfusion into the tissues while minimizing the biological effects.
Abstract: The hydrodynamic processes in bubbly liquid flowing
in tubes and nozzles are studied theoretically and numerically. The
principal regularities of non-stationary processes of boiling liquid
outflow are established under conditions of experiments when the
depressurization of a tube with high pressure inside occurs. The
steady-state solution of bubbly liquid flow in the nozzle of round
cross section with high pressure and temperature conditions inside
bubbles is studied accounting for phase transition and chemical
reactions.
Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.