Abstract: The present study is concerned with the free
convective two dimensional flow and heat transfer, within the
framework of Boussinesq approximation, in anisotropic fluid filled
porous rectangular enclosure subjected to end-to-end temperature
difference have been investigated using Lattice Boltzmann method
fornon-Darcy flow model. Effects of the moving lid direction (top,
bottom, left, and right wall moving in the negative and positive x&ydirections),
number of moving walls (one or two opposite walls), the
sliding wall velocity, and four different constant temperatures
opposite walls cases (two surfaces are being insulated and the
twoother surfaces areimposed to be at constant hot and cold
temperature)have been conducted. The results obtained are discussed
in terms of the Nusselt number, vectors, contours, and isotherms.
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: An on-demand routing protocol for wireless ad hoc
networks is one that searches for and attempts to discover a route to
some destination node only when a sending node originates a data
packet addressed to that node. In order to avoid the need for such a
route discovery to be performed before each data packet is sent, such
routing protocols must cache routes previously discovered. This
paper presents an analysis of the effect of intelligent caching in a non
clustered network, using on-demand routing protocols in wireless ad
hoc networks. The analysis carried out is based on the Dynamic
Source Routing protocol (DSR), which operates entirely on-demand.
DSR uses the cache in every node to save the paths that are learnt
during route discovery procedure. In this implementation, caching
these paths only at intermediate nodes and using the paths from these
caches when required is tried. This technique helps in storing more
number of routes that are learnt without erasing the entries in the
cache, to store a new route that is learnt.
The simulation results on DSR have shown that this technique
drastically increases the available memory for caching the routes
discovered without affecting the performance of the DSR routing
protocol in any way, except for a small increase in end to end delay.
Abstract: In this paper, the effect of addition the dune sand powder (DSP) on development of compressive strength and hydration of cement pastes was investigated as a function of water/binder ratio, was varied, on the one hand, the percentage of DSP and on the other, the fineness of DSP. In order to understand better the pozzolanic effect of dune sand powder in cement pastes, we followed the mixtures hydration (50% Pure Lime + 50% DSP) by X-ray diffraction. These mixtures the pastes present a hydraulic setting which is due to the formation of a C-S-H phase (calcium silicate hydrate). The latter is semi-crystallized. This study is a simplified approach to that of the mixtures (80% ordinary Portland cement + 20% DSP), in which the main reaction is the fixing of the lime coming from the cement hydration in the presence of DSP, to form calcium silicate hydrate semi-crystallized of second generation. The results proved that up to (20% DSP) as Portland cement replacement could be used with a fineness of 4000 cm²/g without affecting adversely the compressive strength. After 28 days, the compressive strength at 5, 10 and 15% DSP is superior to Portland cement, with an optimum effect for a percentage of the order of 5% to 10% irrespective of the w/b ratio and fineness of DSP.
Abstract: A comparative study on the feasibility of producing instant high fibre plantain flour for diabetic fufu by blending soy residence with different plantain (Musa spp) varieties (Horn, false Horn and French), all sieved at 60 mesh, mixed in ratio of 60:40 was analyzed for their passing properties using standard analytical method. Results show that VIIIS60 had the highest peak viscosity (303.75 RVU), Trough value (182.08 RVU), final viscosity (284.50 RVU), and lowest in breakdown viscosity (79.58 RVU), set back value (88.17 RVU), peak time (4.36min), pasting temperature (81.18°C) and differed significantly (p
Abstract: Cardiac pulse-related artifacts in the EEG recorded
simultaneously with fMRI are complex and highly variable. Their
effective removal is an unsolved problem. Our aim is to develop an
adaptive removal algorithm based on the matching pursuit (MP)
technique and to compare it to established methods using a visual
evoked potential (VEP). We recorded the VEP inside the static
magnetic field of an MR scanner (with artifacts) as well as in an
electrically shielded room (artifact free). The MP-based artifact
removal outperformed average artifact subtraction (AAS) and
optimal basis set removal (OBS) in terms of restoring the EEG field
map topography of the VEP. Subsequently, a dipole model was fitted
to the VEP under each condition using a realistic boundary element
head model. The source location of the VEP recorded inside the MR
scanner was closest to that of the artifact free VEP after cleaning
with the MP-based algorithm as well as with AAS. While none of the
tested algorithms offered complete removal, MP showed promising
results due to its ability to adapt to variations of latency, frequency
and amplitude of individual artifact occurrences while still utilizing a
common template.
Abstract: This paper present a new way to find the aerodynamic characteristic equation of missile for the numerical trajectories prediction more accurate. The goal is to obtain the polynomial equation based on two missile characteristic parameters, angle of attack (α ) and flight speed (╬¢ ). First, the understudied missile is modeled and used for flow computational model to compute aerodynamic force and moment. Assume that performance range of understudied missile where range -10< α
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.
Abstract: The paper focuses on the implementation phase of the
strategy of the European Union and the national strategy of the
Czech Republic to promote academic and research staff with the
potential to produce results that provide innovation useful for
economic growth. It deals with the use of financial resources of the
Operational Program Education for Competitiveness at the
University of West Bohemia in Pilsen. The author presents an
example of two strategic projects in the field of human resources –
Excellence in Human Resources as a Source of Competitiveness and
New Excellence of Human Resources. The subject of this paper is the
potential contribution of newly recruited postdoctoral within these
projects for the University of West Bohemia in Pilsen and its internal
environment.
Abstract: Most parts of the world such as Iran are facing the excessive consumption of fertilizers, that are used to achieve high yield, but increase the cost of production of fertilizer and degradation of soil and water resources. This experiment was carried out to study the effect of PGPR and planting pattern on yield and yield components of rice (Oryza sativa L.) using split plot based on randomized complete block design with three replications in Ilam province, Iran. Bio-fertilizer including Azotobacter, Nitroxin and control treatment (without consumption) were designed as a main plot and planting pattern including 15 × 10, 15 × 15 and 15 × 20 and the number of plant in hill including 3, 4 and 5 plants in hill were considered as a sub-plots. The results showed that the effect of bio-fertilizers, planting pattern and the number of plants in hill were significant affect on yield and yield components. Interaction effect between bio-fertilizer and planting pattern had important difference on the number spikelet of panicle and harvest index. Interaction effect between bio-fertilizer and the number of plants in hill were significant affect on the number of spikelet per panicle. The maximum grain yield was obtained by inoculation with Nitroxin, planting pattern of 15 × 15 and 4 plants in hill with mean of 1110.6 g.m-2, 959.9 g.m-2 and 928.4 g.m-2, respectively.
Abstract: A study was conducted in greenhouse environment to
determine the response of five tissue-cultured date palm cultivars, Al-
Ahamad, Nabusaif, Barhee, Khalas, and Kasab to irrigation water
salinity of 1.6, 5, 10, or 20 dS/ m. The salinity level of 1.6dS/m, was
used as a control. The effects of high salinity on plant survival were
manifested at 360 days after planting (DAP) onwards. Three
cultivars, Khalas, Kasab and Barhee were able to tolerate 10 dS/m
salinity level at 24 months after the start of study. Khalas tolerated
the highest salinity level of 20 dS/ m and 'Nabusaif' was found to be the
least tolerant cv. The average heights of palms and the number of
fronds were decreased with increasing salinity levels as time
progressed.
Abstract: Copper based composites reinforced with WC and Ti
particles were prepared using planetary ball-mill. The experiment
was designed by using Taguchi technique and milling was carried out
in an air for several hours. The powder was characterized before and
after milling using the SEM, TEM and X-ray for microstructure and
for possible new phases. Microstructures show that milled particles
size and reduction in particle size depend on many parameters. The
distance d between planes of atoms estimated from X-ray powder
diffraction data and TEM image. X-ray diffraction patterns of the
milled powder did not show clearly any new peak or energy shift, but
the TEM images show a significant change in crystalline structure of
corporate on titanium in the composites.
Abstract: In the world of Peer-to-Peer (P2P) networking
different protocols have been developed to make the resource sharing
or information retrieval more efficient. The SemPeer protocol is a
new layer on Gnutella that transforms the connections of the nodes
based on semantic information to make information retrieval more
efficient. However, this transformation causes high clustering in the
network that decreases the number of nodes reached, therefore the
probability of finding a document is also decreased. In this paper we
describe a mathematical model for the Gnutella and SemPeer
protocols that captures clustering-related issues, followed by a
proposition to modify the SemPeer protocol to achieve moderate
clustering. This modification is a sort of link management for the
individual nodes that allows the SemPeer protocol to be more
efficient, because the probability of a successful query in the P2P
network is reasonably increased. For the validation of the models, we
evaluated a series of simulations that supported our results.
Abstract: One of the main trouble in a steel strip manufacturing
line is the breakage of whatever weld carried out between steel coils,
that are used to produce the continuous strip to be processed. A weld
breakage results in a several hours stop of the manufacturing line. In
this process the damages caused by the breakage must be repaired.
After the reparation and in order to go on with the production it will
be necessary a restarting process of the line. For minimizing this
problem, a human operator must inspect visually and manually each
weld in order to avoid its breakage during the manufacturing process.
The work presented in this paper is based on the Bayesian decision
theory and it presents an approach to detect, on real-time, steel strip
defective welds. This approach is based on quantifying the tradeoffs
between various classification decisions using probability and the
costs that accompany such decisions.
Abstract: There are various overlay structures that provide
efficient and scalable solutions for point and range query in a peer-topeer
network. Overlay structure based on m-Binary Search Tree
(BST) is one such popular technique. It deals with the division of the
tree into different key intervals and then assigning the key intervals to
a BST. The popularity of the BST makes this overlay structure
vulnerable to different kinds of attacks. Here we present four such
possible attacks namely index poisoning attack, eclipse attack,
pollution attack and syn flooding attack. The functionality of BST is
affected by these attacks. We also provide different security
techniques that can be applied against these attacks.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: On the basis of the linearized Phillips-Herffron model of a single-machine power system, a novel method for designing unified power flow controller (UPFC) based output feedback controller is presented. The design problem of output feedback controller for UPFC is formulated as an optimization problem according to with the time domain-based objective function which is solved by iteration particle swarm optimization (IPSO) that has a strong ability to find the most optimistic results. To ensure the robustness of the proposed damping controller, the design process takes into account a wide range of operating conditions and system configurations. The simulation results prove the effectiveness and robustness of the proposed method in terms of a high performance power system. The simulation study shows that the designed controller by Iteration PSO performs better than Classical PSO in finding the solution.
Abstract: The security of their network remains the priorities of almost all companies. Existing security systems have shown their limit; thus a new type of security systems was born: honeypots. Honeypots are defined as programs or intended servers which have to attract pirates to study theirs behaviours. It is in this context that the leurre.com project of gathering about twenty platforms was born. This article aims to specify a model of honeypots attack. Our model describes, on a given platform, the evolution of attacks according to theirs hours. Afterward, we show the most attacked services by the studies of attacks on the various ports. It is advisable to note that this article was elaborated within the framework of the research projects on honeyspots within the LABTIC (Laboratory of Information Technologies and Communication).
Abstract: Robot manipulators are highly coupled nonlinear
systems, therefore real system and mathematical model of dynamics
used for control system design are not same. Hence, fine-tuning of
controller is always needed. For better tuning fast simulation speed
is desired. Since, Matlab incorporates LAPACK to increase the speed
and complexity of matrix computation, dynamics, forward and
inverse kinematics of PUMA 560 is modeled on Matlab/Simulink in
such a way that all operations are matrix based which give very less
simulation time. This paper compares PID parameter tuning using
Genetic Algorithm, Simulated Annealing, Generalized Pattern Search
(GPS) and Hybrid Search techniques. Controller performances for all
these methods are compared in terms of joint space ITSE and
cartesian space ISE for tracking circular and butterfly trajectories.
Disturbance signal is added to check robustness of controller. GAGPS
hybrid search technique is showing best results for tuning PID
controller parameters in terms of ITSE and robustness.
Abstract: Character segmentation is an important preprocessing step for text recognition. In degraded documents, existence of touching characters decreases recognition rate drastically, for any optical character recognition (OCR) system. In this paper a study of touching Gurmukhi characters is carried out and these characters have been divided into various categories after a careful analysis.Structural properties of the Gurmukhi characters are used for defining the categories. New algorithms have been proposed to segment the touching characters in middle zone. These algorithms have shown a reasonable improvement in segmenting the touching characters in degraded Gurmukhi script. The algorithms proposed in this paper are applicable only to machine printed text.