Abstract: This study employs auto-regressive distributed lag (ARDL) bounds approach to cointegration for long run and errorcorrection modeling (ECM) for short run analysis to examine the relationship between revenue gap and economic growth for Pakistan using annual time series data over the period 1980 to 2008. The short and long run results indicate that revenue gap is statistical significant and negatively effect economic growth. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 10.406 percent within a year.
Abstract: In the Fe-3%Si sheets, grade Hi-B, with AlN and MnS
as inhibitors, the Goss grains which abnormally grow do not have a
size greater than the average size of the primary matrix. In this
heterogeneous microstructure, the size factor is not a required
condition for the secondary recrystallization. The onset of the small
Goss grain abnormal growth appears to be related to a particular
behavior of their grain boundaries, to the local texture and to the
distribution of the inhibitors. The presence and the evolution of
oriented clusters ensure to the small Goss grains a favorable
neighborhood to grow. The modified Monte-Carlo approach, which
is applied, considers the local environment of each grain. The grain
growth is dependent of its real spatial position; the matrix
heterogeneity is then taken into account. The grain growth conditions
are considered in the global matrix and in different matrixes
corresponding to A component clusters. The grain growth behaviour
is considered with introduction of energy only, energy and mobility,
energy and mobility and precipitates.
Abstract: Single crystals of Magnesium alloys such as Mg-1Al,
Mg-1Zn-0.5Y, Mg-3Li, and AZ31 alloys were successfully fabricated in this study by employing the modified Bridgman method. Single
crystals of pure Mg were also made in this study. To determine the exact orientation of crystals, Laue back-reflection method and pole figure measurement were carried out on each single crystal. Dimensions of single crystals were 10 mm in diameter and 120 mm in
length. Hardness and compression tests were conducted and the results
revealed that hardness and the strength strongly depended on the
orientation. The closer to basal one the orientation was, the higher hardness and compressive strength were. The effect of alloying was
not higher than that of orientation. After compressive deformation of single crystals, the orientation of the crystals was found to rotate and to be parallel to the basal orientation.
Abstract: This study mainly aims at assessing the level of
microbial pollution of the water used in the chair system in dental
clinics. For this purpose 36 samples have been randomly collected
from a number of dental surgeries in the city of Tripoli in Libya.
However, 32 of the samples have tested positive to microbial
pollution including 13 of the samples, which have tested positives to
Pseudomonas aeruginosa. Based on the results of the test a further
investigation of the biofilms incorporated within the dental chair
system has been conducted. The laboratory tests of biofilms with
similar design to those found in dental chairs have proved that
bacterial pollution takes place through saliva of the patients who use
the chairs, and that this saliva is rich with nutrients which provides a
suitable breeding ground for all types of bacteria.
Abstract: This paper introduces the foundations of Bayesian probability theory and Bayesian decision method. The main goal of Bayesian decision theory is to minimize the expected loss of a decision or minimize the expected risk. The purposes of this study are to review the decision process on the issue of flood occurrences and to suggest possible process for decision improvement. This study examines the problem structure of flood occurrences and theoretically explicates the decision-analytic approach based on Bayesian decision theory and application to flood occurrences in Environmental Engineering. In this study, we will discuss about the flood occurrences upon an annual maximum water level in cm, 43-year record available from 1965 to 2007 at the gauging station of Sagaing on the Ayeyarwady River with the drainage area - 120193 sq km by using Bayesian decision method. As a result, we will discuss the loss and risk of vast areas of agricultural land whether which will be inundated or not in the coming year based on the two standard maximum water levels during 43 years. And also we forecast about that lands will be safe from flood water during the next 10 years.
Abstract: The search for factors that influence user behavior has remained an important theme for both the academic and practitioner Information Systems Communities. In this paper we examine relevant user behaviors in the phase after adoption and investigate two factors that are expected to influence such behaviors, namely User Involvement (UI) and Personal Innovativeness in IT (PIIT). We conduct a field study to examine how these factors influence postadoption behavior and how they are interrelated. Building on theoretical premises and prior empirical findings, we propose and test two alternative models of the relationship between these factors. Our results reveal that the best explanation of post-adoption behavior is provided by the model where UI and PIIT independently influence post-adoption behavior. Our findings have important implications for research and practice. To that end, we offer directions for future research.
Abstract: Extensive wind tunnel tests have been conducted to
investigate the unsteady flow field over and behind a 2D model of a
660 kW wind turbine blade section in pitching motion. The surface
pressure and wake dynamic pressure variation at a distance of 1.5
chord length from trailing edge were measured by pressure
transducers during several oscillating cycles at 3 reduced frequencies
and oscillating amplitudes. Moreover, form drag and linear
momentum deficit are extracted and compared at various conditions.
The results show that the wake velocity field and surface pressure of
the model have similar behavior before and after the airfoil beyond
the static stall angle of attack. In addition, the effects of reduced
frequency and oscillation amplitudes are discussed.
Abstract: The amount and heterogeneity of data in biomedical research, notably in interdisciplinary research, requires new methods for the collection, presentation and analysis of information. Important data from laboratory experiments as well as patient trials are available but come out of distributed resources. The Charite Medical School in Berlin has established together with the German Research Foundation (DFG) a new information service center for kidney diseases and transplantation (Open European Nephrology Science Centre - OpEN.SC). The system is based on a service-oriented architecture (SOA) with main and auxiliary modules arranged in four layers. To improve the reuse and efficient arrangement of the services the functionalities are described as business processes using the standardised Business Process Execution Language (BPEL).
Abstract: The pigments covered by film-forming polymers have
opened a prospect to improve the quality of water-based printing
inks. In this study such pigments were prepared by the initiated
polymerization of styrene and methacrylate derivative monomers in
the aqueous pigment dispersions. The formation of polymer films
covering pigment cores depends on the polymerization time and the
ratio of pigment to monomers. At the time of 4 hours and the ratio of
1/10 almost pigment particles are coated by the polymer. The formed
polymer covers of pigments have the average thickness of 5.95 nm.
The size increasing percentage of the coated particles after a week is
4.5 %, about fourteen-fold lower than of the original ones. The
obtained results indicate that the coated pigments are improved
dispersion stability in water medium along with a guarantee for the
optical colour.
Abstract: Our objectives were to evaluate the effects of sire
breed, type of protein supplement, level of supplementation and sex
on wool spinning fineness (SF), its correlations with other wool
characteristics and prediction accuracy in F1 Merino crossbred lambs.
Texel, Coopworth, White Suffolk, East Friesian and Dorset rams
were mated with 500 purebred Merino dams at a ratio of 1:100 in
separate paddocks within a single management system. The F1
progeny were raised on ryegrass pasture until weaning, before forty
lambs were randomly allocated to treatments in a 5 x 2 x 2 x 2
factorial experimental design representing 5 sire breeds, 2
supplementary feeds (canola or lupins), 2 levels of supplementation
(1% or 2% of liveweight) and sex (wethers or ewes). Lambs were
supplemented for six weeks after an initial three weeks of adjustment,
wool sampled at the commencement and conclusion of the feeding
trial and analyzed for SF, mean fibre diameter (FD), coefficient of
variation (CV), standard deviation, comfort factor (CF), fibre
curvature (CURV), and clean fleece yield. Data were analyzed using
mixed linear model procedures with sire fitted as a random effect,
and sire breed, sex, supplementary feed type, level of
supplementation and their second-order interactions as fixed effects.
Sire breed (P
Abstract: The influence of copper promoters and reaction
conditions on the formation of alcohols byproducts of a common
Fischer-Tropsch synthesis used iron-based catalysts were investigated.
A good compromise of 28%Cu/FeKLaSiO2 can lead to the
optimization of an improved Fischer-Tropsch catalyst. The product
distribution shifts towards hydrocarbons with increasing the reaction
temperature, while pressure promotes the formation of alcohols. It was
found that the production of either alcohols or hydrocarbons followed
A-S-F distributions, and their α parameters were essentially different
which indicated a competition in the growing chain between the two
species. TPD after acetaldehyde adsorption gave strong evidence of
the insertion of a C1 oxygen-containing species into an alkyl chain.
Abstract: This study evaluated the microbiological quality
and the sensory characteristics of carp fillets processed by the
sousvide method when stored at 2 and 10 °C. Four different
combinations of sauced–storage were studied then stored at 2 or 10
°C was evaluate periodically sensory, microbiological and
chemical quality. Batches stored at 2 °C had lower growth rates of
mesophiles and psychrotrophs. Moreover, these counts decreased
by increasing the heating temperature and time. Staphylococcus
aureus, Bacillus cereus, Clostridium perfringens and Listeria
monocytogenes were not found in any of the samples. The heat
treatment of 90 °C for 15 min and sauced was the most effective to
ensure the safety and extend the shelf-life of sousvide carp
preserving its sensory characteristics. This study establishes the
microbiological quality of sous vide carp and emphasizes the
relevance of the raw materials, heat treatment and storage
temperature to ensure the safety of the product.
Abstract: In this study the integration of an absorption heat
pump (AHP) with the concentration section of an industrial pulp and
paper process is investigated using pinch technology. The optimum
design of the proposed water-lithium bromide AHP is then achieved
by minimizing the total annual cost. A comprehensive optimization is
carried out by relaxation of all stream pressure drops as well as heat
exchanger areas involving in AHP structure. It is shown that by
applying genetic algorithm optimizer, the total annual cost of the
proposed AHP is decreased by 18% compared to one resulted from
simulation.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: Predicting protein-protein interactions represent a key step in understanding proteins functions. This is due to the fact that proteins usually work in context of other proteins and rarely function alone. Machine learning techniques have been applied to predict protein-protein interactions. However, most of these techniques address this problem as a binary classification problem. Although it is easy to get a dataset of interacting proteins as positive examples, there are no experimentally confirmed non-interacting proteins to be considered as negative examples. Therefore, in this paper we solve this problem as a one-class classification problem using one-class support vector machines (SVM). Using only positive examples (interacting protein pairs) in training phase, the one-class SVM achieves accuracy of about 80%. These results imply that protein-protein interaction can be predicted using one-class classifier with comparable accuracy to the binary classifiers that use artificially constructed negative examples.
Abstract: Question answering (QA) aims at retrieving precise information from a large collection of documents. Most of the Question Answering systems composed of three main modules: question processing, document processing and answer processing. Question processing module plays an important role in QA systems to reformulate questions. Moreover answer processing module is an emerging topic in QA systems, where these systems are often required to rank and validate candidate answers. These techniques aiming at finding short and precise answers are often based on the semantic relations and co-occurrence keywords. This paper discussed about a new model for question answering which improved two main modules, question processing and answer processing which both affect on the evaluation of the system operations. There are two important components which are the bases of the question processing. First component is question classification that specifies types of question and answer. Second one is reformulation which converts the user's question into an understandable question by QA system in a specific domain. The objective of an Answer Validation task is thus to judge the correctness of an answer returned by a QA system, according to the text snippet given to support it. For validating answers we apply candidate answer filtering, candidate answer ranking and also it has a final validation section by user voting. Also this paper described new architecture of question and answer processing modules with modeling, implementing and evaluating the system. The system differs from most question answering systems in its answer validation model. This module makes it more suitable to find exact answer. Results show that, from total 50 asked questions, evaluation of the model, show 92% improving the decision of the system.
Abstract: The chatter is one of the major limitations of the productivity in the ball end milling process. It affects the surface roughness, the dimensional accuracy and the tool life. The aim of this research is to propose the new system to detect the chatter during the ball end milling process by using the wavelet transform. The proposed method is implemented on the 5-axis CNC machining center and the new three parameters are introduced from three dynamic cutting forces, which are calculated by taking the ratio of the average variances of dynamic cutting forces to the absolute variances of themselves. It had been proved that the chatter can be easier to detect during the in-process cutting by using the new parameters which are proposed in this research. The experimentally obtained results showed that the wavelet transform can provide the reliable results to detect the chatter under various cutting conditions.
Abstract: In this research, the main aim is to investigate the
antimicrobial effectiveness of ammonyx solutions finishing on
Sweatshirt Sport with immersion method. 60 Male healthy subjects
(football player) participated in this study. They were dressed in a
Sweatshirt for 14 days and some microbes found on them were
investigated. The antimicrobial effect of different ammonyx
solutions(1/100, 1/500, 1/1000, 1/2000 v/v solutions of Ammonyx)
on the identified microbes was studied by the zone inhabitation
method in vitro. In the next step the Sweatshirt Sports were treated
with the same different solutions of ammonyx and the antimicrobial
effectiveness was assessed by colony count method in different times
and the results were compared whit untreated ones. Some mechanical
properties of treated cotton/polyester yarn that used in Sweatshirt
Sport were measured after 30 days and were compared with
untreated one. Finally after finishing, scanning electron microscopy
(SEM) was used to compare the surfaces of the finished and
unfinished specimens. The results showed the presence of five
pathogenic microbes on Sweatshirt Sports such as Escherichia coli,
Staphylococcus aureus, Aspergillus, Mucor and Candida. The
inhalation time for treated on Sweatshirt Sports improved. The
amount of colony growth on treated clothes reduced considerably
and moreover the mechanical tests results showed no significant
deterioration effect of studies properties in comparison to the
untreated yarn. The visual examination of the SEM indicated that the
antimicrobial treatments were applied usefully to fabrics.
Abstract: In this paper, enhanced ground proximity warning simulation and validation system is designed and implemented. First, based on square grid and sub-grid structure, the global digital terrain database is designed and constructed. Terrain data searching is implemented through querying the latitude and longitude bands and separated zones of global terrain database with the current aircraft position. A combination of dynamic scheduling and hierarchical scheduling is adopted to schedule the terrain data, and the terrain data can be read and delete dynamically in the memory. Secondly, according to the scope, distance, approach speed information etc. to the dangerous terrain in front, and using security profiles calculating method, collision threat detection is executed in real-time, and provides caution and warning alarm. According to this scheme, the implementation of the enhanced ground proximity warning simulation system is realized. Simulations are carried out to verify a good real-time in terrain display and alarm trigger, and the results show simulation system is realized correctly, reasonably and stable.
Abstract: People have always needed to believe in some
supernatural power, which could explain nature phenomena.
Different kinds of religions like Christianity, Hinduism, Islam,
Buddhism have thought believers in all world, how to behave
themselves. We think the most important role of religion in modern
society most important role of religion in modern society is safety of
the People. World and traditional religion played a prominent role in
the socio-cultural progress, and in the development of man as a
spiritual being. At the heart of religious morals the belief in god and
responsibility before it lies and specifies religious and ethical values
and categories . The religion is based on ethical standards historically
developed by society, requirements and concepts, but it puts all
social and moral relations of the person in dependence on religious
values. For everything that the believer makes on a debt or a duty, he
bears moral responsibility before conscience, people and god. The
concept of value of religious morals takes the central place because
the religion from all forms of public consciousness most values is
painted as it is urged to answer vital questions. Any religion not only
considers questions of creation of the world, sense of human
existence, relationship of god and the person, but also offers the
ethical concept, develops rules of behavior of people. The religion a
long time dominated in the history of culture, and during this time
created a set of cultural and material values. The identity of Kazakh
culture can be defined as a Cultural identity traditional ,national
identity and the identity values developed by Kazakh people in
process of cultural-historical development, promoting formation of
Kazakh culture identity on public consciousness. Identity is the
historical process but always the tradition exists in it as a component
of stability, as a component of self that what this identity formed .