Abstract: This paper describes the experimental efficiency of a
compact organic Rankine cycle (ORC) system with a compact
rotary-vane-type expander. The compact ORC system can be used for
power generation from low-temperature heat sources such as waste
heat from various small-scale heat engines, fuel cells, electric devices,
and solar thermal energy. The purpose of this study is to develop an
ORC system with a low power output of less than 1 kW with a hot
temperature source ranging from 60°C to 100°C and a cold
temperature source ranging from 10°C to 30°C. The power output of
the system is rather less due to limited heat efficiency. Therefore, the
system should have an economically optimal efficiency. In order to
realize such a system, an efficient and low-cost expander is
indispensable. An experimental ORC system was developed using the
rotary-vane-type expander which is one of possible candidates of the
expander. The experimental results revealed the expander
performance for various rotation speeds, expander efficiencies, and
thermal efficiencies. Approximately 30 W of expander power output
with 48% expander efficiency and 4% thermal efficiency with a
temperature difference between the hot and cold sources of 80°C was
achieved.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: Only recently have water ethics received focused interest in the international water community. Because water is metabolically basic to life, an ethical dimension persists in every decision related to water. Water ethics at once express human society-s approach to water and act as guidelines for behaviour. Ideas around water are often implicit and embedded as assumptions. They can be entrenched in behaviour and difficult to contest because they are difficult to “see". By explicitly revealing the ethical ideas underlying water-related decisions, human society-s relationship with water, and with natural systems of which water is part, can be contested and shifted or be accepted with conscious intention by human society. In recent decades, improved understanding of water-s importance for ecosystem functioning and ecological services for human survival is moving us beyond this growth-driven, supplyfocused management paradigm. Environmental ethics challenge this paradigm by extending the ethical sphere to the environment and thus water or water Resources management per se. An ethical approach is a legitimate, important, and often ignored approach to effect change in environmental decision making. This qualitative research explores principles of water ethics and examines the underlying ethical precepts of selected water policy examples. The constructed water ethic principles act as a set of criteria against which a policy comparison can be established. This study shows that water Resources management is a progressive issue by embracing full public participation and a new planning model, and knowledgegeneration initiatives.
Abstract: Due to today-s turbulent environment, manufacturing resources, particularly in assembly, must be reconfigured frequently. These reconfigurations are caused by various, partly cyclic, influencing factors. Hence, it is important to evaluate the innovation ability - the capability of resources to implement innovations quickly and efficiently without large expense - of manufacturing resources. For this purpose, a new methodology is presented in this article. Within the methodology, design structure matrices and graph theory are used. The results of the methodology include different indices to evaluate the innovation ability of the manufacturing resources. Due to the cyclicity of the influencing factors, the methodology can be used to synchronize the realization of adaptations.
Abstract: The remote diagnosis and remote medical smoked to
part. In China, in accordance with the requirements of different
applications of remote diagnosis and Relates to the technical
difference, which can be divided into special purpose remote diagnosis
and treatment system, the remote will Referral system, remote medical
consultation system, remote rehabilitation technology and remote
operation technology. In this article, will introduce China for the
special purpose of service remote diagnosis and treatment system and
technology, including: China disabled status and virtual reality
technology; China 's domestic family medical care system and China 's
current situation of the development of telemedicine.
Abstract: A cognitive collaborative reinforcement learning
algorithm (CCRL) that incorporates an advisor into the learning
process is developed to improve supervised learning. An autonomous
learner is enabled with a self awareness cognitive skill to decide
when to solicit instructions from the advisor. The learner can also
assess the value of advice, and accept or reject it. The method is
evaluated for robotic motion planning using simulation. Tests are
conducted for advisors with skill levels from expert to novice. The
CCRL algorithm and a combined method integrating its logic with
Clouse-s Introspection Approach, outperformed a base-line fully
autonomous learner, and demonstrated robust performance when
dealing with various advisor skill levels, learning to accept advice
received from an expert, while rejecting that of less skilled
collaborators. Although the CCRL algorithm is based on RL, it fits
other machine learning methods, since advisor-s actions are only
added to the outer layer.
Abstract: We focus on the excitation and propagation properties
of surface plasmon polariton (SPP). We have developed a SPP
excitation device in combination with a grating structures fabricated
by using the scanning probe lithography. Perturbation approach was
used to investigate the coupling properties of SPP with a spatial
harmonic wave supported by a metallic grating. A phase shift grating
SPP coupler has been fabricated and the optical property was
evaluated by the Fraunhofer diffraction formula. We have been
experimentally confirmed the induced stop band by diffraction
measurement. We have also observed the wavenumber shift of the
resonance condition of SPP owing to effect of a phase shift.
Abstract: The SOM has several beneficial features which make
it a useful method for data mining. One of the most important
features is the ability to preserve the topology in the projection.
There are several measures that can be used to quantify the goodness
of the map in order to obtain the optimal projection, including the
average quantization error and many topological errors. Many
researches have studied how the topology preservation should be
measured. One option consists of using the topographic error which
considers the ratio of data vectors for which the first and second best
BMUs are not adjacent. In this work we present a study of the
behaviour of the topographic error in different kinds of maps. We
have found that this error devaluates the rectangular maps and we
have studied the reasons why this happens. Finally, we suggest a new
topological error to improve the deficiency of the topographic error.
Abstract: IEEE 802.11e is the enhanced version of the IEEE
802.11 MAC dedicated to provide Quality of Service of wireless
network. It supports QoS by the service differentiation and
prioritization mechanism. Data traffic receives different priority
based on QoS requirements. Fundamentally, applications are divided
into four Access Categories (AC). Each AC has its own buffer queue
and behaves as an independent backoff entity. Every frame with a
specific priority of data traffic is assigned to one of these access
categories. IEEE 802.11e EDCA (Enhanced Distributed Channel
Access) is designed to enhance the IEEE 802.11 DCF (Distributed
Coordination Function) mechanisms by providing a distributed
access method that can support service differentiation among
different classes of traffic. Performance of IEEE 802.11e MAC layer
with different ACs is evaluated to understand the actual benefits
deriving from the MAC enhancements.
Abstract: The paper outlines the drivers behind the movement
from products to solutions in the Hi-Tech Business-to-Business
markets. The paper lists out the challenges in enabling the
transformation from products to solutions and also attempts to explore
strategic and operational recommendations based on the authors-
factual experiences with Japanese Hi-tech manufacturing
organizations. Organizations in the Hi-Tech Business-to-Business
markets are increasingly being compelled to move to a solutions model
from the conventional products model. Despite the added complexity
of solutions, successful technology commercialization can be achieved
by making prudent choices in defining a relevant solutions model, by
backing the solution model through appropriate organizational design,
and by overhauling the new product development process and
supporting infrastructure.
Abstract: This paper tests the level of market integration between Malaysia and Singapore stock markets with the world market. Kalman Filter (KF) methodology is used on the International Capital Asset Pricing Model (ICAPM) and the pricing errors estimated within the framework of ICAPM are used as a measure of market integration or segmentation. The advantage of the KF technique is that it allows for time-varying coefficients in estimating ICAPM and hence able to capture the varying degree of market integration. Empirical results show clear evidence of varying degree of market integration for both case of Malaysia and Singapore. Furthermore, the results show that the changes in the level of market integration are found to coincide with certain economic events that have taken placed. The findings certainly provide evidence on the practicability of the KF technique to estimate stock markets integration. In the comparison between Malaysia and Singapore stock market, the result shows that the trends of the market integration indices for Malaysia and Singapore look similar through time but the magnitude is notably different with the Malaysia stock market showing greater degree of market integration. Finally, significant evidence of varying degree of market integration shows the inappropriate use of OLS in estimating the level of market integration.
Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: This paper makes an attempt to solve the problem of
searching and retrieving of similar MRI photos via Internet services
using morphological features which are sourced via the original
image. This study is aiming to be considered as an additional tool of
searching and retrieve methods. Until now the main way of the
searching mechanism is based on the syntactic way using keywords.
The technique it proposes aims to serve the new requirements of
libraries. One of these is the development of computational tools for
the control and preservation of the intellectual property of digital
objects, and especially of digital images. For this purpose, this paper
proposes the use of a serial number extracted by using a previously
tested semantic properties method. This method, with its center being
the multi-layers of a set of arithmetic points, assures the following
two properties: the uniqueness of the final extracted number and the
semantic dependence of this number on the image used as the
method-s input. The major advantage of this method is that it can
control the authentication of a published image or its partial
modification to a reliable degree. Also, it acquires the better of the
known Hash functions that the digital signature schemes use and
produces alphanumeric strings for cases of authentication checking,
and the degree of similarity between an unknown image and an
original image.
Abstract: We introduce and study the class of weak almost Dunford-Pettis operators. As an application, we characterize Banach lattices with the weak Dunford-Pettis property. Also, we establish some sufficient conditions for which each weak almost Dunford-Pettis operator is weak Dunford-Pettis. Finally, we derive some interesting results.
Abstract: The complexity of lignocellulosic biomass requires
a pretreatment step to improve the yield of fermentable sugars. The
efficient pretreatment of corn cobs using microwave and potassium
hydroxide and enzymatic hydrolysis was investigated. The
objective of this work was to characterize the optimal condition of
pretreatment of corn cobs using microwave and potassium
hydroxide enhance enzymatic hydrolysis. Corn cobs were
submerged in different potassium hydroxide concentration at varies
temperature and resident time. The pretreated corn cobs were
hydrolyzed to produce the reducing sugar for analysis. The
morphology and microstructure of samples were investigated by
Thermal gravimetric analysis (TGA, scanning electron microscope
(SEM), X-ray diffraction (XRD). The results showed that lignin
and hemicellulose were removed by microwave/potassium
hydroxide pretreatment. The crystallinity of the pretreated corn
cobs was higher than the untreated. This method was compared
with autoclave and conventional heating method. The results
indicated that microwave-alkali treatment was an efficient way to
improve the enzymatic hydrolysis rate by increasing its
accessibility hydrolysis enzymes.
Abstract: The paper examines the performance of bit-interleaved parity (BIP) methods in error rate monitoring, and in declaration and clearing of alarms in those transport networks that employ automatic protection switching (APS). The BIP-based error rate monitoring is attractive for its simplicity and ease of implementation. The BIP-based results are compared with exact results and are found to declare the alarms too late, and to clear the alarms too early. It is concluded that the standards development and systems implementation should take into account the fact of early clearing and late declaration of alarms. The window parameters defining the detection and clearing thresholds should be set so as to build sufficient hysteresis into the system to ensure that BIP-based implementations yield acceptable performance results.
Abstract: In recent years a number of applications with multirobot
systems (MRS) is growing in various areas. But their design
is in practice often difficult and algorithms are proposed for the
theoretical background and do not consider errors and noise in real
conditions, so they are not usable in real environment. These errors
are visible also in task of target localization enough, when robots
try to find and estimate the position of the target by the sensors.
Localization of target is possible also with one robot but as it was
examined target finding and localization with group of mobile robots
can estimate the target position more accurately and faster. The
accuracy of target position estimation is made by cooperation of
MRS and particle filtering. Advantage of usage the MRS with particle
filtering was tested on task of fixed target localization by group of
mobile robots.
Abstract: In this paper, an inventory model with finite and
constant replenishment rate, price dependant demand rate, time
value of money and inflation, finite time horizon, lead time and
exponential deterioration rate and with the objective of maximizing
the present worth of the total system profit is developed. Using a
dynamic programming based solution algorithm, the optimal
sequence of the cycles can be found and also different optimal
selling prices, optimal order quantities and optimal maximum
inventories can be obtained for the cycles with unequal lengths,
which have never been done before for this model. Also, a
numerical example is used to show accuracy of the solution
procedure.
Abstract: School homework has been synonymous with students- life in Chinese national type primary schools in Malaysia. Although many reports in the press claimed that students were burdened with too much of it, homework continues to be a common practice in national type schools that is believed to contribute to academic achievement. This study is conducted to identify the relationship between the burden of school homework and academic achievement among pupils in Chinese National Type Primary School in the state of Perak, Malaysia. A total of 284 students (142 from urban and 142 from rural) respectively were chosen as participants in this study. Variables of gender and location (urban/rural areas) has shown significant difference in student academic achievement. Female Chinese student from rural areas showed a higher mean score than males from urban area. Therefore, the Chinese language teachers should give appropriate and relevant homework to primary school students to achieve good academic performance.
Abstract: As the data-driven economy is growing faster than
ever and the demand for energy is being spurred, we are facing
unprecedented challenges of improving energy efficiency in data
centers. Effectively maximizing energy efficiency or minimising the
cooling energy demand is becoming pervasive for data centers. This
paper investigates overall energy consumption and the energy
efficiency of cooling system for a data center in Finland as a case
study. The power, cooling and energy consumption characteristics
and operation condition of facilities are examined and analysed.
Potential energy and cooling saving opportunities are identified and
further suggestions for improving the performance of cooling system
are put forward. Results are presented as a comprehensive evaluation
of both the energy performance and good practices of energy
efficient cooling operations for the data center. Utilization of an
energy recovery concept for cooling system is proposed. The
conclusion we can draw is that even though the analysed data center
demonstrated relatively high energy efficiency, based on its power
usage effectiveness value, there is still a significant potential for
energy saving from its cooling systems.