Abstract: The compressive strength development through
polymerization process of alkaline solution and fly ash blended with Microwave Incinerated Rice Husk Ash (MIRHA) is described in this
paper. Three curing conditions, which are hot gunny curing, ambient
curing, and external humidity curing are investigated to obtain the suitable curing condition for cast in situ provision. Fly ash was
blended with MIRHA at 3%, 5%, and 7% to identify the effect of blended mixes to the compressive strength and microstructure
properties of geopolymer concrete. Compressive strength results
indicated an improvement in the strength development with external humidity curing concrete samples compared to hot gunny curing and
ambient curing. Blended mixes also presented better performance
than control mixes. Improvement of interfacial transition zone (ITZ)
and micro structure in external humidity concrete samples were also
identified compared to hot gunny and ambient curing.
Abstract: Low-density parity-check (LDPC) codes have been shown to deliver capacity approaching performance; however, problematic graphical structures (e.g. trapping sets) in the Tanner graph of some LDPC codes can cause high error floors in bit-error-ratio (BER) performance under conventional sum-product algorithm (SPA). This paper presents a serial concatenation scheme to avoid the trapping sets and to lower the error floors of LDPC code. The outer code in the proposed concatenation is the LDPC, and the inner code is a high rate array code. This approach applies an interactive hybrid process between the BCJR decoding for the array code and the SPA for the LDPC code together with bit-pinning and bit-flipping techniques. Margulis code of size (2640, 1320) has been used for the simulation and it has been shown that the proposed concatenation and decoding scheme can considerably improve the error floor performance with minimal rate loss.
Abstract: Studies have shown that the SnAgCu solder family has been widely used as a replacement for conventional Sn-Pb solders. An attractive approach is by introducing alloying additives (rare earth elements (RE), Zn, Co, Fe, Ni, Sb) into the SnAgCu solder, which helps in refining the microstructure also improving the mechanical and wetting properties of the solder. The present work focuses on the effect of additions of 0.5% Ce and Fe into Sn-3.0Ag-0.5Cu solder, in attempt to reduce the intermetallic compound (IMC) growth and reflow properties of the solder on Cu and Ni (P) surface finish, as well as effects thermal aging on the formation of intermetallic compound (IMC) on different surface finish. Excessive intermetallic compound growth may effect the interface and solder joint due to the brittle nature of the intermetallic compounds. Thus, by introducing alloying elements, IMC layer thickness can be decrease, resulting in better joint and solder reliability.
Abstract: The paper shows some ability to manage two-phase
flows arising from the use of unsteady effects. In one case, we
consider the condition of fragmentation of the interface between the
two components leads to the intensification of mixing. The problem
is solved when the temporal and linear scale are small for the
appearance of the developed mixing layer. Showing that exist such
conditions for unsteady flow velocity at the surface of the channel,
which will lead to the creation and fragmentation of vortices at Re
numbers of order unity. Also showing that the Re is not a criterion of
similarity for this type of flows, but we can introduce a criterion that
depends on both the Re, and the frequency splitting of the vortices. It
turned out that feature of this situation is that streamlines behave
stable, and if we analyze the behavior of the interface between the
components it satisfies all the properties of unstable flows. The other
problem we consider the behavior of solid impurities in the extensive
system of channels. Simulated unsteady periodic flow modeled
breaths. Consider the behavior of the particles along the trajectories.
It is shown that, depending on the mass and diameter of the particles,
they can be collected in a caustic on the channel walls, stop in a
certain place or fly back. Of interest is the distribution of particle
velocity in frequency. It turned out that by choosing a behavior of the
velocity field of the carrier gas can affect the trajectory of individual
particles including force them to fly back.
Abstract: The objective of this research was to study the factors
related to the satisfaction of consumers who purchased a Toyota
SUV Fortuner. This paper was a survey data which collected 400
samples from 65 car dealerships. The survey was conducted mainly
in Bangkok, Thailand. The statistics utilized in this paper included
percentage, mean, standard deviation and Pearson Product-Moment.
The findings revealed that the majority of respondent were male with
an undergraduate degree, married and live together. The average
income of the respondents was between 20,001 - 30,000 baht. Most
of them worked for private companies. Most of them had a family
with the average of 4 members. The hypotheses testing revealed that
the factors of marketing mix in terms of product (ability, gas
mileage, and safety) were related to overall satisfaction at the
medium level. However, the findings also revealed that the factors of
marketing mix in terms of product (image), price, and promotion, and
service center were related to the overall satisfaction at the low level.
Abstract: The recognition of human faces, especially those with
different orientations is a challenging and important problem in image
analysis and classification. This paper proposes an effective scheme
for rotation invariant face recognition using Log-Polar Transform and
Discrete Cosine Transform combined features. The rotation invariant
feature extraction for a given face image involves applying the logpolar
transform to eliminate the rotation effect and to produce a row
shifted log-polar image. The discrete cosine transform is then applied
to eliminate the row shift effect and to generate the low-dimensional
feature vector. A PSO-based feature selection algorithm is utilized to
search the feature vector space for the optimal feature subset.
Evolution is driven by a fitness function defined in terms of
maximizing the between-class separation (scatter index).
Experimental results, based on the ORL face database using testing
data sets for images with different orientations; show that the
proposed system outperforms other face recognition methods. The
overall recognition rate for the rotated test images being 97%,
demonstrating that the extracted feature vector is an effective rotation
invariant feature set with minimal set of selected features.
Abstract: Digital watermarking is one of the techniques for
copyright protection. In this paper, a normalization-based robust
image watermarking scheme which encompasses singular value
decomposition (SVD) and discrete cosine transform (DCT)
techniques is proposed. For the proposed scheme, the host image is
first normalized to a standard form and divided into non-overlapping
image blocks. SVD is applied to each block. By concatenating the
first singular values (SV) of adjacent blocks of the normalized image,
a SV block is obtained. DCT is then carried out on the SV blocks to
produce SVD-DCT blocks. A watermark bit is embedded in the highfrequency
band of a SVD-DCT block by imposing a particular
relationship between two pseudo-randomly selected DCT
coefficients. An adaptive frequency mask is used to adjust local
watermark embedding strength. Watermark extraction involves
mainly the inverse process. The watermark extracting method is blind
and efficient. Experimental results show that the quality degradation
of watermarked image caused by the embedded watermark is visually
transparent. Results also show that the proposed scheme is robust
against various image processing operations and geometric attacks.
Abstract: Pineapples can be classified using an index with seven
levels of maturity based on the green and yellow color of the skin. As
the pineapple ripens, the skin will change from pale green to a golden
or yellowish color. The issues that occur in agriculture nowadays are
to do with farmers being unable to distinguish between the indexes of
pineapple maturity correctly and effectively. There are several
reasons for why farmers cannot properly follow the guideline provide
by Federal Agriculture Marketing Authority (FAMA) and one of
reason is that due to manual inspection done by experts, there are no
specific and universal guidelines to be adopted by farmers due to the
different points of view of the experts when sorting the pineapples
based on their knowledge and experience. Therefore, an automatic
system will help farmers to identify pineapple maturity effectively
and will become a universal indicator to farmers.
Abstract: User-Centered Design (UCD), Usability Engineering (UE) and Participatory Design (PD) are the common Human- Computer Interaction (HCI) approaches that are practiced in the software development process, focusing towards issues and matters concerning user involvement. It overlooks the organizational perspective of HCI integration within the software development organization. The Management Information Systems (MIS) perspective of HCI takes a managerial and organizational context to view the effectiveness of integrating HCI in the software development process. The Human-Centered Design (HCD) which encompasses all of the human aspects including aesthetic and ergonomic, is claimed as to provide a better approach in strengthening the HCI approaches to strengthen the software development process. In determining the effectiveness of HCD in the software development process, this paper presents the findings of a content analysis of HCI approaches by viewing those approaches as a technology which integrates user requirements, ranging from the top management to other stake holder in the software development process. The findings obtained show that HCD approach is a technology that emphasizes on human, tools and knowledge in strengthening the HCI approaches to strengthen the software development process in the quest to produce a sustainable, usable and useful software product.
Abstract: In this paper, algorithm estimating the blood pressure
was proposed using the pulse transit time (PTT) as a more convenient
method of measuring the blood pressure. After measuring ECG and
pressure pulse, and photoplethysmography, the PTT was calculated
from the acquired signals. Thereafter, the system to indirectly measure
the systolic pressure and the diastolic pressure was composed using
the statistic method. In comparison between the blood pressure
indirectly measured by proposed algorithm estimating the blood
pressure and real blood pressure measured by conventional
sphygmomanometer, the systolic pressure indicates the mean error of
±3.24mmHg and the standard deviation of 2.53mmHg, while the
diastolic pressure indicates the satisfactory result, that is, the mean
error of ±1.80mmHg and the standard deviation of 1.39mmHg. These
results are satisfied with the regulation of ANSI/AAMI for
certification of sphygmomanometer that real measurement error value
should be within the mean error of ±5mmHg and the standard
deviation of 8mmHg. These results are suggest the possibility of
applying to portable and long time blood pressure monitoring system
hereafter.
Abstract: Ozone (O3) is considered as one of the most
phytotoxic pollutants with deleterious effects on living and non living
components of Ecosystems. It reduces growth and yield of many
crops as well as alters the physiology and crop quality. The present
study described series of experiments to investigate the effects of
ambient O3 at different locations with different ambient levels of O3
depending on proximity to pollutant source and ranged between 17
ppb/h in control experiment to 112 ppb/h in industrial area
respectively. The ambient levels in other three locations (King Saud
University botanical garden, King Fahd Rd, and Almanakh Garden)
were 61,61,77 ppb/h respectively. Tow legume crops species (vicia
vaba L ; and Pisum sativum) differ in their phenology and sensitivity
were used. The results showed a significant negative effect to ozone
on morphology, number of injured leaves, growth and productivity
with a difference in the degree of response depending on the plant
type. Visia Faba showed sensitivity to ozone to number and leaf area
and the degree of injury leaves 3, pisum sativum show higher
sensitivity for the gas for degree of injury 1,The relative growth rate
and seed weight, it turns out there is no significant difference
between the two plants in plant height and number of seeds.
Abstract: In many applications, it is a priori known that the
target function should satisfy certain constraints imposed by, for
example, economic theory or a human-decision maker. Here we
consider partially monotone problems, where the target variable
depends monotonically on some of the predictor variables but not all.
We propose an approach to build partially monotone models based
on the convolution of monotone neural networks and kernel
functions. The results from simulations and a real case study on
house pricing show that our approach has significantly better
performance than partially monotone linear models. Furthermore, the
incorporation of partial monotonicity constraints not only leads to
models that are in accordance with the decision maker's expertise,
but also reduces considerably the model variance in comparison to
standard neural networks with weight decay.
Abstract: Recently, the RFID (Radio Frequency
Identification) technology attracts the world market attention as
essential technology for ubiquitous environment. The RFID
market has focused on transponders and reader development.
But that concern has shifted to RFID software like as
high-valued e-business applications, RFID middleware and
related development tools. However, due to the high sensitivity
of data and service transaction within the RFID network,
security consideration must be addressed. In order to guarantee
trusted e-business based on RFID technology, we propose a
security enhanced RFID middleware system. Our proposal is
compliant with EPCglobal ALE (Application Level Events),
which is standard interface for middleware and its clients. We
show how to provide strengthened security and trust by
protecting transported data between middleware and its client,
and stored data in middleware. Moreover, we achieve the
identification and service access control against illegal service
abuse. Our system enables secure RFID middleware service
and trusted e-business service.
Abstract: The problem of frequent itemset mining is considered in this paper. One new technique proposed to generate frequent patterns in large databases without time-consuming candidate generation. This technique is based on focusing on transaction instead of concentrating on itemset. This algorithm based on take intersection between one transaction and others transaction and the maximum shared items between transactions computed instead of creating itemset and computing their frequency. With applying real life transactions and some consumption is taken from real life data, the significant efficiency acquire from databases in generation association rules mining.
Abstract: As embedded and portable systems were emerged power consumption of circuits had been major challenge. On the other hand latency as determines frequency of circuits is also vital task. Therefore, trade off between both of them will be desirable. Modulo 2n+1 adders are important part of the residue number system (RNS) based arithmetic units with the interesting moduli set (2n-1,2n, 2n+1). In this manuscript we have introduced novel binary representation to the design of modulo 2n+1 adder. VLSI realization of proposed architecture under 180 nm full static CMOS technology reveals its superiority in terms of area, power consumption and power-delay product (PDP) against several peer existing structures.
Abstract: In this paper a new approach to face recognition is presented that achieves double dimension reduction making the system computationally efficient with better recognition results. In pattern recognition techniques, discriminative information of image increases with increase in resolution to a certain extent, consequently face recognition results improve with increase in face image resolution and levels off when arriving at a certain resolution level. In the proposed model of face recognition, first image decimation algorithm is applied on face image for dimension reduction to a certain resolution level which provides best recognition results. Due to better computational speed and feature extraction potential of Discrete Cosine Transform (DCT) it is applied on face image. A subset of coefficients of DCT from low to mid frequencies that represent the face adequately and provides best recognition results is retained. A trade of between decimation factor, number of DCT coefficients retained and recognition rate with minimum computation is obtained. Preprocessing of the image is carried out to increase its robustness against variations in poses and illumination level. This new model has been tested on different databases which include ORL database, Yale database and a color database. The proposed technique has performed much better compared to other techniques. The significance of the model is two fold: (1) dimension reduction up to an effective and suitable face image resolution (2) appropriate DCT coefficients are retained to achieve best recognition results with varying image poses, intensity and illumination level.
Abstract: Previous research has demonstrated that negative
attitudes towards people with physical disabilities and obesity are
predicted by a component of perceived vulnerability to disease; germ
aversion. These findings have been suggested as illustrations of an
evolved but over-active mechanism which promotes the avoidance of
pathogen-carrying individuals. To date, this interpretation of attitude
formation has not been explored with regard to people with
intellectual disability, and no attempts have been made to examine
possible mediating factors. This study examined attitudes in 333
adults and demonstrated that the moderate positive relationship
between germ aversion and negative attitudes toward people with
intellectual disability is fully mediated by social dominance
orientation, a general preference for hierarchies and inequalities
among social groups. These findings have implications for the
design of programs which attempt to promote community acceptance
and inclusion of people with disabilities.
Abstract: Bond graph models of an electrical transformer including
the nonlinear saturation are presented. The transformer
using electrical and magnetic circuits are modelled. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two windings using the properties of a bond graph. The
equivalence between electrical and magnetic variables is given.
The modelling and analysis using this methodology to three phase
power transformers can be extended.
Abstract: Even though most researchers would agree that in
symbiotic relationships, like the one between parent and child,
influences become reciprocal over time, empirical evidence
supporting this claim is limited. The aim of the current study was to
develop and test a model describing the reciprocal influence between
characteristics of the parent-child relationship, such as closeness and
conflict, and the child-s bullying and victimization experiences at
school. The study used data from the longitudinal Study of Early
Child-Care, conducted by the National Institute of Child Health and
Human Development. The participants were dyads of early
adolescents (5th and 6th graders during the two data collection waves)
and their mothers (N=1364). Supporting our hypothesis, the findings
suggested a reciprocal association between bullying and positive
parenting, although this association was only significant for boys.
Victimization and positive parenting were not significantly
interrelated.
Abstract: Ferroresonance is an electrical phenomenon in
nonlinear character, which frequently occurs in power system due to
transmission line faults and single or more-phase switching on the
lines as well as usage of the saturable transformers. In this study, the
ferroresonance phenomena are investigated under the modeling of the
West Anatolian Electric Power Network of 380 kV in Turkey. The
ferroresonance event is observed as a result of removing the loads at
the end of the lines. In this sense, two different cases are considered.
At first, the switching is applied at 2nd second and the ferroresonance
affects are observed between 2nd and 4th seconds in the voltage
variations of the phase-R. Hence the ferroresonance and nonferroresonance
parts of the overall data are compared with each
others using the Fourier transform techniques to show the
ferroresonance affects.