Abstract: In this paper, the babbitting of a bearing in boiler feed pump of an electromotor has been studied. These bearings have an important role in reducing the shut down times in the pumps, compressors and turbines. The most conventional method in babbitting is casting as a melting method. The comparison between thermal spray and casting methods in babbitting shows that the thermal spraying babbitt layer has better performance and tribological behavior. The metallurgical and tribological analysis such as SEM, EDS and wet chemical analysis has been made in the Babbitt alloys and worn surfaces. Two type of babbitt materials: tinbase and lead-base babbitt was used. The benefits of thermally sprayed babbitt layers are completely clear especially in large bearings.
Abstract: In this paper, LDPC Codes based on defected fullerene
graphs have been generated. And it is found that the codes generated
are fast in encoding and better in terms of error performance on
AWGN Channel.
Abstract: A lightpipe is an about 99 percent specular reflective
mirror pipe or duct that is used for the transmission of the daylight
from the outside into a building. The lightpipes are usually used in
the daylighting buildings, in the residential, industrial and
commercial sectors. This paper is about the performances of a
lightpipe installed in a laboratory (3 m x 2.6 m x 3 m) without
windows. The aim is to analyse the luminous intensity distribution
for several sky/sun conditions. The lightpipe was monitored during
the year 2006. The lightpipe is 1 m long and the diameter of the top
collector and of the internal diffuser device is 0.25 m. In the
laboratory there are seven illuminance sensors: one external is
located on the roof of the laboratory and six internal sensors are
connected to a data acquisition system. The internal sensors are
positioned under the internal diffusive device at an height of 0.85 m
from the floor to simulate a working plane. The numerical data are
obtained through a simulation software. This paper shows the
comparison between the experimental and numerical results
concerning the behavior of the lightpipe.
Abstract: Fuzzy Cognitive Maps (FCMs) have successfully
been applied in numerous domains to show relations between
essential components. In some FCM, there are more nodes, which
related to each other and more nodes means more complex in system
behaviors and analysis. In this paper, a novel learning method used to
construct FCMs based on historical data and by using data mining
and DEMATEL method, a new method defined to reduce nodes
number. This method cluster nodes in FCM based on their cause and
effect behaviors.
Abstract: Service discovery is a very important component of Service Oriented Architectures (SOA). This paper presents two alternative approaches to customise the query results of private service registry such as Universal Description, Discovery and Integration (UDDI). The customisation is performed based on some pre-defined and/or real-time changing parameters. This work identifies the requirements, designs and additional mechanisms that must be applied to UDDI in order to support this customisation capability. We also detail the implements of the approaches and examine its performance and scalability. Based on our experimental results, we conclude that both approaches can be used to customise registry query results, but by storing personalization parameters in external resource will yield better performance and but less scalable when size of query results increases. We believe these approaches when combined with semantics enabled service registry will enhance the service discovery methods within a private UDDI registry environment.
Abstract: power-line networks are promise infrastructure for
broadband services provision to end users. However, the network
performance is affected by stochastic channel changing which is due
to load impedances, number of branches and branched line lengths. It
has been proposed that multi-carrier modulations techniques such as
orthogonal frequency division multiplexing (OFDM), Multi-Carrier
Spread Spectrum (MC-SS), wavelet OFDM can be used in such
environment. This paper investigates the performance of different
indoor topologies of power-line networks that uses MC-SS
modulation scheme.It is observed that when a branch is added in the
link between sending and receiving end of an indoor channel an
average of 2.5dB power loss is found. In additional, when the branch
is added at a node an average of 1dB power loss is found.
Additionally when the terminal impedances of the branch change
from line characteristic impedance to impedance either higher or
lower values the channel performances were tremendously improved.
For example changing terminal load from characteristic impedance
(85 .) to 5 . the signal to noise ratio (SNR) required to attain the
same performances were decreased from 37dB to 24dB respectively.
Also, changing the terminal load from channel characteristic
impedance (85 .) to very higher impedance (1600 .) the SNR
required to maintain the same performances were decreased from
37dB to 23dB. The result concludes that MC-SS performs better
compared with OFDM techniques in all aspects and especially when
the channel is terminated in either higher or lower impedances.
Abstract: Most of the biclustering/projected clustering algorithms are based either on the Euclidean distance or correlation coefficient which capture only linear relationships. However, in many applications, like gene expression data and word-document data, non linear relationships may exist between the objects. Mutual Information between two variables provides a more general criterion to investigate dependencies amongst variables. In this paper, we improve upon our previous algorithm that uses mutual information for biclustering in terms of computation time and also the type of clusters identified. The algorithm is able to find biclusters with mixed relationships and is faster than the previous one. To the best of our knowledge, none of the other existing algorithms for biclustering have used mutual information as a similarity measure. We present the experimental results on synthetic data as well as on the yeast expression data. Biclusters on the yeast data were found to be biologically and statistically significant using GO Tool Box and FuncAssociate.
Abstract: This study focused on arsenate removal by nano
zero-valent iron (NZVI) in the gas-bubbled aqueous solution. It
appears that solution acidified by H2SO4 is far more favorable than by
CO2-bubbled acidification. In addition, as dissolved oxygen was
stripped out of solution by N2 gas bubbling, the arsenate removal
dropped significantly. To take advantages of common practice of
carbonation and oxic condition, pretreatment of CO2 and air bubbling
in sequence are recommended for a better removal of arsenate.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: In the past 20 years the economy of the Czech
Republic has experienced substantial changes. In the 1990s the
development was affected by the transformation which sought to
establish the right conditions for privatization and creation of
elementary market relations. In the last decade the characteristic
elements such as private ownership and corresponding institutional
framework have been strengthened. This development was marked by
the accession of the Czech Republic to the EU. The Czech Republic
is striving to reduce the difference between its level of economic
development and the quality of institutional framework in
comparison with other developed countries. The process of finding
the adequate solutions has been hampered by the negative impact of
the world financial crisis on the Czech Republic and the standard of
living of its inhabitants. This contribution seeks to address the
question of whether and to which extent the economic development
of the transitive Czech economy is affected by the change in
behaviour of households and their tendency to consumption, i.e. in
the sense of reduction or increase in demand for goods and services.
It aims to verify whether the increasing trend of household
indebtedness and decreasing trend of saving pose a significant risk in
the Czech Republic. At a general level the analysis aims to contribute
to finding an answer to the question of whether the debt increase of
Czech households is connected to the risk of "eating through" the
borrowed money and whether Czech households risk falling into a
debt trap. In addition to household indebtedness risks in the Czech
Republic the analysis will focus on identification of specifics of the
transformation phase of the Czech economy in comparison with the
EU countries, or selected OECD countries.
Abstract: The number of the companies accepting RFID in Korea
has been increased continuously due to the domestic development of
information technology. The acceptance of RFID by companies in
Korea enabled them to do business with many global enterprises in a
much more efficient and effective way. According to a survey[33,
p76], many companies in Korea have used RFID for inventory or
distribution manages. But, the use of RFID in the companies in Korea
is in the early stages and its potential value hasn-t fully been realized
yet. At this time, it would be very important to investigate the factors
that affect RFID acceptance. For this study, many previous studies
were referenced and some RFID experts were interviewed. Through
the pilot test, four factors were selected - Security Trust, Employee
Knowledge, Partner Influence, Service Provider Trust - affecting
RFID acceptance and an extended technology acceptance
model(e-TAM) was presented with those factors. The proposed model
was empirically tested using data collected from employees in
companies or public enterprises. In order to analyze some
relationships between exogenous variables and four variables in TAM,
structural equation modeling(SEM) was developed and SPSS12.0 and
AMOS 7.0 were used for analyses. The results are summarized as
follows: 1) security trust perceived by employees positively
influences on perceived usefulness and perceived ease of use; 2)
employee-s knowledge on RFID positively influences on only
perceived ease of use; 3) a partner-s influence for RFID acceptance
positively influences on only perceived usefulness; 4) service provider
trust very positively influences on perceived usefulness and perceived
ease of use 5) the relationships between TAM variables are the same as
the previous studies.
Abstract: In this contribution, a way to enhance the performance of the classic Genetic Algorithm is proposed. The idea of restarting a Genetic Algorithm is applied in order to obtain better knowledge of the solution space of the problem. A new operator of 'insertion' is introduced so as to exploit (utilize) the information that has already been collected before the restarting procedure. Finally, numerical experiments comparing the performance of the classic Genetic Algorithm and the Genetic Algorithm with restartings, for some well known test functions, are given.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: The aim of this study was to examine the dynamics of functional composition of a non flooded Amazonian forest in response to drought stress in terms of diameter growth, recruitment and mortality. The survey was carried out in the continuous forest of the Biological dynamics of forest fragments project 90 km outside the city of Manaus, state of Amazonas Brazil. All stems >10 cm dbh where identified to species level and monitored in 18 one hectare permanent sample plots from 1981 to 2004.For statistical analysis all species where aggregated in three ecological guilds. Two distinct drought events occurred in 1983 and 1997. Results showed that more early successional species performed better than later successional ones. Response was significant for both events but for the 1997 event this was more pronounced possibly because of the fact that the event was in the middle of the dry rather than the wet period as was the 1983 one.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: Discrimination between different classes of environmental
sounds is the goal of our work. The use of a sound recognition
system can offer concrete potentialities for surveillance and
security applications. The first paper contribution to this research
field is represented by a thorough investigation of the applicability
of state-of-the-art audio features in the domain of environmental
sound recognition. Additionally, a set of novel features obtained by
combining the basic parameters is introduced. The quality of the
features investigated is evaluated by a HMM-based classifier to which
a great interest was done. In fact, we propose to use a Multi-Style
training system based on HMMs: one recognizer is trained on a
database including different levels of background noises and is used
as a universal recognizer for every environment. In order to enhance
the system robustness by reducing the environmental variability, we
explore different adaptation algorithms including Maximum Likelihood
Linear Regression (MLLR), Maximum A Posteriori (MAP)
and the MAP/MLLR algorithm that combines MAP and MLLR.
Experimental evaluation shows that a rather good recognition rate
can be reached, even under important noise degradation conditions
when the system is fed by the convenient set of features.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
relationship between the minimum direct and indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of direct and indirect jerks are found using the dynamic optimization
methods together with the numerical approximation. This is to allow
us to simulate and compare visually and statistically the time history
of control inputs employed by minimum direct and indirect jerk
designs. By considering minimum indirect jerk problem, the
numerical solution becomes much easier and yields to the similar
results as minimum direct jerk problem.
Abstract: In recent years, fast neural networks for object/face detection have been introduced based on cross correlation in the frequency domain between the input matrix and the hidden weights of neural networks. In our previous papers [3,4], fast neural networks for certain code detection was introduced. It was proved in [10] that for fast neural networks to give the same correct results as conventional neural networks, both the weights of neural networks and the input matrix must be symmetric. This condition made those fast neural networks slower than conventional neural networks. Another symmetric form for the input matrix was introduced in [1-9] to speed up the operation of these fast neural networks. Here, corrections for the cross correlation equations (given in [13,15,16]) to compensate for the symmetry condition are presented. After these corrections, it is proved mathematically that the number of computation steps required for fast neural networks is less than that needed by classical neural networks. Furthermore, there is no need for converting the input data into symmetric form. Moreover, such new idea is applied to increase the speed of neural networks in case of processing complex values. Simulation results after these corrections using MATLAB confirm the theoretical computations.
Abstract: Mankind has entered into an extremely complex and
controversial stage of its development: the world is simultaneously
organized and chaoticized, globalized and localized, combined and
split. Analysts point out that globalization as a process of
strengthening economic, cultural, financial and other ties of states
cause many problems. In the economic sphere, it creates the danger
of growing gap between the states, in the sphere of politics it leads to
the weakening of political power and influence of nation-states.
Abstract: Currently is characterized production engineering
together with the integration of industrial automation and robotics
such very quick view of to manufacture the products. The production
range is continuously changing, expanding and producers have to be
flexible in this regard. It means that need to offer production
possibilities, which can respond to the quick change. Engineering
product development is focused on supporting CAD software, such
systems are mainly used for product design. That manufacturers are
competitive, it should be kept procured machines made available
capable of responding to output flexibility. In response to that
problem is the development of flexible manufacturing systems,
consisting of various automated systems. The integration of flexible
manufacturing systems and subunits together with product design and
of engineering is a possible solution for this issue. Integration is
possible through the implementation of CIM systems. Such a solution
and finding a hyphen between CAD and procurement system ICIM
3000 from Festo Co. is engaged in the research project and this
contribution. This can be designed the products in CAD systems and
watch the manufacturing process from order to shipping by the
development of methods and processes of integration, This can be
modeled in CAD systems products and watch the manufacturing
process from order to shipping to develop methods and processes of
integration, which will improve support for product design
parameters by monitoring of the production process, by creating of
programs for production using the CAD and therefore accelerates the
a total of process from design to implementation.