Abstract: The study investigated efficiency cassava peel carbon
and Zinc Chloride activated cassava peel carbon at 1:3, 2:3 and 1:1
activation levels in the removal of nitrates from oxidized cassava
processing wastewater. Results showed that the CPC and CPAC were
effective in adsorption of nitrates. A summary of results from the
study revealed that CPAC at 1:3 exhibited the highest initial
decontamination (69.5% after 2 hrs) while CPAC at 1:1 activation
ratio showed a slower initial decontamination rate. The CPC &
CPAC exhibited Langmuir Rα values of 0.15, 0.11, 0.09, and 0.07 for
the 0:1, 1:3, 2:3 and 1:1 confirming its suitability as adsorption
material.
Abstract: The effects of wood ash from five common tropical
woods on the ignition point of four common tropical woods in
Nigeria were investigated. The ash and moisture contents of the wood
sawdust from Mahogany (Khaya ivorensis), Opepe (Sarcocephalus
latifolius), Abura (Mitragyna ciliata), Rubber (Heavea brasilensis)
and Poroporo (Sorghum bicolour) used, were determined using a
furnace (Vecstar furnaces, model ECF2, serial no. f3077) and oven
(Genlab laboratory oven, model MINO/040) respectively. The metal
contents of the five wood sawdust ash samples were determined
using a Perkin Elmer optima 3000 dv atomic absorption spectrometer
while the ignition points were determined using Vecstar furnaces
model ECF2. Poroporo had the highest ash content, 2.263g while
rubber had the least, 0.710g. The results for the moisture content
range from 2.971g to 0.903g. Magnesium metal had the highest
concentration of all the metals, in all the wood ash samples; with
mahogany ash having the highest concentration, 9.196ppm while
rubber ash had the least concentration of magnesium metal, 2.196
ppm. The ignition point results showed that the wood ashes from
mahogany and opepe increased the ignition points of the test wood
samples, Danta (Nesogordonia papaverifera), Ekpaya, Akomu
(Pycnanthus angolensis) and Oleku when coated on them while the
ashes from poroporo, rubber and abura decreased the ignition points
of the test wood samples when coated on them. However, Opepe saw
dust ash decreased the ignition point in one of the test wood samples,
suggesting that the metal content of the test wood sample was more
than that of the Opepe saw dust ash. Therefore, Mahogany and Opepe
saw dust ashes could be used in the surface treatment of wood to
enhance their fire resistance or retardancy. However, the caution to
be exercised in this application is that the metal content of the test
wood samples should be evaluated as well.
Abstract: Cholera is a disease that is predominately common in
developing countries due to poor sanitation and overcrowding
population. In this paper, a deterministic model for the dynamics of
cholera is developed and control measures such as health educational
message, therapeutic treatment, and vaccination are incorporated in
the model. The effective reproduction number is computed in terms
of the model parameters. The existence and stability of the
equilibrium states, disease free and endemic equilibrium states are
established and showed to be locally and globally asymptotically
stable when R0 < 1 and R0 > 1 respectively. The existence of
backward bifurcation of the model is investigated. Furthermore,
numerical simulation of the model developed is carried out to show
the impact of the control measures and the result indicates that
combined control measures will help to reduce the spread of cholera
in the population.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: The problem of degradation of agricultural residues
from palm oil industry is increasing due to its expansion.
Lignocelloulosic waste from these industry represent large amount of
unutilized resources, this is due to their high lignin content. Since
white rot fungi are capable of degrading lignin, its potential for the
degradation of lignocelloulosic waste from palm oil industry was
accessed. The lignocellluloses content was measured before and after
biodegradation and the rate of reduction was determined. From the
results of the biodegradation, it was observed that hemicellulose
reduces by 22.62%, cellulose by 20.97% and lignin by 10.65% from
the initials lignocelluloses contents. Thus, to improve the digestibility
of palm oil mesocarp fibre, treatment by white rot-fungi is
recommended.
Abstract: Carbon nanotubes (CNTs) are known for having high elastic properties with high surface area that promote them as good candidates for reinforcing polymeric matrices. In composite materials, CNTs lack chemical bonding with the surrounding matrix which decreases the possibility of better stress transfer between the components. In this work, a chemical treatment for activating the surface of the multi-wall carbon nanotubes (MWCNT) was applied and the effect of this functionalization on the elastic properties of the epoxy nanocomposites was studied. Functional amino-groups were added to the surface of the CNTs and it was evaluated to be about 34% of the total weight of the CNTs. Elastic modulus was found to increase by about 40% of the neat epoxy resin at CNTs’ weight fraction of 0.5%. The elastic modulus was found to decrease after reaching a certain concentration of CNTs which was found to be 1% wt. The scanning electron microscopic pictures showed the effect of the CNTs on the crack propagation through the sample by forming stress concentrated spots at the nanocomposite samples.
Abstract: Tannins are a unique category of plant phytochemicals
especially in terms of their vast potential health-benefiting properties.
Researchers have described the capacity of tannins to enhance
glucose uptake and inhibit adipogenesis, thus being potential drugs
for the treatment of non-insulin dependent diabetes mellitus. Thus,
the present research was conducted to find out tannin content of food
products. The percentage of tannin in various analyzed sources
ranged from 0.0 to 108.53%; highest in kathaa and lowest in ker and
mango bark. The percentage of tannins present in the plants,
however, varies. Numerous studies have confirmed that the naturally
occurring polyphenols are key factor for the beneficial effects of the
herbal medicines. Isolation and identification of active constituents
from plants, preparation of standardized dose & dosage regimen can
play a significant role in improving the hypoglycaemic action.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: We investigated ecotoxicity and performed experiment
for removing ZnO nanoparticles in water. Short term exposure of
hatching test using fertilized eggs (O. latipes) showed deformity in
5ppm of ZnO nanoparticles solution. And in 10ppm ZnO nanoparticles
solution delayed hatching was observed. Hereine, chemical
precipitation method was suggested for removing ZnO nanoparticles
in water. The precipitated ZnO nanoparticles showed the form of ZnS
after addition of Na2S, and the form of Zn3(PO4)2 for Na2HPO4. The
removal efficiency of ZnO nanoparticles in water was closed to 100%
for two cases. In ecotoxicity evaluation of as-precipitated ZnS and
Zn3(PO4)2, they did not cause any acute toxicity for D. magna. It is
noted that this precipitation treatment of ZnO is effective to reduce the
potential cytotoxicity.
Abstract: Biomass treatment through densification is very suitable and helpful technology before its effective energy recovery. Densification process of biomass is significantly influenced by various technological and material variables, which are ultimately reflected on the final solid biofuels quality. The paper deals with the experimental research of the relationship between technological and material variables during densification of fast-growing trees, roundly fast-growing willows. The main goal of presented experimental research is to determine the relationship between compression pressure and raw material particle size from a final briquettes density point of view. Experimental research was realized by single-axis densification. The impact of particle size with interaction of compression pressure and stabilization time on the quality properties of briquettes was determined. These variables interaction affects the final solid biofuels (briquettes) quality. From briquettes production point of view and from densification machines constructions point of view is very important to know about mutual interaction of these variables on final briquettes quality. The experimental findings presented here are showing the importance of mentioned variables during the densification process.
Abstract: Effect of alloying on the microstructure and mechanical properties of heat-resisting duplex stainless steel (DSS) for Mg production was investigated in this study. 25Cr-8Ni based DSS’s were cast into rectangular ingots of which the dimension was 350×350×100 mm3 . Nitrogen and Yttrium were added in the range within 0.3 in weight percent. Phase equilibrium was calculated using the FactSage®, thermodynamic software. Hot exposure, high temperature tensile and compression tests were conducted on the ingots at 1230oC, which is operation temperature employed for Mg production by Silico-thermic reduction. The steel with N and Y showed much higher strength than 310S alloy in both tensile and compression tests. By thermal exposition at 1230oC for 200 hrs, hardness of DSS containing N and Y was found to increase. Hot workability of the heat-resisting DSS was evaluated by employing hot rolling at 1230 oC. Hot shortness was observed in the ingot with N and found to disappear after addition of Y.
Abstract: Salinity is one of the major factors limiting crop
production in an arid environment. Despite its global importance
soybean production suffer the problems of salinity stress causing
damages at plant development. So it is implacable to either search for
salinity enhancement of soybean plants. Therefore, in the current
study we try to clarify the mechanism that might be involved in the
ameliorating effects of osmo-protectants such as proline and glycine
betaine as well as, compost application on soybean plants grown
under salinity stress. The experiment was conducted under
greenhouse conditions at the Graduate School of Biosphere Science
Laboratory of Hiroshima University, Japan in 2011. The experiment
was designed as a spilt-split plot based on randomized complete
block design with four replications. The treatments could be
summarized as follows; (i) salinity concentrations (0 and 15 mM), (ii)
compost treatments (0 and 24 t ha-1) and (iii) the exogenous, proline
and glycine betaine concentrations (0 mM and 25 mM) for each.
Results indicated that salinity stress induced reduction in growth and
physiological aspects (dry weight per plant, chlorophyll content, N
and K+ content) of soybean plant compared with those of the
unstressed plants. On the other hand, salinity stress led to increases in
the electrolyte leakage ratio, Na and proline contents. Special
attention was paid to, the tolerance against salt stress was observed,
the improvement of salt tolerance resulted from proline, glycine
betaine and compost were accompanied with improved K+, and
proline accumulation. While, significantly decreased electrolyte
leakage ratio and Na+ content. These results clearly demonstrate that
harmful effect of salinity could reduce on growth aspects of soybean.
Consequently, exogenous osmoprotectants combine with compost
will effectively solve seasonal salinity stress problem and are a good
strategy to increase salinity resistance of soybean in the drylands.
Abstract: Measuring the Electrocardiogram (ECG) signal is an
essential process for the diagnosis of the heart diseases. The ECG
signal has the information of the degree of how much the heart
performs its functions. In medical diagnosis and treatment systems,
Decision Support Systems processing the ECG signal are being
developed for the use of clinicians while medical examination. In this
study, a modular wireless ECG (WECG) measuring and recording
system using a single board computer and e-Health sensor platform
is developed. In this designed modular system, after the ECG signal
is taken from the body surface by the electrodes first, it is filtered and
converted to digital form. Then, it is recorded to the health database
using Wi-Fi communication technology. The real time access of the
ECG data is provided through the internet utilizing the developed
web interface.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: Groundwater is vital to the livelihoods and health of the majority of the people, since it provides almost the entire water resource for domestic, agricultural and industrial uses. Groundwater quality comprises the physical, chemical and bacteriological qualities. The present investigation was carried out to determine the physicochemical and bacteriological quality of the ground water sources in the residential areas of Karakulam Grama Panchayath in Thiruvananthapuram district, Kerala state in India. Karakulam is located in the eastern suburbs of Thiruvananthapuram city. The major drinking water source of the residents in the study area is wells. The present study aims to assess the portability and irrigational suitability of groundwater in the study area. The water samples were collected from randomly selected dug wells and bore wells in the study area during post monsoon and pre monsoon seasons of the year 2014 after a preliminary field survey. The physical, chemical and bacteriological parameters of the water samples were analyzed following standard procedures. The concentration of heavy metals (Cd, Pb and Mn) in the acid digested water samples were determined by using an Atomic Absorption Spectrophotometer. The results showed that the pH of well water samples ranged from acidic to alkaline level. In majority of well water samples (>54 %) the iron and magnesium content were found high in both the seasons studied, and the values were above the permissible limits of WHO drinking water quality standards. Bacteriological analyses showed that 63% of the wells were contaminated with total coliforms in both the seasons studied. Irrigational suitability of groundwater was assessed by determining the chemical indices like Sodium Percentage (%Na), Sodium Adsorption Ratio (SAR), Residual Sodium Carbonate (RSC), Permeability Index (PI), and the results indicate that the well water in the study area are good for irrigation purposes. Therefore, the study reveals the degradation of drinking water quality groundwater sources in Karakulam Grama Panchayath in Thiruvananthapuram District, Keralain terms of its chemical and bacteriological characteristics, and is not potable without proper treatment. In the study, more than 1/3rdof the well water samples tested were positive for total coliforms, and the bacterial contamination may pose threat to public health. The study recommends the need for periodic well water quality monitoring in the study area and to conduct awareness programs among the residents.
Abstract: The influence of cultivation factors such as content of ammonium sulfate, glucose and water in the culture medium and particle size of dry orange waste, on their bioconversion for pectinase production was studied using complete factorial design. A polygalacturonase (PG) was isolated using ion exchange chromatography under gradient elution 0-0,5 m/l NaCl (column equilibrate with acetate buffer pH 4,5), subsequently by sephadex G75 column chromatography was applied and the molecular weight was obtained about 51,28 KDa. Purified PG enzyme exhibits a pH and temperature optima of activity at 5 and 35°C respectively. Treatment of apple juice by purified enzyme extract yielded a clear juice, which was competitive with juice yielded by pure Sigma Aldrich Aspergillus niger enzyme.
Abstract: The application of cold Radio-Frequency (RF) plasma
in the conservation of cultural heritage became important in the last
decades due to the positive results obtained in decontamination
treatments. This paper presents an equipment especially designed for cold RF
plasma application on paper documents, developed within a research
project. The equipment consists in two modules: the first one is
designed for decontamination and cleaning treatments of any type of
paper supports, while the second one can be used for coating friable
papers with adequate polymers, for protection purposes. All these
operations are carried out in cold radio-frequency plasma, working in
gaseous nitrogen, at low pressure. In order to optimize the equipment parameters ancient paper
samples infested with microorganisms have been treated in nitrogen
plasma and the decontamination effects, as well as changes in surface
properties (color, pH) were assessed. The microbiological analysis
revealed complete decontamination at 6 minutes treatment duration;
only minor modifications of the surface pH were found and the
colorimetric analysis showed a slight yellowing of the support.