Abstract: This study evaluates the performance of horizontal
subsurface flow constructed wetland (HSSF-CW) for the removal of
chlorinated resin and fatty acids (RFAs) from pulp and paper mill
wastewater. The dimensions of the treatment system were 3.5 m x 1.5
m x 0.28 m with surface area of 5.25 m2, filled with fine sand and
gravel. The cell was planted with an ornamental plant species Canna
indica. The removal efficiency of chlorinated RFAs was in the range
of 92-96% at the hydraulic retention time (HRT) of 5.9 days. Plant
biomass and soil (sand and gravel) were analyzed for chlorinated
RFAs content. No chlorinated RFAs were detected in plant biomass
but detected in soil samples. Mass balance studies of chlorinated
RFAs in HSSF-CW were also carried out.
Abstract: The aim of this contribution is to present a new
approach in modeling the electrical activity of the human heart. A
recurrent artificial neural network is being used in order to exhibit a
subset of the dynamics of the electrical behavior of the human heart.
The proposed model can also be used, when integrated, as a
diagnostic tool of the human heart system.
What makes this approach unique is the fact that every model is
being developed from physiological measurements of an individual.
This kind of approach is very difficult to apply successfully in many
modeling problems, because of the complexity and entropy of the
free variables describing the complex system. Differences between
the modeled variables and the variables of an individual, measured at
specific moments, can be used for diagnostic purposes. The sensor
fusion used in order to optimize the utilization of biomedical sensors
is another point that this paper focuses on. Sensor fusion has been
known for its advantages in applications such as control and
diagnostics of mechanical and chemical processes.
Abstract: Shape optimization of the airfoil with high aspect ratio
of long endurance unmanned aerial vehicle (UAV) is performed by the
multi-objective optimization technology coupled with computational
fluid dynamics (CFD). For predicting the aerodynamic characteristics
around the airfoil the high-fidelity Navier-Stokes solver is employed
and SMOGA (Simple Multi-Objective Genetic Algorithm), which is
developed by authors, is used for solving the multi-objective
optimization problem. To obtain the optimal solutions of the design
variable (i.e., sectional airfoil profile, wing taper ratio and sweep) for
high performance of UAVs, both the lift and lift-to-drag ratio are
maximized whereas the pitching moment should be minimized,
simultaneously. It is found that the lift force and lift-to-drag ratio are
linearly dependent and a unique and dominant solution are existed.
However, a trade-off phenomenon is observed between the lift-to-drag
ratio and pitching moment. As the result of optimization, sixty-five
(65) non-dominated Pareto individuals at the cutting edge of design
spaces that is decided by airfoil shapes can be obtained.
Abstract: The purpose of this paper was to study motivation
factors affecting job performance effectiveness. This paper drew
upon data collected from an Internal Audit Staffs of Internal Audit
Line of Head Office of Krung Thai Public Company Limited.
Statistics used included frequency, percentage, mean and standard
deviation, t-test, and one-way ANOVA test. The finding revealed that
the majority of the respondents were female of 46 years of age and
over, married and live together, hold a bachelor degree, with an
average monthly income over 70,001 Baht. The majority of
respondents had over 15 years of work experience. They generally
had high working motivation as well as high job performance
effectiveness.
The hypotheses testing disclosed that employees with different
working status had different level of job performance effectiveness at
a 0.01 level of significance. Working motivation factors had an effect
on job performance in the same direction with high level. Individual
working motivation included working completion, reorganization,
working progression, working characteristic, opportunity,
responsibility, management policy, supervision, relationship with
their superior, relationship with co-worker, working position,
working stability, safety, privacy, working conditions, and payment.
All of these factors related to job performance effectiveness in the
same direction with medium level.
Abstract: In this paper, Optimum adaptive loading algorithms
are applied to multicarrier system with Space-Time Block Coding
(STBC) scheme associated with space-time processing based on
singular-value decomposition (SVD) of the channel matrix over
Rayleigh fading channels. SVD method has been employed in
MIMO-OFDM system in order to overcome subchannel interference.
Chaw-s and Compello-s algorithms have been implemented to obtain
a bit and power allocation for each subcarrier assuming instantaneous
channel knowledge. The adaptive loaded SVD-STBC scheme is
capable of providing both full-rate and full-diversity for any number
of transmit antennas. The effectiveness of these techniques has
demonstrated through the simulation of an Adaptive loaded SVDSTBC
system, and the comparison shown that the proposed
algorithms ensure better performance in the case of MIMO.
Abstract: The communication networks development and
advancement during two last decades has been toward a single goal
and that is gradual change from circuit-switched networks to packed
switched ones. Today a lot of networks operates are trying to
transform the public telephone networks to multipurpose packed
switch. This new achievement is generally called "next generation
networks". In fact, the next generation networks enable the operators
to transfer every kind of services (sound, data and video) on a
network. First, in this report the definition, characteristics and next
generation networks services and then ad-hoc networks role in the
next generation networks are studied.
Abstract: To provide a better understanding of fair share policies supported by current production schedulers and their impact on scheduling performance, A relative fair share policy supported in four well-known production job schedulers is evaluated in this study. The experimental results show that fair share indeed reduces heavy-demand users from dominating the system resources. However, the detailed per-user performance analysis show that some types of users may suffer unfairness under fair share, possibly due to priority mechanisms used by the current production schedulers. These users typically are not heavy-demands users but they have mixture of jobs that do not spread out.
Abstract: An n×n matrix is called an N1 0 -matrix if all principal minors are non-positive and each entry is non-positive. In this paper, we study the partial non-combinatorially symmetric N1 0 -matrix completion problems if the graph of its specified entries is a transitive tournament or a double cycle. In general, these digraphs do not have N1 0 -completion. Therefore, we have given sufficient conditions that guarantee the existence of the N1 0 -completion for these digraphs.
Abstract: Energy generated by the force of water in hydropower
can provide a more sustainable, non-polluting alternative to fossil
fuels, along with other renewable sources of energy, such as wind,
solar and tidal power, bio energy and geothermal energy. Small scale
hydroelectricity in Iran is well suited for “off-grid" rural electricity
applications, while other renewable energy sources, such as wind,
solar and biomass, can be beneficially used as fuel for pumping
groundwater for drinking and small scale irrigation in remote rural
areas or small villages. Small Hydro Power plants in Iran have very
low operating and maintenance costs because they consume no fossil
or nuclear fuel and do not involve high temperature processes. The
equipment is relatively simple to operate and maintain. Hydropower
equipment can adjust rapidly to load changes. The extended
equipment life provides significant economic advantages. Some
hydroelectric plants installed 100 years ago still operate reliably. The
Polkolo river is located on Karun basin at southwest of Iran. Situation
and conditions of Polkolo river are evaluated for construction of
small hydropower in this article. The topographical conditions and
the existence of permanent water from springs provide the suitability
to install hydroelectric power plants on the river Polkolo. The
cascade plant consists of 9 power plants connected with each other
and is having the total head as 1100m and discharge about 2.5cubic
meter per second. The annual production of energy is 105.5 million
kwh.
Abstract: The paper considers a novel modular and intrinsically safe redundant robotic system with biologically inspired actuators (pneumatic artificial muscles and rubber bellows actuators). Similarly to the biological systems, the stiffness of the internal parallel modules, representing 2 DOF joints in the serial robotic chains, is controlled by co-activation of opposing redundant actuator groups in the null-space of the module Jacobian, without influencing the actual robot position. The decoupled position/stiffness control allows the realization of variable joint stiffness according to different force-displacement relationships. The variable joint stiffness, as well as limited pneumatic muscle/bellows force ability, ensures internal system safety that is crucial for development of human-friendly robots intended for human-robot collaboration. The initial experiments with the system prototype demonstrate the capabilities of independently, simultaneously controlling both joint (Cartesian) motion and joint stiffness. The paper also presents the possible industrial applications of snake-like robots built using the new modules.
Abstract: Photoplethysmography is a simple measurement of the
variation in blood volume in tissue. It detects the pulse signal of heart
beat as well as the low frequency signal of vasoconstriction and
vasodilation. The transmission type measurement is limited to only a
few specific positions for example the index finger that have a short
path length for light. The reflectance type measurement can be
conveniently applied on most parts of the body surface. This study
analyzed the factors that determine the quality of reflectance
photoplethysmograph signal including the emitter-detector distance,
wavelength, light intensity, and optical properties of skin tissue.
Light emitting diodes (LEDs) with four different visible
wavelengths were used as the light emitters. A phototransistor was
used as the light detector. A micro translation stage adjusts the
emitter-detector distance from 2 mm to 15 mm.
The reflective photoplethysmograph signals were measured on
different sites. The optimal emitter-detector distance was chosen to
have a large dynamic range for low frequency drifting without signal
saturation and a high perfusion index. Among these four wavelengths,
a yellowish green (571nm) light with a proper emitter-detection
distance of 2mm is the most suitable for obtaining a steady and reliable
reflectance photoplethysmograph signal
Abstract: This paper introduces a new method called ARPDC (Advanced Robust Parallel Distributed Compensation) for automatic control of nonlinear systems. This method improves a quality of robust control by interpolating of robust and optimal controller. The weight of each controller is determined by an original criteria function for model validity and disturbance appreciation. ARPDC method is based on nonlinear Takagi-Sugeno (T-S) fuzzy systems and Parallel Distributed Compensation (PDC) control scheme. The relaxed stability conditions of ARPDC control of nominal system have been derived. The advantages of presented method are demonstrated on the inverse pendulum benchmark problem. From comparison between three different controllers (robust, optimal and ARPDC) follows, that ARPDC control is almost optimal with the robustness close to the robust controller. The results indicate that ARPDC algorithm can be a good alternative not only for a robust control, but in some cases also to an adaptive control of nonlinear systems.
Abstract: The influences of pulsed electric fields on early
physiological development in Arabidopsis thaliana were studied.
Inside a 4-mm electroporation cuvette, pre-germination seeds were
subjected to high-intensity, nanosecond electrical pulses generated
using laboratory-assembled pulsed electric field system. The field
strength was varied from 5 to 20 kV.cm-1 and the pulse width and the
pulse number were maintained at 10 ns and 100, respectively,
corresponding to the specific treatment energy from 300 J.kg-1 to 4.5
kJ.kg-1. Statistical analyses on the average leaf area 5 and 15 days
following pulsed electric field treatment showed that the effects
appear significant the second week after treatments with a maximum
increase of 80% compared to the control (P < 0.01).
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: Nowadays, the pace of business change is such that,
increasingly, new functionality has to be realized and reliably
installed in a matter of days, or even hours. Consequently, more and
more business processes are prone to a continuous change. The
objective of the research in progress is to use the MAP model, in a
conceptual modeling method for flexible and adaptive business
process. This method can be used to capture the flexibility
dimensions of a business process; it takes inspiration from
modularity concept in the object oriented paradigm to establish a
hierarchical construction of the BP modeling. Its intent is to provide
a flexible modeling that allows companies to quickly adapt their
business processes.
Abstract: The aim of this paper is to provide a better
understanding of the implementation of Project Management
practices by UiTM contractors to ensure project success. A
questionnaire survey was administered to 120 UiTM contractors in
Malaysia. The purpose of this method was to gather information on
the contractors- project background and project management skills. It
was found that all of the contractors had basic knowledge and
understanding of project management skills. It is suggested that a
reasonable project plan and an appropriate organizational structure
are influential factors for project success. It is recommended that the
contractors need to have an effective program of work and up to date
information system are emphasized.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).