Abstract: A solar receiver is designed for operation under
extremely uneven heat flux distribution, cyclic weather, and cloud
transient cycle conditions, which can include large thermal stress and
even receiver failure. In this study, the effect of different oil velocity
on convection coefficient factor and impact of wind velocity on local
Nusselt number by Finite Volume Method will be analyzed. This
study is organized to give an overview of the numerical modeling
using a MATLAB software, as an accurate, time efficient and
economical way of analyzing the heat transfer trends over stationary
receiver tube for different Reynolds number. The results reveal when
oil velocity is below 0.33m/s, the value of convection coefficient is
negligible at low temperature. The numerical graphs indicate that
when oil velocity increases up to 1.2 m/s, heat convection coefficient
increases significantly. In fact, a reduction in oil velocity causes a
reduction in heat conduction through the glass envelope. In addition,
the different local Nusselt number is reduced when the wind blows
toward the concave side of the collector and it has a significant effect
on heat losses reduction through the glass envelope.
Abstract: Large-scale machine tools for the manufacturing of
large work pieces, e.g. blades, casings or gears for wind turbines,
feature pose-dependent dynamic behavior. Small structural damping
coefficients lead to long decay times for structural vibrations that
have negative impacts on the production process. Typically, these
vibrations are handled by increasing the stiffness of the structure by
adding mass. This is counterproductive to the needs of sustainable
manufacturing as it leads to higher resource consumption both in
material and in energy. Recent research activities have led to higher
resource efficiency by radical mass reduction that is based on controlintegrated
active vibration avoidance and damping methods. These
control methods depend on information describing the dynamic
behavior of the controlled machine tools in order to tune the
avoidance or reduction method parameters according to the current
state of the machine. This paper presents the appearance, consequences and challenges
of the pose-dependent dynamic behavior of lightweight large-scale
machine tool structures in production. It starts with the theoretical
introduction of the challenges of lightweight machine tool structures
resulting from reduced stiffness. The statement of the pose-dependent
dynamic behavior is corroborated by the results of the experimental
modal analysis of a lightweight test structure. Afterwards, the
consequences of the pose-dependent dynamic behavior of lightweight
machine tool structures for the use of active control and vibration
reduction methods are explained. Based on the state of the art of
pose-dependent dynamic machine tool models and the modal
investigation of an FE-model of the lightweight test structure, the
criteria for a pose-dependent model for use in vibration reduction are
derived. The description of the approach for a general posedependent
model of the dynamic behavior of large lightweight
machine tools that provides the necessary input to the aforementioned
vibration avoidance and reduction methods to properly tackle
machine vibrations is the outlook of the paper.
Abstract: The importance of agribusiness development is
proved in accordance with the trends in the agricultural sector of
Georgia. Agribusiness environment and the consequences of the
agricultural reforms are evaluated. The factors hindering the
development of agribusiness are revealed and the ways for
overcoming these problems are suggested. SWOT analysis is done in
order to identify the needs of agribusiness. The needs of agribusiness
development in Georgia are evaluated by priorities: prevention of
diseases and reduction of the harm caused by these diseases,
accessibility of long-term agricultural loans with low interest rates,
improving qualification of farmers, the level of education and usage
of modern technologies, changes in legislation, accessibility to high
quality agricultural machinery, and the development of infrastructure.
Based on the outcomes of the research, agribusiness development
strategies in Georgia are suggested and appropriate priorities of
economic policy are determined. Conclusions are made and based on
these conclusions, some recommendations are suggested.
Abstract: This research tested the performance of alternative
warehouse designs concerning the picking process. The chosen
performance measures were Travel Distance and Total Fulfilment
Time. An explanatory case study was built up around a model
implemented with SIMUL8. Hypotheses were set by selecting
outcomes from the literature survey matching popular empirical
findings. 17.4% reductions were found for Total Fulfilment Time and
Resource Utilisation. The latter was then used as a proxy for
operational efficiency. Literal replication of theoretical data-patterns
was considered as an internal validity sign. Assessing the estimated
changes benefits ahead of implementation was found to be a
contribution to practice.
Abstract: In this paper, a novel Linear Feedback Shift Register
(LFSR) with Look Ahead Clock Gating (LACG) technique is
presented to reduce the power consumption in modern processors
and System-on-Chip. Clock gating is a predominant technique used
to reduce unwanted switching of clock signals. Several clock gating
techniques to reduce the dynamic power have been developed, of
which LACG is predominant. LACG computes the clock enabling
signals of each flip-flop (FF) one cycle ahead of time, based on the
present cycle data of the flip-flops on which it depends. It overcomes
the timing problems in the existing clock gating methods like datadriven
clock gating and Auto-Gated flip-flops (AGFF) by allotting a
full clock cycle for the determination of the clock enabling signals.
Further to reduce the power consumption in LACG technique, FFs
can be grouped so that they share a common clock enabling signal.
Simulation results show that the novel grouped LFSR with LACG
achieves 15.03% power savings than conventional LFSR with LACG
and 44.87% than data-driven clock gating.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Fires is one of the main types of disturbances that
shape ecosystems in the Mediterranean region. However nowadays,
climate alterations towards higher temperatures result on increased
levels of fire intensity, frequency and spread as well as difficulties for
natural regeneration to occur. Thasos Island is one of the Greek
islands that has experienced those problems. Since 1984, a series of
wildfires led to the reduction of forest cover from 61.6% to almost
20%. The negative impacts were devastating in many different
aspects for the island. The absence of plant cover, post-wildfire
precipitation and steep slopes were the major factors that induced
severe soil erosion and intense floods. That also resulted to serious
economic problems to the local communities and the inability of the
burnt areas to regenerate naturally. Despite the substantial amount of
published work regarding Thasos wildfires, there is no information
related to post-wildfire effects on factors such as soil erosion. More
research related to post-fire effects should help to an overall
assessment of the negative impacts of wildfires on land degradation
through processes such as soil erosion and flooding.
Abstract: A clay soil classified as A-7-6 and CH soil according
to AASHTO and unified soil classification system respectively, was
stabilized using A-3 soil (AASHTO soil classification system). The
clay soil was replaced with 0%, 10%, 20%, to 100% A-3 soil,
compacted at both British Standard Light (BSL) and British Standard
Heavy (BSH) compaction energy levels and using Unconfined
Compressive Strength (UCS) as evaluation criteria. The Maximum
Dry Density (MDD) of the treated soils at both the BSL and BSH
compaction energy levels showed increase from 0% to 40% A-3 soil
replacement after which the values reduced to 100% replacement.
The trend of the Optimum Moisture Content (OMC) with varied A-3
soil replacement was similar to that of MDD but in a reversed order.
The OMC reduced from 0% to 40% A-3 soil replacement after which
the values increased to 100% replacement. This trend was attributed
to the observed reduction in void ratio from 0% to 40% replacement
after which the void ratio increased to 100% replacement. The
maximum UCS for the soil at varied A-3 soil replacement increased
from 272 and 770 kN/m2 for BSL and BSH compaction energy level
at 0% replacement to 295 and 795 kN/m2 for BSL and BSH
compaction energy level respectively at 10% replacement after which
the values reduced to 22 and 60 kN/m2 for BSL and BSH compaction
energy level respectively at 70% replacement. Beyond 70%
replacement, the mixtures could not be moulded for UCS test.
Abstract: During machining process, chatter is an unavoidable
phenomenon. Boring bars possess the cantilever shape and due to
this, it is subjected to chatter. The adverse effect of chatter includes
the increase in temperature which will leads to excess tool wear. To
overcome these problems, in this investigation, Cartridge brass (Cu –
70% and Zn – 30%) is passively fixed on the boring bar and also
clearance is provided in order to reduce the displacement, tool wear
and cutting temperature. A conventional all geared lathe is attached
with vibrometer and pyrometer is used to measure the displacement
and temperature. The influence of input parameters such as cutting
speed, depth of cut and clearance on temperature, tool wear and
displacement are investigated for various cutting conditions. From
the result, the optimum conditions to obtain better damping in boring
process for chatter reduction is identified.
Abstract: Revenue leakages are one of the major challenges
manufacturers face in production processes, as most of the input
materials that should emanate as products from the lines are lost as
waste. Rather than generating income from material input which is
meant to end-up as products, losses are further incurred as costs in
order to manage waste generated. In addition, due to the lack of a
clear view of the flow of resources on the lines from input to output
stage, acquiring information on the true cost of waste generated have
become a challenge. This has therefore given birth to the
conceptualization and implementation of waste minimization
strategies by several manufacturing industries. This paper reviews the
principles and applications of three environmental management
accounting tools namely Activity-based Costing (ABC), Life-Cycle
Assessment (LCA) and Material Flow Cost Accounting (MFCA) in
the manufacturing industry and their effectiveness in curbing revenue
leakages. The paper unveils the strengths and limitations of each of
the tools; beaming a searchlight on the tool that could allow for
optimal resource utilization, transparency in production process as
well as improved cost efficiency. Findings from this review reveal
that MFCA may offer superior advantages with regards to the
provision of more detailed information (both in physical and
monetary terms) on the flow of material inputs throughout the
production process compared to the other environmental accounting
tools. This paper therefore makes a case for the adoption of MFCA as
a viable technique for the identification and reduction of waste in
production processes, and also for effective decision making by
production managers, financial advisors and other relevant
stakeholders.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: A mixed method for model order reduction is
presented in this paper. The denominator polynomial is derived by
matching both Markov parameters and time moments, whereas
numerator polynomial derivation and error minimization is done
using Genetic Algorithm. The efficiency of the proposed method can
be investigated in terms of closeness of the response of reduced order
model with respect to that of higher order original model and a
comparison of the integral square error as well.
Abstract: Red pepper (Capsicum annum L.) has long been
recognized as a good source of antioxidants, being rich in ascorbic
acid and other phytochemicals. In Turkish cuisine red pepper is
sometimes consumed raw in salads and baked as a garnish, but its
most wide consumption type is red pepper paste. The processing of
red pepper into pepper paste includes various thermal treatment steps
such as heating and pasteurizing. There are reports demonstrating an
enhancement or reduction in antioxidant activity of vegetables after
thermal treatment. So this study was conducted to investigate the
total phenolic, ascorbic acid and total carotenoids as well as free
radical scavenging activity of raw red pepper and various red pepper
pastes obtainable on the market. The samples were analyzed for
radical-scavenging activity (RSA) and total polyphenol (TP) content
using 1,1-diphenyl-2-picrylhydrazyl (DPPH) and Folin-Ciocalteu
methods, respectively. Total carotenoids and ascorbic acid contents
were determined spectrophotometrically. Results suggest that hot
pepper paste contained significantly (P0.05) difference in RSA, ascorbic acid and total carotenoids
content between sweet and hot red pepper paste products. It is
concluded that the red pepper paste, that has a wide range of
consumption in Turkish cuisine, presents a good dose of phenolic
compounds and antioxidant capacity and it should be regarded as a
functional food.
Abstract: An integrated modeling approach was used in this study for energy planning and climate change mitigation assessment. The main objective of this study was to develop various green-house gas (GHG) mitigations scenarios in the energy demand and supply sectors for the state of Florida. The Long range energy alternative planning (LEAP) model was used in this study to examine the energy alternative and GHG emissions reduction scenarios for short and long term (2010-2050). One of the energy analysis and GHG mitigation scenarios was developed by taking into account the available renewable energy resources potential for power generation in the state of Florida. This will help to compare and analyze the GHG reduction measure against “Business As Usual” and ‘State of Florida Policy” scenarios. Two master scenarios: “Electrification” and “Energy efficiency and Lifestyle” were developed through combination of various mitigation scenarios: technological changes and energy efficiency and conservation. The results show a net reduction of the energy demand and GHG emissions by adopting these two energy scenarios compared to the business as usual.
Abstract: The market competition is moving from the single
firm to the whole supply chain because of increasing competition and
growing need for operational efficiencies and customer orientation.
Supply chain management allows companies to look beyond their
organizational boundaries to develop and leverage resources and
capabilities of their supply chain partners. This creates competitive
advantages in the marketplace and because of this SCM has acquired
strategic importance. Lean Approach is a management strategy that focuses on reducing
every type of waste present in an organization. This approach is
becoming more and more popular among supply chain managers. The supply chain application of lean approach is not frequent. In
particular, it is not well studied which are the impacts of lean
approach principles in a supply chain context. In literature there are
only few studies aimed at understanding the qualitative impact of the
lean approach in supply chains. Therefore, the goal of this research
work is to study the impacts of lean principles implementation along
a supply chain. To achieve this, a simulation model of a threeechelon
multi-product supply chain has been built. Kanban system (and several priority policies) and setup time
reduction degrees are implemented in the lean-configured supply
chain to apply pull and lot-sizing decrease principles respectively. To
evaluate the benefits of lean approach, lean supply chain is compared
with an EOQ-configured supply chain. The simulation results show
that Kanban system and setup-time reduction improve inventory
stock level. They also show that logistics efforts are affected to lean
implementation degree. The paper concludes describing
performances of lean supply chain in different contexts.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.
Abstract: High moisture content in fruits generates post-harvest
problems such as mechanical, biochemical, microbial and physical
losses. Dehydration, which is based on the reduction of water activity
of the fruit, is a common option for overcoming such losses.
However, regular hot air drying could affect negatively the quality
properties of the fruit due to the long residence time at high
temperature. Power ultrasound (US) application during the
convective drying has been used as a novel method able to enhance
drying rate and, consequently, to decrease drying time. In the present
study, a new approach was tested to evaluate the effect of US on the
drying time, the final antioxidant activity (AA) and the total
polyphenol content (TPC) of banana slices (BS), mango slices (MS)
and guava slices (GS). There were also studied the drying kinetics
with nine different models from which water effective diffusivities
(Deff) (with or without shrinkage corrections) were calculated.
Compared with the corresponding control tests, US assisted drying
for fruit slices showed reductions in drying time between 16.23 and
30.19%, 11.34 and 32.73%, and 19.25 and 47.51% for the MS, BS
and GS respectively. Considering shrinkage effects, Deff calculated
values ranged from 1.67*10-10 to 3.18*10-10 m2/s, 3.96*10-10 and
5.57*10-10 m2/s and 4.61*10-10 to 8.16*10-10 m2/s for the BS, MS and
GS samples respectively. Reductions of TPC and AA (as DPPH)
were observed compared with the original content in fresh fruit data
in all kinds of drying assays.
Abstract: This paper describes a subarray based low
computational design method of multiuser massive multiple
input multiple output (MIMO) system. In our previous works, use of
large array is assumed only in transmitter, but this study considers
the case both of transmitter and receiver sides are equipped with
large array antennas. For this aim, receive arrays are also divided
into several subarrays, and the former proposed method is modified
for the synthesis of a large array from subarrays in both ends.
Through computer simulations, it is verified that the performance
of the proposed method is degraded compared with the original
approach, but it can achieve the improvement in the aspect of
complexity, namely, significant reduction of the computational load
to the practical level.
Abstract: The problem of degradation of agricultural residues
from palm oil industry is increasing due to its expansion.
Lignocelloulosic waste from these industry represent large amount of
unutilized resources, this is due to their high lignin content. Since
white rot fungi are capable of degrading lignin, its potential for the
degradation of lignocelloulosic waste from palm oil industry was
accessed. The lignocellluloses content was measured before and after
biodegradation and the rate of reduction was determined. From the
results of the biodegradation, it was observed that hemicellulose
reduces by 22.62%, cellulose by 20.97% and lignin by 10.65% from
the initials lignocelluloses contents. Thus, to improve the digestibility
of palm oil mesocarp fibre, treatment by white rot-fungi is
recommended.
Abstract: Different countries have introduced different schemes
and policies to counter global warming. The rationale behind the
proposed policies and the potential barriers to successful
implementation of the policies adopted by the countries were
analyzed and estimated based on different models. It is argued that
these models enhance the transparency and provide a better
understanding to the policy makers. However, these models are
underpinned with several structural and baseline assumptions. These
assumptions, modeling features and future prediction of emission
reductions and other implication such as cost and benefits of a
transition to a low-carbon economy and its economy wide impacts
were discussed. On the other hand, there are potential barriers in the
form political, financial, and cultural and many others that pose a
threat to the mitigation options.