Abstract: Retinal prostheses have been successful in eliciting
visual responses in implanted subjects. As these prostheses progress,
one of their major limitations is the need for increased resolution. As
an alternative to increasing the number of electrodes, virtual
electrodes may be used to increase the effective resolution of current
electrode arrays. This paper presents a virtual electrode technique
based upon time-offsets between stimuli. Two adjacent electrodes are
stimulated with identical pulses with too short of pulse widths to
activate a neuron, but one has a time offset of one pulse width. A
virtual electrode of twice the pulse width was then shown to appear in
the center, with a total width capable of activating a neuron. This can
be used in retinal implants by stimulating electrodes with pulse
widths short enough to not elicit responses in neurons, but with their
combined pulse width adequate to activate a neuron in between them.
Abstract: Under the variation of crude oil price and the impact of
greenhouse effect, it is urgent to find a potential alternative fuel.
Among these alternative fuels, non edible plant oils are the most
potential ones, because they don-t have the problem of food and
cropland competitions. Among the non-edible plant oils, Jatropha oil
is the most potential one. Jatropha oil is non-eatable oil and has good
oil quality and low temperature performance. It has potential to
become one of the most competitive biomass crude oils. The crude
plant oil will be blended with diesel fuel to be tested in a power
generator. The international collaboration between Taiwan and
Indonesia on the production of Jatropha in Indonesia will also be
presented in this study.
Abstract: The significance of environmental protection is wellknown in today's world. The execution of any program depends on sufficient knowledge and required familiarity with environment and its pollutants. Taking advantage of a systematic method, as a new science, in environmental planning can solve many problems. In this article, air pollution in Tehran and its relationship with health and population growth have been analyzed using dynamic systems. Firstly, by using casual loops, the relationship between the parameters effective on air pollution in Tehran were taken into consideration, then these casual loops were turned into flow diagrams [6], and finally, they were simulated using the software Vensim [16]in order to conclude what the effect of each parameter will be on air pollution in Tehran in the next 10 years, how changing of one or more parameters influences other parameters, and which parameter among all other parameters requires to be controlled more.
Abstract: To enhance installation security, a LNG storage in Rudong of Jiangsu province was adopted as a practical work, and it was analyzed by nonlinear finite element method to research overall and local stability performance, as well as the stress and deformation under the action of wind load and self-weight. Results indicate that deformation is tiny when steel mesh maintains as an overall ring, and stress caused by vertical bending moment and tension of bottom tie wire are also in the safe range. However, axial forces of lap reinforcement in adjacent steel mesh exceed the ultimate bearing capacity of tie wire. Hence, tie wires are ruptured; single mesh loses lateral connection and turns into monolithic status as the destruction of overall structure. Further more, monolithic steel mesh is led to collapse by the damage of bottom connection. So, in order to prevent connection failure and enhance installation security, the overlapping parts of steel mesh should be taken more reliable measures.
Abstract: This study aims to assess the potential of solar energy technology for improving access to water and hence the livelihood strategies of rural communities in Baja California Sur, Mexico. It focuses on livestock ranches and photovoltaic water-pumptechnology as well as other water extraction methods. The methodology used are the Sustainable Livelihoods and the Appropriate Technology approaches. A household survey was applied in June of 2006 to 32 ranches in the municipality, of which 22 used PV pumps; and semi-structured interviews were conducted. Findings indicate that solar pumps have in fact helped people improve their quality of life by allowing them to pursue a different livelihood strategy and that improved access to water -not necessarily as more water but as less effort to extract and collect it- does not automatically imply overexploitation of the resource; consumption is based on basic needs as well as on storage and pumping capacity. Justification for such systems lies in the avoidance of logistical problems associated to fossil fuels, PV pumps proved to be the most beneficial when substituting gasoline or diesel equipment but of dubious advantage if intended to replace wind or gravity systems. Solar water pumping technology-s main obstacle to dissemination are high investment and repairs costs and it is therefore not suitable for all cases even when insolation rates and water availability are adequate. In cases where affordability is not an obstacle it has become an important asset that contributes –by means of reduced expenses, less effort and saved time- to the improvement of livestock, the main livelihood provider for these ranches.
Abstract: The optimal control is one of the possible controllers
for a dynamic system, having a linear quadratic regulator and using
the Pontryagin-s principle or the dynamic programming method .
Stochastic disturbances may affect the coefficients (multiplicative
disturbances) or the equations (additive disturbances), provided that
the shocks are not too great . Nevertheless, this approach encounters
difficulties when uncertainties are very important or when the probability
calculus is of no help with very imprecise data. The fuzzy
logic contributes to a pragmatic solution of such a problem since it
operates on fuzzy numbers. A fuzzy controller acts as an artificial
decision maker that operates in a closed-loop system in real time.
This contribution seeks to explore the tracking problem and control
of dynamic macroeconomic models using a fuzzy learning algorithm.
A two inputs - single output (TISO) fuzzy model is applied to the
linear fluctuation model of Phillips and to the nonlinear growth model
of Goodwin.
Abstract: Collaborative planning, forecasting and
replenishment (CPFR) coordinates the various supply chain
management activities including production and purchase planning,
demand forecasting and inventory replenishment between supply
chain trading partners. This study proposes a systematic way of
analyzing CPFR supporting factors using fuzzy cognitive map
(FCM) approach. FCMs have proven particularly useful for solving
problems in which a number of decision variables and
uncontrollable variables are causally interrelated. Hence the FCMs
of CPFR are created to show the relationships between the factors
that influence on effective implementation of CPFR in the supply
chain.
Abstract: A numerical study has been conducted to investigate the influence of fin pitch and relative humidity on the heat transfer performance of the fin-and-tube heat exchangers having plain fin geometry under dehumidifying conditions. The analysis is done using the ratio between the heat transfer coefficients in totally wet conditions and those in totally dry conditions using the appropriate correlations for both dry and wet conditions. For a constant relative humidity, it is found that the heat transfer coefficient increases with the increase of the air frontal velocity. By contrast, the fin efficiency decreases when the face velocity is increased. Apparently, this phenomenon is attributed to the path of condensate drainage. For the influence of relative humidity, the results showed an increase in heat transfer performance and a decrease in wet fin efficiency when relative humidity increases. This is due to the higher amount of mass transfer encountered at higher relative humidity. However, it is found that the effect of fin pitch on the heat transfer performance depends strongly on the face velocity. At lower frontal velocity the heat transfer increases with fin pitch. Conversely, an increase in fin pitch gives lower heat transfer coefficients when air velocity is increased.
Abstract: This paper proposes an adaptive sliding mode
controller which combines adaptive control and sliding
mode control to control a nonlinear robotic manipulator
with uncertain parameters. We use an adaptive algorithm
based on the concept of sliding mode control to alleviate the
chattering phenomenon of control input. Adaptive laws are
developed to obtain the gain of switching input and the
boundary layer parameters. The stability and convergence
of the robotic manipulator control system are guaranteed
by applying the Lyapunov theorem. Simulation results
demonstrate that the chattering of control input can be
alleviated effectively. The proposed controller scheme can
assure robustness against a large class of uncertainties and
achieve good trajectory tracking performance.
Abstract: A graph G is fractional k-covered if for each edge e of
G, there exists a fractional k-factor h, such that h(e) = 1. If k = 2,
then a fractional k-covered graph is called a fractional 2-covered
graph. The binding number bind(G) is defined as follows,
bind(G) = min{|NG(X)|
|X|
: ├ÿ = X Ôèå V (G),NG(X) = V (G)}.
In this paper, it is proved that G is fractional 2-covered if δ(G) ≥ 4
and bind(G) > 5
3 .
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: In mammalian reproductive tract, the oviduct secretes
huge number of growth factors and cytokines that create an optimal
micro-environment for the initial stages of preimplantation embryos.
Secretion of these growth factors is stage-specific. Among them,
VEGF is a potent mitogen for vascular endothelium and stimulates
vascular permeability. Apart from angiogenesis, VEGF in the oviduct
may be involved in regulating the oocyte maturation and subsequent
developmental process during embryo production in vitro. In
experiment 1, to evaluate the effect of VEGF during IVM of porcine
COC and subsequent developmental ability after PA and SCNT. The
results from these experiments indicated that maturation rates among
the different VEGF concentrations were not significant different. In
experiment 2, total intracellular GSH concentrations of oocytes
matured with VEGF (5-50 ng/ml) were increased significantly
compared to a control and VEGF group (500 ng/ml). In experiment 3,
the blastocyst formation rates and total cell number per blastocyst
after parthenogenesis of oocytes matured with VEGF (5-50 ng/ml)
were increased significantly compared to a control and VEGF group
(500 ng/ml). Similarly, in experiment 4, the blastocyst formation rate
and total cell number per blastocyst after SCNT and IVF of oocytes
matured with VEGF (5 ng/ml) were significantly higher than that of
oocytes matured without VEGF group. In experiment 5, at 10 hour
after the onset of IVF, pronuclear formation rate was evaluated.
Monospermy was significantly higher in VEGF-matured oocytes than
in the control, and polyspermy and sperm penetration per oocyte
were significantly higher in the control group than in the VEGFmatured
oocytes. Supplementation with VEGF during IVM
significantly improved male pronuclear formation as compared with
the control. In experiment 6, type III cortical granule distribution in
oocytes was more common in VEGF-matured oocytes than in the
control. In conclusion, the present study suggested that
supplementation of VEGF during IVM may enhance the
developmental potential of porcine in vitro embryos through increase
of the intracellular GSH level, higher MPN formation and increased
fertilization rate as a consequence of an improved cytoplasmic
maturation.
Abstract: This paper develops a pedometer with a three-axis acceleration sensor that can be placed with any angle. The proposed pedometer measures the number of steps while users walk, jog or run. It can be worn on users’ waistband or placed within pocket or backpack. The work address to improve on the general pedometers, which can only be used in a single direction or can only count of steps without the continuous exercise judgment mechanism. Finally, experimental results confirm the superior performance of the proposed pedometer.
Abstract: In this paper, an magnetorheological (MR) mount with
fuzzy sliding mode controller (FSMC) is studied for vibration
suppression when the system is subject to base excitations. In recent
years, magnetorheological fluids are becoming a popular material in
the field of the semi-active control. However, the dynamic equation of
an MR mount is highly nonlinear and it is difficult to identify. FSMC
provides a simple method to achieve vibration attenuation of the
nonlinear system with uncertain disturbances. This method is capable
of handling the chattering problem of sliding mode control effectively
and the fuzzy control rules are obtained by using the Lyapunov
stability theory. The numerical simulations using one-dimension and
two-dimension FSMC show effectiveness of the proposed controller
for vibration suppression. Further, the well-known skyhook control
scheme and an adaptive sliding mode controller are also included in
the simulation for comparison with the proposed FSMC.
Abstract: The problem of N cracks interaction in an isotropic
elastic solid is decomposed into a subproblem of a homogeneous solid
without crack and N subproblems with each having a single crack
subjected to unknown tractions on the two crack faces. The unknown
tractions, namely pseudo tractions on each crack are expanded into
polynomials with unknown coefficients, which have to be determined
by the consistency condition, i.e. by the equivalence of the original
multiple cracks interaction problem and the superposition of the N+1
subproblems. In this paper, Kachanov-s approach of average tractions
is extended into the method of moments to approximately impose the
consistence condition. Hence Kachanov-s method can be viewed as
the zero-order method of moments. Numerical results of the stress
intensity factors are presented for interactions of two collinear cracks,
three collinear cracks, two parallel cracks, and three parallel cracks.
As the order of moment increases, the accuracy of the method of
moments improves.
Abstract: This research was undertaken to study enzymatic activity in the shoots, roots, and rhizosphere of alfalfa (Medicago sativa L.) grown in quartz sand that was uncontaminated and
contaminated with phenanthrene at concentrations of 10 and 100 mg kg-1. The higher concentration of phehanthrene had a distinct
phytotoxic effect on alfalfa, inhibiting seed germination energy, plant survival, and biomass accumulation. The plant stress response to the
environmental pollution was an increase in peroxidase activity. Peroxidases were the predominant enzymes in the alfalfa shoots and
roots. The peroxidase profile in the shoots differed from that in the roots and had different isoenzyme numbers. 2,2'-Azinobis-(3-ethylbenzo-thiazoline-6-sulphonate) (ABTS) peroxidase was
predominant in the shoots, and 2,7-diaminofluorene (2,2-DAF)
peroxidase was predominant in the roots. Under the influence of
phenanthrene, the activity of 2,7-DAF peroxidase increased in the
shoots, and the activity of ABTS peroxidase increased in the roots.
Alfalfa root peroxidases were the prevalent enzyme systems in the
rhizosphere sand. Examination of the activity of alfalfa root
peroxidase toward phenanthrene revealed the possibility of
involvement of the plant enzyme in rhizosphere degradation of the
PAH.
Abstract: This paper presents comparison among methods of
determination of the characteristic polynomial coefficients. First, the
resultant systems from the methods are compared based on frequency
criteria such as the closed loop bandwidth, gain and phase margins.
Then the step responses of the resultant systems are compared on the
basis of the transient behavior criteria including overshoot, rise time,
settling time and error (via IAE, ITAE, ISE and ITSE integral
indices). Also relative stability of the systems is compared together.
Finally the best choices in regards to the above diverse criteria are
presented.
Abstract: The research was designed to examine the relationship
between the development of muscle fatigue and the effect it has on
sport performance, specifically during maximal voluntary
contraction. This kind of this investigation using simultaneous
electrophysiological and mechanical recordings, based on advanced
mathematical processing, allows us to get parameters, and indexes in
a short time, and finally, the mapping to use for the thorough
investigation of the muscle contraction force, respectively the
phenomenon of local muscle fatigue, both for athletes and other
subjects.
Abstract: The ongoing effort to develop an in-house
compressible solver with multi-disciplinary physics is presented in
this paper. Basic compressible solver combined with IBM technique
provides us an effective numerical tool able to tackle the physics
phenomena and especially physic phenomena involved in Solid
Rocket Motors (SRMs). Main principles are introduced step by step
describing its implementation. This paper sheds light on the whole
potentiality of our proposed numerical model and we strongly believe
a way to introduce multi-physics mechanisms strongly coupled is
opened to ablation in nozzle, fluid/structure interaction and burning
propellant surface with time.
Abstract: Rotor Flux based Model Reference Adaptive System
(RF-MRAS) is the most popularly used conventional speed
estimation scheme for sensor-less IM drives. In this scheme, the
voltage model equations are used for the reference model. This
encounters major drawbacks at low frequencies/speed which leads to
the poor performance of RF-MRAS. Replacing the reference model
using Neural Network (NN) based flux estimator provides an
alternate solution and addresses such drawbacks. This paper
identifies an NN based flux estimator using Single Neuron Cascaded
(SNC) Architecture. The proposed SNC-NN model replaces the
conventional voltage model in RF-MRAS to form a novel MRAS
scheme named as SNC-NN-MRAS. Through simulation the proposed
SNC-NN-MRAS is shown to be promising in terms of all major
issues and robustness to parameter variation. The suitability of the
proposed SNC-NN-MRAS based speed estimator and its advantages
over RF-MRAS for sensor-less induction motor drives is
comprehensively presented through extensive simulations.