Abstract: A proton exchange membrane has been developed for
direct methanol fuel cell (DMFC). The nanofiber network composite
membranes were prepared by interconnected network of Nafion
(perfuorosulfonic acid) nanofibers that have been embedded in an
uncharged and inert polymer matrix, by electro-spinning. The
spinning solution of Nafion with a low concentration (1 wt%
compared to Nafion) of high molecular weight poly(ethylene oxide),
as a carrier polymer. The interconnected network of Nafion
nanofibers with average fiber diameter in the range of 160-700nm,
were used to make the membranes, with the nanofiber occupying up
to 85% of the membrane volume. The matrix polymer was
crosslinked with Norland Optical Adhesive 63 under UV. The
resulting membranes showed proton conductivity of 0.10 S/cm at
25°C and 80% RH; and methanol permeability of 3.6 x 10-6 cm2/s.
Abstract: This research investigated the properties of
Rhizophora charcoal for product design on 3 aspects: electrical
conductor, impurity absorption, and fresh fruit shelf life. After the
study, the properties of Rhizophora charcoal were applied to produce
local product model at Ban Yisarn, Ampawa District,
Samudsongkram Province which can add value to the Rhizophora
charcoal as one of the OTOP (One-Tambon-One product). The
results showed that the Rhizophora charcoal is not an electrical
conductor but good liquid impurity absorber and it can extend fresh
fruit shelf life.
Abstract: The objective of this research is to use Rhizophora wood to design a walking stick for elderly. The research was conducted by studying the behavior and the type of walking sticks used by 70 elderly aged between 60-80 years in Pragnamdaeng Sub-District, Samudsongkram Province. Questionnaires were used to collect data which were calculated to find percentage, mean, and standard deviation. The results are as follows: 1) most elderly use walking sticks due to the Osteoarthritis of the knees. 2) Most elderly need to use walking sticks because the walking sticks help to balance their positioning and prevent from stumble. 3) Most elderly agree that Rhizophora wood is suitable to make a walking stick because of its strength and toughness. 4) The design of the walking stick should be fine and practical with comfortable handle and the tip of the stick must not be slippery.
Abstract: The objectives of this research were to design and develop foot massage plate from coconut shell. The research investigated on the satisfaction of the users on the developed foot massage plate on 4 aspects; usage, practical in use, safety, and materials & production process. The sample group included 64 people joining the service at Wat Paitan Health Center, Bangkok. The samples were randomly tried on the massage plate and evaluated according to the 4 aspects. The data were analyzed to find mean, percentage, and standard deviation. The result showed that the overall satisfaction was at good level (mean = 3.80). When considering in details, it was found that the subjects reported their highest satisfaction on the practical usage (mean = 4.16), followed by safety (mean = 3.82); then, materials and production process (mean = 3.78). The least satisfaction aspect was on function and usage (mean = 3.45) or moderate level.
Abstract: Malaria constitutes one of the major health problems
in Nigeria. One of the reasons attributed for the upsurge was the
development of resistance of Plasmodium falciparum and the
emergence of multi-resistant strains of the parasite to anti-malaria
drugs. A continued search for other effective, safe and cheap plantbased
anti-malaria agents thus becomes imperative in the face of
these difficulties. The objective of this study is therefore to evaluate
the in vivo anti-malarial efficacy of ethanolic extracts of
Chromolaena odorata and Androgaphis paniculata leaves. The two
plants were evaluated for their anti-malaria efficacy in vivo in a 4-day
curative test assay against Plasmodium berghei strain in mice. The
group treated with 500mg/ml dose of ethanolic extract of A.
paniculata plant showed parasite suppression with increase in Packed
Cell Volume (PCV) value except day 3 which showed a slight
decrease in PCV value. During the 4-day curative test, an increase in
the PCV values, weight measurement and zero count of Plasmodium
berghei parasite values was recorded after day 3 of drug
administration. These results obtained in group treated with A.
paniculata extract showed anti-malarial efficacy with higher
mortality rate in parasitaemia count when compared with
Chromolaena odorata group. These results justify the use of
ethanolic extracts of A. paniculata plant as medicinal herb used in
folklore medicine in the treatment of malaria.
Abstract: The volatile organic compounds - BTEX (Benzene, Toluene, Ethylbenzene, and Xylene) petroleum derivatives, have high rates of toxicity, which may carry consequences for human health, biota and environment. In this directon, this paper proposes a method of treatment of these compounds by using corona discharge plasma technology. The efficiency of the method was tested by analyzing samples of BTEX after going through a plasma reactor by gas chromatography method. The results show that the optimal residence time of the sample in the reactor was 8 minutes.
Abstract: In recent years, thanks to the development of information and communication technologies, the computer and internet have been used widely in higher education. Internet-based education is impacting traditional higher education as online components increasingly become integrated into face- to- face (FTF) courses. The goal of combined internet-based and traditional education is to take full advantage of the benefits of each platform in order to provide an educational opportunity that can promote student learning better than can either platform alone. Research results show that the use of hybrid learning is more effective than online or FTF models in higher education. Due to the potential benefits, an increasing number of institutions are interested in developing hybrid courses, programs, and degrees. Future research should evaluate the effectiveness of hybrid learning. This paper is designed to determine the impact of hybrid learning on higher education.
Abstract: Energy is required in almost every aspect of human activities and development of any nation in the world. Increasing fossil fuel price, energy security and climate change have important bearings on sustainable development of any nation. The renewable energy technology is considered one of the drastic approaches which taken over the world to reduce the energy problem. The preservation of vegetables by freezing is one of the most important methods of retaining quality in agricultural products over long-term storage periods. Freezing factories show high demand of energy for both heat and electricity; the hybrid Photovoltaic/Thermal (PV/T) systems could be used in order to meet this requirement. This paper presents PV/T system design for freezing factory. Also, the complete mathematical modeling and MATLAB SIMULINK of PV/T collector is introduced. The sensitivity analysis for the manufacturing parameters of PV/T collector is carried out to study their effect on both thermal and electrical efficiency.
Abstract: In this paper, the optimum design for renewable energy system powered an aquaculture pond was determined. Hybrid Optimization Model for Electric Renewable (HOMER) software program, which is developed by U.S National Renewable Energy Laboratory (NREL), is used for analyzing the feasibility of the stand alone and hybrid system in this study. HOMER program determines whether renewable energy resources satisfy hourly electric demand or not. The program calculates energy balance for every 8760 hours in a year to simulate operation of the system. This optimization compares the demand for the electrical energy for each hour of the year with the energy supplied by the system for that hour and calculates the relevant energy flow for each component in the model. The essential principle is to minimize the total system cost while HOMER ensures control of the system. Moreover the feasibility analysis of the energy system is also studied. Wind speed, solar irradiance, interest rate and capacity shortage are the parameters which are taken into consideration. The simulation results indicate that the hybrid system is the best choice in this study, yielding lower net present cost. Thus, it provides higher system performance than PV or wind stand alone systems.
Abstract: Recently, the use of web 2.0 tools has increased in
companies and public administration organisations. This
phenomenon, known as "Enterprise 2.0", has, de facto, modified
common organisational and operative practices. This has led
“knowledge workers” to change their working practices through the
use of Web 2.0 communication tools. Unfortunately, these tools have
not been integrated with existing enterprise information systems, a
situation that could potentially lead to a loss of information. This is
an important problem in an organisational context, because
knowledge of information exchanged within the organisation is
needed to increase the efficiency and competitiveness of the
organisation. In this article we demonstrate that it is possible to
capture this knowledge using collaboration processes, which are
processes of abstraction created in accordance with design patterns
and applied to new organisational operative practices.
Abstract: Montmorillonite (MMT) is a very abundant clay mineral and is versatile such that it can be chemically or physically altered by changing the ions between the sheets of its layered structure. This clay mineral can be prepared into functional nanoparticles that can be used as fillers in other nanomaterials such as nanofibers to achieve special properties. In this study, two types of iron-modified MMT, Iron-MMT (FeMMT) and Zero Valent Iron-MMT (ZVIMMT) were synthesized via ion exchange technique. The modified clay was incorporated in polymer nanofibers which were produced using a process called electrospinning. ICP analysis confirmed that clay modification was successful where there is an observed decrease in the concentration of Na and an increase in the concentration of Fe after ion exchange. XRD analysis also confirmed that modification took place because of the changes in the d-spacing of Na-MMT from 11.5 Å to 13.6 Å and 12.6 Å after synthesis of FeMMT and ZVIMMT, respectively. SEM images of the electrospun nanofibers revealed that the ZVIMMT-filled fibers have a smaller average diameter than the FeMMT-filled fibers because of the lower resistance of the suspensions of the former to the elongation force from the applied electric field. The resistance to the electric field was measured by getting the bulk voltage of the suspensions.
Abstract: 12.7-mm thick plates of 6061-T6511 aluminum alloy and high hardness steel (528 HV) were successfully joined by a friction stir bonding process using a tungsten-rhenium stir tool. Process parameter variation experiments, which included tool design geometry, plunge and traverse rates, tool offset, spindle tilt, and rotation speed, were conducted to develop a parameter set which yielded a defect free joint. Laboratory tensile tests exhibited yield stresses which exceed the strengths of comparable AA6061-to-AA6061 fusion and friction stir weld joints. Scanning electron microscopy and energy dispersive X-ray spectroscopy analysis also show atomic diffusion at the material interface region.
Abstract: In the paper environmental impact analysis the optimal Diesel engine for a light helicopter was performed. The paper consist an answer to the question of what the optimal Diesel engine for a light helicopter is, taking into consideration its expected performance and design capacity. The use of turbocharged engine with self-ignition and an electronic control system can substantially reduce the negative impact on the environment by decreasing toxic substance emission, fuel consumption and therefore carbon dioxide emission. In order to establish the environmental benefits of the diesel engine technologies, mathematical models were created, providing additional insight on the environmental impact and performance of a classic turboshaft and an advanced diesel engine light helicopter, incorporating technology developments.
Abstract: This paper describes a cycle accurate simulation results of weight values learned by an auto-encoder behavior model in terms of pre-route simulation. Given the results we visualized the first layer representations with natural images. Many common deep learning threads have focused on learning high-level abstraction of unlabeled raw data by unsupervised feature learning. However, in the process of handling such a huge amount of data, the learning method’s computation complexity and time limited advanced research. These limitations came from the fact these algorithms were computed by using only single core CPUs. For this reason, parallel-based hardware, FPGAs, was seen as a possible solution to overcome these limitations. We adopted and simulated the ready-made auto-encoder to design a behavior model in VerilogHDL before designing hardware. With the auto-encoder behavior model pre-route simulation, we obtained the cycle accurate results of the parameter of each hidden layer by using MODELSIM. The cycle accurate results are very important factor in designing a parallel-based digital hardware. Finally this paper shows an appropriate operation of behavior model based pre-route simulation. Moreover, we visualized learning latent representations of the first hidden layer with Kyoto natural image dataset.
Abstract: This study presents the optimal design and formulation of a kinematic model of a flexible slider crank mechanism. The objective of the proposed innovative design is to take extra advantage of the compliant mechanism and maximize the fatigue life by applying the Taguchi method. A formulated kinematic model is developed using a pseudo-rigid-body model (PRBM). By means of mathematic models, the kinematic behaviors of the flexible slider crank mechanism are captured using MATLAB software. Finite element analysis (FEA) is used to show the stress distribution. The results show that the optimal shape of the flexible hinge includes a force of 8.5N, a width of 9mm and a thickness of 1.1mm. Analysis of variance shows that the thickness of the proposed hinge is the most significant parameter, with an F test of 15.5. Finally, a prototype is manufactured to prepare for testing the kinematic and dynamic behaviors.
Abstract: Complex sensitivity analysis of stresses in a concrete slab of the real type of rigid pavement made from recycled materials is performed. The computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method that respects the structural nonlinearity, enables to model different arrangements of joints, and the entire model can be loaded by the thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with the help of special contact elements. Four concrete slabs separated by transverse and longitudinal joints and the additional structural layers and soil to the depth of about 3m are modeled. The thickness of individual layers, physical and mechanical properties of materials, characteristics of joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique Updated Latin Hypercube Sampling with 20 simulations is used. For sensitivity analysis the sensitivity coefficient based on the Spearman rank correlation coefficient is utilized. As a result, the estimates of influence of random variability of individual input variables on the random variability of principal stresses s1 and s3 in 53 points on the upper and lower surface of the concrete slabs are obtained.
Abstract: Speed, power consumption and area, are some of the most important factors of concern in modern day memory design. As we move towards Deep Sub-Micron Technologies, the problems of leakage current, noise and cell stability due to physical parameter variation becomes more pronounced. In this paper we have designed an 8T Read Decoupled Dual Port SRAM Cell with Dual Threshold Voltage and characterized it in terms of read and write delay, read and write noise margins, Data Retention Voltage and Leakage Current. Read Decoupling improves the Read Noise Margin and static power dissipation is reduced by using Dual-Vt transistors. The results obtained are compared with existing 6T, 8T, 9T SRAM Cells, which shows the superiority of the proposed design. The Cell is designed and simulated in TSPICE using 90nm CMOS process.
Abstract: The more homogenized population taken over by the Republic immediately after the Ottoman was being canalized towards the goal of national identity and the historical and cultural structure of the nation was being readdressed and redefined. Modernization and Westernization history of the new Turkey, which started with Ottoman reforms and took its final form with the Kemalist nation-state, politically resulted in transformation from a multinational empire to a “nation-state” and adopted reaching to the level of Western civilizations as a sociology ideal. This objective of change will be achieved, on the one hand, by finding the Turkish culture which was preserved only by the society and by instilling Western civilization to national culture, on the other hand. In line with this, it is seen that in musical considerations while Turkish folk music was accepted and adopted as an indispensible part of Turkish identity, Turkish classical music was refused on the ground that it was not a part of Turkish identity. Again in this period, it is seen that with the notion of cultural reform, which is a part of “nation building”, the desire to create a national music to be performed with Western techniques brought along deliberate interventions to folk music.
Abstract: Two multisensor system architectures for navigation
and guidance of small Unmanned Aircraft (UA) are presented and
compared. The main objective of our research is to design a compact,
light and relatively inexpensive system capable of providing the
required navigation performance in all phases of flight of small UA,
with a special focus on precision approach and landing, where Vision
Based Navigation (VBN) techniques can be fully exploited in a
multisensor integrated architecture. Various existing techniques for
VBN are compared and the Appearance-Based Navigation (ABN)
approach is selected for implementation. Feature extraction and
optical flow techniques are employed to estimate flight parameters
such as roll angle, pitch angle, deviation from the runway centreline
and body rates. Additionally, we address the possible synergies of
VBN, Global Navigation Satellite System (GNSS) and MEMS-IMU
(Micro-Electromechanical System Inertial Measurement Unit)
sensors, and the use of Aircraft Dynamics Model (ADM) to provide
additional information suitable to compensate for the shortcomings of
VBN and MEMS-IMU sensors in high-dynamics attitude
determination tasks. An Extended Kalman Filter (EKF) is developed
to fuse the information provided by the different sensors and to
provide estimates of position, velocity and attitude of the UA
platform in real-time. The key mathematical models describing the
two architectures i.e., VBN-IMU-GNSS (VIG) system and VIGADM
(VIGA) system are introduced. The first architecture uses VBN
and GNSS to augment the MEMS-IMU. The second mode also
includes the ADM to provide augmentation of the attitude channel.
Simulation of these two modes is carried out and the performances of
the two schemes are compared in a small UA integration scheme (i.e.,
AEROSONDE UA platform) exploring a representative cross-section
of this UA operational flight envelope, including high dynamics
manoeuvres and CAT-I to CAT-III precision approach tasks.
Simulation of the first system architecture (i.e., VIG system) shows
that the integrated system can reach position, velocity and attitude
accuracies compatible with the Required Navigation Performance
(RNP) requirements. Simulation of the VIGA system also shows
promising results since the achieved attitude accuracy is higher using
the VBN-IMU-ADM than using VBN-IMU only. A comparison of
VIG and VIGA system is also performed and it shows that the
position and attitude accuracy of the proposed VIG and VIGA
systems are both compatible with the RNP specified in the various
UA flight phases, including precision approach down to CAT-II.
Abstract: This paper deals with the direct torque control (DTC) of the induction motor. This type of control allows decoupling control between the flux and the torque without the need for a transformation of coordinates. However, as with other hysteresis-based systems, the classical DTC scheme represents a high ripple, in both the electromagnetic torque and the stator flux and a distortion in the stator current. As well, it suffers from variable switching frequency. To solve these problems various modifications, in conventional DTC scheme, have been made during the last decade. Indeed the DTC based on space vector modulation (SVM) has proved to generate very low ripples in torque and flux with constant switching frequency. It also shows almost the same dynamic performances as the classical DTC system. On the other hand, fuzzy logic is considered as an interesting alternative approach for its advantages: Analysis close to the exigencies of user, ability of nonlinear systems control, best dynamic performances and inherent quality of robustness.
Therefore, two fuzzy direct torque control approaches, for the induction motor fed by SVM-voltage source inverter, are proposed in this paper. By using these two approaches of DTC, the advantages of fuzzy logic control, space vector modulation, and direct torque control method are combined. The performances of these DTC schemes are evaluated through digital simulation using Matlab/Simulink platform and fuzzy logic tools. Simulation results illustrate the effectiveness and the superiority of the proposed Fuzzy DTC-SVM schemes in comparison to the classical DTC.