Abstract: This paper presents a compact thermoelectric power generator system based on temperature difference across the element. The system can transfer the burning heat energy to electric energy directly. The proposed system has a thermoelectric generator and a power control box. In the generator, there are 4 thermoelectric modules (TEMs), each of which uses 2 thermoelectric chips (TEs) and 2 cold sinks, 1 thermal absorber, and 1 thermal conduction flat board. In the power control box, there are 1 storing energy device, 1 converter, and 1 inverter. The total net generating power is about 11W. This system uses commercial portable gas stoves or burns timber or the coal as the heat source, which is easily obtained. It adopts solid-state thermoelectric chips as heat inverter parts. The system has the advantages of being light-weight, quite, and mobile, requiring no maintenance, and havng easily-supplied heat source. The system can be used a as long as burning is allowed. This system works well for highly-mobilized outdoors situations by providing a power for illumination, entertainment equipment or the wireless equipment at refuge. Under heavy storms such as typhoon, when the solar panels become ineffective and the wind-powered machines malfunction, the thermoelectric power generator can continue providing the vital power.
Abstract: Blood pulse is an important human physiological signal commonly used for the understanding of the individual physical health. Current methods of non-invasive blood pulse sensing require direct contact or access to the human skin. As such, the performances of these devices tend to vary with time and are subjective to human body fluids (e.g. blood, perspiration and skin-oil) and environmental contaminants (e.g. mud, water, etc). This paper proposes a simulation model for the novel method of non-invasive acquisition of blood pulse using the disturbance created by blood flowing through a localized magnetic field. The simulation model geometry represents a blood vessel, a permanent magnet, a magnetic sensor, surrounding tissues and air in 2-dimensional. In this model, the velocity and pressure fields in the blood stream are described based on Navier-Stroke equations and the walls of the blood vessel are assumed to have no-slip condition. The blood assumes a parabolic profile considering a laminar flow for blood in major artery near the skin. And the inlet velocity follows a sinusoidal equation. This will allow the computational software to compute the interactions between the magnetic vector potential generated by the permanent magnet and the magnetic nanoparticles in the blood. These interactions are simulated based on Maxwell equations at the location where the magnetic sensor is placed. The simulated magnetic field at the sensor location is found to assume similar sinusoidal waveform characteristics as the inlet velocity of the blood. The amplitude of the simulated waveforms at the sensor location are compared with physical measurements on human subjects and found to be highly correlated.
Abstract: The objective of this paper is to estimate realistic
principal extrusion process parameters by means of artificial neural
network. Conventionally, finite element analysis is used to derive
process parameters. However, the finite element analysis of the
extrusion model does not consider the manufacturing process
constraints in its modeling. Therefore, the process parameters
obtained through such an analysis remains highly theoretical.
Alternatively, process development in industrial extrusion is to a
great extent based on trial and error and often involves full-size
experiments, which are both expensive and time-consuming. The
artificial neural network-based estimation of the extrusion process
parameters prior to plant execution helps to make the actual extrusion
operation more efficient because more realistic parameters may be
obtained. And so, it bridges the gap between simulation and real
manufacturing execution system. In this work, a suitable neural
network is designed which is trained using an appropriate learning
algorithm. The network so trained is used to predict the
manufacturing process parameters.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: The design of a modern aircraft is based on three pillars: theoretical results, experimental test and computational simulations.
As a results of this, Computational Fluid Dynamic (CFD) solvers are
widely used in the aeronautical field. These solvers require the correct
selection of many parameters in order to obtain successful results. Besides, the computational time spent in the simulation depends on
the proper choice of these parameters.
In this paper we create an expert system capable of making an
accurate prediction of the number of iterations and time required for the convergence of a computational fluid dynamic (CFD) solver.
Artificial neural network (ANN) has been used to design the expert system. It is shown that the developed expert system is capable of making an accurate prediction the number of iterations and time
required for the convergence of a CFD solver.
Abstract: Software estimation accuracy is among the greatest
challenges for software developers. This study aimed at building and
evaluating a neuro-fuzzy model to estimate software projects
development time. The forty-one modules developed from ten
programs were used as dataset. Our proposed approach is compared
with fuzzy logic and neural network model and Results show that the
value of MMRE (Mean of Magnitude of Relative Error) applying
neuro-fuzzy was substantially lower than MMRE applying fuzzy
logic and neural network.
Abstract: The authors present an algorithm for order reduction of linear dynamic systems using the combined advantages of stability equation method and the error minimization by Genetic algorithm. The denominator of the reduced order model is obtained by the stability equation method and the numerator terms of the lower order transfer function are determined by minimizing the integral square error between the transient responses of original and reduced order models using Genetic algorithm. The reduction procedure is simple and computer oriented. It is shown that the algorithm has several advantages, e.g. the reduced order models retain the steady-state value and stability of the original system. The proposed algorithm has also been extended for the order reduction of linear multivariable systems. Two numerical examples are solved to illustrate the superiority of the algorithm over some existing ones including one example of multivariable system.
Abstract: Conventionally the selection of parameters depends
intensely on the operator-s experience or conservative technological
data provided by the EDM equipment manufacturers that assign
inconsistent machining performance. The parameter settings given by
the manufacturers are only relevant with common steel grades. A
single parameter change influences the process in a complex way.
Hence, the present research proposes artificial neural network (ANN)
models for the prediction of surface roughness on first commenced
Ti-15-3 alloy in electrical discharge machining (EDM) process. The
proposed models use peak current, pulse on time, pulse off time and
servo voltage as input parameters. Multilayer perceptron (MLP) with
three hidden layer feedforward networks are applied. An assessment
is carried out with the models of distinct hidden layer. Training of the
models is performed with data from an extensive series of
experiments utilizing copper electrode as positive polarity. The
predictions based on the above developed models have been verified
with another set of experiments and are found to be in good
agreement with the experimental results. Beside this they can be
exercised as precious tools for the process planning for EDM.
Abstract: The paper proposes an approach using genetic algorithm for computing the region based image similarity. The image is denoted using a set of segmented regions reflecting color and texture properties of an image. An image is associated with a family of image features corresponding to the regions. The resemblance of two images is then defined as the overall similarity between two families of image features, and quantified by a similarity measure, which integrates properties of all the regions in the images. A genetic algorithm is applied to decide the most plausible matching. The performance of the proposed method is illustrated using examples from an image database of general-purpose images, and is shown to produce good results.
Abstract: In this paper we compare the response of linear and
nonlinear neural network-based prediction schemes in prediction of
received Signal-to-Interference Power Ratio (SIR) in Direct
Sequence Code Division Multiple Access (DS/CDMA) systems. The
nonlinear predictor is Multilayer Perceptron MLP and the linear
predictor is an Adaptive Linear (Adaline) predictor. We solve the
problem of complexity by using the Minimum Mean Squared Error
(MMSE) principle to select the optimal predictors. The optimized
Adaline predictor is compared to optimized MLP by employing
noisy Rayleigh fading signals with 1.8 GHZ carrier frequency in an
urban environment. The results show that the Adaline predictor can
estimates SIR with the same error as MLP when the user has the
velocity of 5 km/h and 60 km/h but by increasing the velocity up-to
120 km/h the mean squared error of MLP is two times more than
Adaline predictor. This makes the Adaline predictor (with lower
complexity) more suitable than MLP for closed-loop power control
where efficient and accurate identification of the time-varying
inverse dynamics of the multi path fading channel is required.
Abstract: Reconfigurable optical add/drop multiplexers
(ROADMs) can be classified into three categories based on their
underlying switching technologies. Category I consists of a single
large optical switch; category II is composed of a number of small
optical switches aligned in parallel; and category III has a single
optical switch and only one wavelength being added/dropped. In this
paper, to evaluate the wavelength-routing capability of ROADMs of
category-II in dynamic optical networks,the dynamic traffic models
are designed based on Bernoulli, Poisson distributions for smooth
and regular types of traffic. Through Analytical and Simulation
results, the routing power of cat-II of ROADM networks for two
traffic models are determined.
Abstract: In this paper back-propagation artificial neural network
(BPANN) is employed to predict the deformation of the upsetting
process. To prepare a training set for BPANN, some finite element
simulations were carried out. The input data for the artificial neural
network are a set of parameters generated randomly (aspect ratio d/h,
material properties, temperature and coefficient of friction). The
output data are the coefficient of polynomial that fitted on barreling
curves. Neural network was trained using barreling curves generated
by finite element simulations of the upsetting and the corresponding
material parameters. This technique was tested for three different
specimens and can be successfully employed to predict the
deformation of the upsetting process
Abstract: In this paper, we proposed a new routing protocol for
Unmanned Aerial Vehicles (UAVs) that equipped with directional
antenna. We named this protocol Directional Optimized Link State
Routing Protocol (DOLSR). This protocol is based on the well
known protocol that is called Optimized Link State Routing Protocol
(OLSR). We focused in our protocol on the multipoint relay (MPR)
concept which is the most important feature of this protocol. We
developed a heuristic that allows DOLSR protocol to minimize
the number of the multipoint relays. With this new protocol the
number of overhead packets will be reduced and the End-to-End
delay of the network will also be minimized. We showed through
simulation that our protocol outperformed Optimized Link State
Routing Protocol, Dynamic Source Routing (DSR) protocol and Ad-
Hoc On demand Distance Vector (AODV) routing protocol in
reducing the End-to-End delay and enhancing the overall
throughput. Our evaluation of the previous protocols was based
on the OPNET network simulation tool.
Abstract: Heterogeneity of solid waste characteristics as well as the complex processes taking place within the landfill ecosystem motivated the implementation of soft computing methodologies such as artificial neural networks (ANN), fuzzy logic (FL), and their combination. The present work uses a hybrid ANN-FL model that employs knowledge-based FL to describe the process qualitatively and implements the learning algorithm of ANN to optimize model parameters. The model was developed to simulate and predict the landfill gas production at a given time based on operational parameters. The experimental data used were compiled from lab-scale experiment that involved various operating scenarios. The developed model was validated and statistically analyzed using F-test, linear regression between actual and predicted data, and mean squared error measures. Overall, the simulated landfill gas production rates demonstrated reasonable agreement with actual data. The discussion focused on the effect of the size of training datasets and number of training epochs.
Abstract: In this paper we designed and implemented a new
ensemble of classifiers based on a sequence of classifiers which were
specialized in regions of the training dataset where errors of its
trained homologous are concentrated. In order to separate this
regions, and to determine the aptitude of each classifier to properly
respond to a new case, it was used another set of classifiers built
hierarchically. We explored a selection based variant to combine the
base classifiers. We validated this model with different base
classifiers using 37 training datasets. It was carried out a statistical
comparison of these models with the well known Bagging and
Boosting, obtaining significantly superior results with the
hierarchical ensemble using Multilayer Perceptron as base classifier.
Therefore, we demonstrated the efficacy of the proposed ensemble,
as well as its applicability to general problems.
Abstract: The inherent iterative nature of product design and development poses significant challenge to reduce the product design and development time (PD). In order to shorten the time to market, organizations have adopted concurrent development where multiple specialized tasks and design activities are carried out in parallel. Iterative nature of work coupled with the overlap of activities can result in unpredictable time to completion and significant rework. Many of the products have missed the time to market window due to unanticipated or rather unplanned iteration and rework. The iterative and often overlapped processes introduce greater amounts of ambiguity in design and development, where the traditional methods and tools of project management provide less value. In this context, identifying critical metrics to understand the iteration probability is an open research area where significant contribution can be made given that iteration has been the key driver of cost and schedule risk in PD projects. Two important questions that the proposed study attempts to address are: Can we predict and identify the number of iterations in a product development flow? Can we provide managerial insights for a better control over iteration? The proposal introduces the concept of decision points and using this concept intends to develop metrics that can provide managerial insights into iteration predictability. By characterizing the product development flow as a network of decision points, the proposed research intends to delve further into iteration probability and attempts to provide more clarity.
Abstract: In cancer progress, the optical properties of tissues
like absorption and scattering coefficient change, so by these
changes, we can trace the progress of cancer, even it can be applied
for pre-detection of cancer. In this paper, we investigate the effects of
changes of optical properties on light penetrated into tissues. The
diffusion equation is widely used to simulate light propagation into
biological tissues. In this study, the boundary integral method (BIM)
is used to solve the diffusion equation. We illustrate that the changes
of optical properties can modified the reflectance or penetrating light.
Abstract: In the paper the mathematical model of tumor
growth is considered. New capillary network formation,
which supply cancer cells with the nutrients, is taken into the
account. A formula estimating a tumor growth in connection
with the number of capillaries is obtained.
Abstract: The development of Web has affected different aspects of our lives, such as communication, sharing knowledge, searching for jobs, social activities, etc. The web portal as a gateway in the World Wide Web is a starting point for people who are connecting to the Internet. The web portal as the type of knowledge management system provides a rich space to share and search information as well as communication services like free email or content provision for the users. This research aims to discover the university needs to the web portal as a necessary tool for students in the universities to help them in getting the required information. A survey was conducted to gather students' requirements which can be incorporated in to portal to be developed.
Abstract: The present study focuses on the discussion over the
parameter of Artificial Neural Network (ANN). Sensitivity analysis is
applied to assess the effect of the parameters of ANN on the prediction
of turbidity of raw water in the water treatment plant. The result shows
that transfer function of hidden layer is a critical parameter of ANN.
When the transfer function changes, the reliability of prediction of
water turbidity is greatly different. Moreover, the estimated water
turbidity is less sensitive to training times and learning velocity than
the number of neurons in the hidden layer. Therefore, it is important to
select an appropriate transfer function and suitable number of neurons
in the hidden layer in the process of parameter training and validation.