Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: The design of Reverse logistics Network has attracted
growing attention with the stringent pressures from both
environmental awareness and business sustainability. Reverse
logistical activities include return, remanufacture, disassemble and
dispose of products can be quite complex to manage. In addition,
demand can be difficult to predict, and decision making is one of the
challenges task in such network. This complexity has amplified the
need to develop an integrated architecture for product return as an
enterprise system. The main purpose of this paper is to design Multi
Agent System (MAS) architecture using the Prometheus
methodology to efficiently manage reverse logistics processes. The
proposed MAS architecture includes five types of agents: Gate
keeping Agent, Collection Agent, Sorting Agent, Processing Agent
and Disposal Agent which act respectively during the five steps of
reverse logistics Network.
Abstract: This paper introduces a boost converter with a new
active snubber cell. In this circuit, all of the semiconductor
components in the converter softly turns on and turns off with the
help of the active snubber cell. Compared to the other converters, the
proposed converter has advantages of size, number of components
and cost. The main feature of proposed converter is that the extra
voltage stresses do not occur on the main switches and main diodes.
Also, the current stress on the main switch is acceptable level.
Moreover, the proposed converter can operates under light load
conditions and wide input line voltage. In this study, the operating
principle of the proposed converter is presented and its operation is
verified with the Proteus simulation software for a 1 kW and 100 kHz
model.
Abstract: This article presents a vibration diagnostic method
designed for Permanent Magnets (PM) electrical machines–traction
motors and generators. Those machines are commonly used in traction
drives of electrical vehicles and small wind or water systems. The
described method is very innovative and unique. Specific structural
properties of machines excited by permanent magnets are used in this
method - electromotive force (EMF) generated due to vibrations. There
was analyzed number of publications, which describe vibration
diagnostic methods, and tests of electrical machines and there was no
method found to determine the technical condition of such machine
basing on their own signals. This work presents field-circuit model,
results of static tests, results of calculations and simulations.
Abstract: Currently, green rating systems are mainly utilized for
correctly sizing mechanical and electrical systems, which have short
lifetime expectancies. In these systems, passive solar and bio-climatic
architecture, which have long lifetime expectancies, are neglected.
Urban rating systems consider buildings and services in addition to
neighborhoods and public transportation as integral parts of the built
environment. The main goal of this study was to develop a more
consistent point allocation system for urban building standards by
using six different lifetime shearing layers: Site, Structure, Skin,
Services, Space, and Stuff, each reflecting distinct environmental
damages. This shearing-layer concept was applied to internationally
well-known rating systems: Leadership in Energy and Environmental
Design (LEED) for Neighborhood Development, BRE
Environmental Assessment Method (BREEAM) for Communities
and Comprehensive Assessment System for Building Environmental
Efficiency (CASBEE) for Urban Development. The results showed
that LEED for Neighborhood Development and BREEAM for
Communities focused on long-lifetime-expectancy building designs,
whereas CASBEE for Urban Development gave equal importance to
the Building and Service Layers. Moreover, although this rating
system was applied using a building-scale assessment, “Urban Area +
Buildings” focuses on a short-lifetime-expectancy system design,
neglecting to improve the architectural design by considering bioclimatic
and passive solar aspects.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Nowadays, several research studies point up that an
active lifestyle is essential for physical and mental health benefits.
Mobile phones have greatly influenced people’s habits and attitudes
also in the way they exercise. Our research work is mainly focused on
investigating how to exploit mobile technologies to favour people’s
exertion experience. To this end, we developed an exertion framework
users can exploit through a real world mobile application, called
EverywhereSport Run (EWRun), designed to act as a virtual personal
trainer to support runners during their trainings. In this work, inspired
by both previous findings in the field of interaction design for people
with visual impairments, feedback gathered from real users of our
framework, and positive results obtained from two experimentations,
we present some new interaction facilities we designed to enhance
the interaction experience during a training. The positive obtained
results helped us to derive some interaction design recommendations
we believe will be a valid support for designers of future mobile
systems conceived to be used in circumstances where there are limited
possibilities of interaction.
Abstract: Mobile Adhoc Networks (MANETs) are
infrastructure-less, dynamic network of collections of wireless mobile
nodes communicating with each other without any centralized
authority. A MANET is a mobile device of interconnections through
wireless links, forming a dynamic topology. Routing protocols have a
big role in data transmission across a network. Routing protocols,
two major classifications are unipath and multipath. This study
evaluates performance of an on-demand multipath routing protocol
named Adhoc On-demand Multipath Distance Vector routing
(AOMDV). This study proposes Energy Aware AOMDV (EAAOMDV)
an extension of AOMDV which decreases energy
consumed on a route.
Abstract: Based on application requirements, nodes are static or
mobile in Wireless Sensor Networks (WSNs). Mobility poses
challenges in protocol design, especially at the link layer requiring
mobility adaptation algorithms to localize mobile nodes and predict
link quality to be established with them. This study implements
XMAC and Berkeley Media Access Control (BMAC) routing
protocols to evaluate performance under WSN’s static and mobility
conditions. This paper gives a comparative study of mobility-aware
MAC protocols. Routing protocol performance, based on Average
End to End Delay, Average Packet Delivery Ratio, Average Number
of hops, and Jitter is evaluated.
Abstract: To tackle the air pollution issues, Plug-in Hybrid
Electric Vehicles (PHEVs) are proposed as an appropriate solution.
Charging a large amount of PHEV batteries, if not controlled, would
have negative impacts on the distribution system. The control process
of charging of these vehicles can be centralized in parking lots that
may provide a chance for better coordination than the individual
charging in houses. In this paper, an optimization-based approach is
proposed to determine the optimum PHEV parking capacities in
candidate nodes of the distribution system. In so doing, a profile for
charging and discharging of PHEVs is developed in order to flatten
the network load profile. Then, this profile is used in solving an
optimization problem to minimize the distribution system losses. The
outputs of the proposed method are the proper place for PHEV
parking lots and optimum capacity for each parking. The application
of the proposed method on the IEEE-34 node test feeder verifies the
effectiveness of the method.
Abstract: Application of biochar to arable soils represents a new
approach to restore soil health and quality. Many studies reported the
positive effect of biochar application on soil fertility and
development of soil microbial community. Moreover biochar may
affect the soil water retention, but this effect has not been sufficiently
described yet. Therefore this study deals with the influence of
biochar application on: microbial activities in soil, availability of
mineral nitrogen in soil for microorganisms, mineral nitrogen
retention and plant production. To demonstrate the effect of biochar
addition on the above parameters, the pot experiment was realized.
As a model crop, Lactuca sativa L. was used and cultivated from
December 10th 2014 till March 22th 2015 in climate chamber in
thoroughly homogenized arable soil with and without addition of
biochar. Five variants of experiment (V1 – V5) with different regime
of irrigation were prepared. Variants V1 – V2 were fertilized by
mineral nitrogen, V3 – V4 by biochar and V5 was a control. The
significant differences were found only in plant production and
mineral nitrogen retention. The highest content of mineral nitrogen
in soil was detected in V1 and V2, about 250 % in comparison with
the other variants. The positive effect of biochar application on soil
fertility, mineral nitrogen availability was not found. On the other
hand results of plant production indicate the possible positive effect
of biochar application on soil water retention.
Abstract: In order to study the effect of different levels of triple
super phosphate chemical fertilizer and biological phosphate fertilizer
(fertile 2) on some morphological traits of corn this research was
carried out in Ahvaz in 2002 as a factorial experiment in randomized
complete block design with 4 replications). The experiment included
two factors: first, biological phosphate fertilizer (fertile 2) at three
levels of 0, 100, 200 g/ha; second, triple super phosphate chemical
fertilizer at three levels of 0, 60, 90 kg/ha of pure phosphorus (P2O5).
The obtained results indicated that fertilizer treatments had a
significant effect on some morphological traits at 1% probability
level. In this regard, P2B2 treatment (100 g/ha biological phosphate
fertilizer (fertile 2) and 60 kg/ha triple super phosphate fertilizer) had
the greatest plant height, stem diameter, number of leaves and ear
length. It seems that in Ahvaz weather conditions, decrease of
consumption of triple superphosphate chemical fertilizer to less than
a half along with the consumption of biological phosphate fertilizer
(fertile 2) is highly important in order to achieve optimal results.
Therefore, it can be concluded that biological fertilizers can be used
as a suitable substitute for some of the chemical fertilizers in
sustainable agricultural systems.
Abstract: An experimental investigation is carried out to
establish the performance characteristics of a compression ignition
engine while using cerium oxide nanoparticles as additive in neat
diesel and diesel-biodiesel blends. In the first phase of the
experiments, stability of neat diesel and diesel-biodiesel fuel blends
with the addition of cerium oxide nanoparticles is analyzed. After
series of experiments, it is found that the blends subjected to high
speed blending followed by ultrasonic bath stabilization improves the
stability. In the second phase, performance characteristics are studied
using the stable fuel blends in a single cylinder four stroke engine
coupled with an electrical dynamometer and a data acquisition
system. The cerium oxide acts as an oxygen donating catalyst and
provides oxygen for combustion. The activation energy of cerium
oxide acts to burn off carbon deposits within the engine cylinder at
the wall temperature and prevents the deposition of non-polar
compounds on the cylinder wall results reduction in HC emissions.
The tests revealed that cerium oxide nanoparticles can be used as
additive in diesel and diesel-biodiesel blends to improve complete
combustion of the fuel significantly.
Abstract: This paper represents an experimental study of LPG
diffusion flame at elevated preheated air temperatures. The flame is
stabilized in a vertical water-cooled combustor by using air swirler. An
experimental test rig was designed to investigate the different
operating conditions. The burner head is designed so that the LPG fuel
issued centrally and surrounded by the swirling air issues from an air
swirler. There are three air swirlers having the same dimensions but
having different blade angles to give different swirl numbers of 0.5,
0.87 and 1.5. The combustion air was heated electrically before
entering the combustor up to a temperature about 500 K. Five air to
fuel mass ratios of 15, 20, 30, 40 and 50 were also studied. The effect
of preheated air temperature, swirl number and air to fuel mass ratios
on the temperature maps, visible flame length, high temperature region
(size) and exhaust species concentrations are studied. Some results
show that as the preheated air temperature increases, the volume of
high temperature region also increased but the flame length decreased.
Increasing the preheated air temperature, EINOx, EICO2 and EIO2
increased, while EICO decreased. Increasing the preheated air
temperature from 300 to 500 K, for all air swirl numbers used, the
highest increase in EINOx, EICO2 and EIO2 are 141, 4 and 65%,
respectively.
Abstract: Experiential marketing is one of the marketing
approaches that offer an exceptional framework to integrate elements
of experience and entertainment in a product or service. Experiential
marketing is defined as a memorable experience that goes deeply into
the customer’s mind. Besides that, customer satisfaction is defined as
an emotional response to the experiences provided by and associated
with particular products or services purchased. Thus, experiential
marketing activities can affect the level of customer satisfaction and
loyalty. In this context, the research aims to explore the relationship
among experiential marketing, customer satisfaction and customer
loyalty among the cosmetic products customers in Konya. The partial
least squares (PLS) method is used to analyze the survey data.
Findings of the present study revealed that experiential marketing has
been a significant predictor of customer satisfaction and customer
loyalty, and also experiential marketing has a significantly positive
effect on customer satisfaction and customer loyalty.
Abstract: Crops diversity and maintaining and enhancing the
fertility of agricultural lands are basic principles of organic farming.
With a wider range of crops in agroecosystem can improve the ability
to control weeds, pests and diseases, and the performance of crops
rotation and food safety. In this sense, the main objective of the
research was to study the productivity and chemical composition of
some alternative crops and their adaptability to soil and climatic
conditions of the agricultural area in Southern Romania and to
cultivation in the organic farming system. The alternative crops were:
lentil (7 genotypes); five species of grain legumes (5 genotypes); four
species of oil crops (5 genotypes). The seed production was, on
average: 1343 kg/ha of lentil; 2500 kg/ha of field beans; 2400 kg/ha
of chick peas and blackeyed peas; more than 2000 kg/ha of atzuki
beans, over 1250 kg/ha of fenugreek; 2200 kg/ha of safflower; 570
kg/ha of oil pumpkin; 2150 kg/ha of oil flax; 1518 kg/ha of camelina.
Regarding chemical composition, lentil seeds contained: 22.18%
proteins, 3.03% lipids, 33.29% glucides, 4.00% minerals, and 259.97
kcal energy values. For field beans: 21.50% proteins, 4.40% lipids,
63.90% glucides, 5.85% minerals, 395.36 kcal energetic value. For
chick peas: 21.23% proteins, 4.55% lipids, 53.00% glucides, 3.67%
minerals, 348.22 kcal energetic value. For blackeyed peas: 23.30%
proteins, 2.10% lipids, 68.10% glucides, 3.93% minerals, 350.14 kcal
energetic value. For adzuki beans: 21.90% proteins, 2.60% lipids,
69.30% glucides, 4.10% minerals, 402.48 kcal energetic value. For
fenugreek: 21.30% proteins, 4.65% lipids, 63.83% glucides, 5.69%
minerals, 396.54 kcal energetic value. For safflower: 12.60%
proteins, 28.37% lipids, 46.41% glucides, 3.60% minerals, 505.78
kcal energetic value. For camelina: 20.29% proteins, 31.68% lipids,
36.28% glucides, 4.29% minerals, 526.63 kcal energetic value. For
oil pumpkin: 29.50% proteins, 36.92% lipids, 18.50% glucides,
5.41% minerals, 540.15 kcal energetic value. For oil flax: 22.56%
proteins, 34.10% lipids, 27.73% glucides, 5.25% minerals, 558.45
kcal energetic value.
Abstract: The Composite Shear Walls (CSW) with steel encased
profiles can be used as lateral-load resisting systems for buildings
that require considerable large lateral-load capacity. The aim of this
work is to propose the experimental work conducted on CSW having
L section folded plate (L shape steel made-up sections) as
longitudinal reinforcement in boundary regions. The study in this
paper present the experimental test conducted on CSW having L
section folded plate as longitudinal reinforcement in boundary
regions. The tested 1/3 geometric scaled CSW has aspect ratio of 3.2.
L-shape structural steel materials with 2L-19x57x7mm dimensions
were placed in shear wall boundary zones. The seismic behavior of
CSW test specimen was investigated by evaluating and interpreting
the hysteresis curves, envelope curves, rigidity and consumed energy
graphs of this tested element. In addition to this, the experimental
results, deformation and cracking patterns were evaluated, interpreted
and suggestions of the design recommendations were proposed.
Abstract: The use of engineered nanomaterials has increased as
a result of their positive impact on many sectors of the economy,
including agriculture. Silver nanoparticles (AgNPs) are now used to
enhance seed germination, plant growth, and photosynthetic quantum
efficiency and as antimicrobial agents to control plant diseases. In
this study, we examined the effect of AgNP dosage on the seed
germination of three plant species: corn (Zea mays L.), watermelon
(Citrullus lanatus [Thunb.] Matsum. & Nakai) and zucchini
(Cucurbita pepo L.). This experiment was designed to study the
effect of AgNPs on germination percentage, germination rate, mean
germination time, root length and fresh and dry weight of seedlings
for the three species. Seven concentrations (0.05, 0.1, 0.5, 1, 1.5, 2
and 2.5 mg/ml) of AgNPs were examined at the seed germination
stage. The three species had different dose responses to AgNPs in
terms of germination parameters and the measured growth
characteristics. The germination rates of the three plants were
enhanced in response to AgNPs. Significant enhancement of the
germination percentage values was observed after treatment of the
watermelon and zucchini plants with AgNPs in comparison with
untreated seeds. AgNPs showed a toxic effect on corn root
elongation, whereas watermelon and zucchini seedling growth were
positively affected by certain concentrations of AgNPs. This study
showed that exposure to AgNPs caused both positive and negative
effects on plant growth and germination.