Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: In this research work, neural networks were applied to
classify two types of hip joint implants based on the relative hip joint
implant side speed and three components of each ground reaction
force. The condition of walking gait at normal velocity was used and
carried out with each of the two hip joint implants assessed. Ground
reaction forces’ kinetic temporal changes were considered in the first
approach followed but discarded in the second one. Ground reaction
force components were obtained from eighteen patients under such
gait condition, half of which had a hip implant type I-II, whilst the
other half had the hip implant, defined as type III by Orthoload®.
After pre-processing raw gait kinetic data and selecting the time
frames needed for the analysis, the ground reaction force components
were used to train a MLP neural network, which learnt to distinguish
the two hip joint implants in the abovementioned condition. Further
to training, unknown hip implant side and ground reaction force
components were presented to the neural networks, which assigned
those features into the right class with a reasonably high accuracy for
the hip implant type I-II and the type III. The results suggest that
neural networks could be successfully applied in the performance
assessment of hip joint implants.
Abstract: Red River Gum (Eucalyptus camaldulensis) is a tree
of the genus Eucalyptus widely distributed in Algeria and in the
world. The value of its aromatic secondary metabolites offers new
perspectives in the pharmaceutical industry. This strategy can
contribute to the sustainable development of our country. Preliminary
tests performed on the essential oil of Eucalyptus camendulensis
showed that this oil has antibacterial activity vis-à-vis the bacterial
strains (Enterococcus feacalis, Enterobacter cloaceai, Proteus
microsilis, Escherichia coli, Klebsiella pneumonia, and Pseudomonas
aeruginosa) and antifungic (Fusarium sporotrichioide and Fusarium
graminearum). The culture medium used was nutrient broth Muller
Hinton. The interaction between the bacteria and the essential oil is
expressed by a zone of inhibition with diameters of MIC indirectly
expression of. And we used the PDA medium to determine the fungal
activity. The extraction of the aromatic fraction (essentially oilhydrolat)
of the fresh aerian part of the Eucalyptus camendulensis
was performed by hydrodistillation. The average essential oil yield is
0.99%. The antimicrobial and fungal study of the essential oil and
hydrosol showed a high inhibitory effect on the growth of pathogens.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.
Abstract: Estimation of a proportion has many applications in
economics and social studies. A common application is the estimation
of the low income proportion, which gives the proportion of people
classified as poor into a population. In this paper, we present this
poverty indicator and propose to use the logistic regression estimator
for the problem of estimating the low income proportion. Various
sampling designs are presented. Assuming a real data set obtained
from the European Survey on Income and Living Conditions, Monte
Carlo simulation studies are carried out to analyze the empirical
performance of the logistic regression estimator under the various
sampling designs considered in this paper. Results derived from
Monte Carlo simulation studies indicate that the logistic regression
estimator can be more accurate than the customary estimator under
the various sampling designs considered in this paper. The stratified
sampling design can also provide more accurate results.
Abstract: A total of 150 meat type chickens comprising 50 each
of Arbor Acre, Marshall and Ross were used for this study which
lasted for 10 weeks at the Federal University of Agriculture,
Abeokuta, Nigeria. Growth performance data were collected from the
third week through week 10 and data obtained were analysed using
the Generalized Linear Model Procedure. Heritability estimates (h2)
for body dimensions carried out on the chicken strains ranged from
low to high. Marshall broiler chicken strain had the highest h2 for
body weight 0.46±0.04, followed by Arbor Acre and Ross with h2
being 0.38±0.12 and 0.26±0.06, respectively. The repeatability
estimates for body weight in the three broiler strains were high, and it
ranged from 0.70 at week 4 to 0.88 at week 10. Relationships
between the body weight and linear body measurements in the broiler
chicken strains were positive and highly significant (p > 0.05).
Abstract: In order to investigate the effect of Plant Growth
Promoting Rhizobacteria (PGPR) and rhizobium bacteria on grain
yield and some agronomic traits of mungbean (Vigna radiate L.), an
experiment was carried out based on randomized complete block
design with three replications in Malekshahi, Ilam province, Iran
during 2012-2013 cropping season. Experimental treatments
consisted of control treatment, inoculation with rhizobium bacteria,
rhizobium bacteria and Azotobacter, rhizobium bacteria and
Azospirillum, rhizobium bacteria and Pseudomonas, rhizobium
bacteria, Azotobacter and Azospirillum, rhizobium bacteria,
Azotobacter and Pseudomonas, rhizobium bacteria, Azospirillum and
Pseudomonas and rhizobium bacteria, Azotobacter, Azospirillum and
Pseudomonas. The results showed that the effect of PGPR and
rhizobium bacteria were significant affect on grain and its
components in mungbean plant. Grain yield significantly increased
by PGPR and rhizobium bacteria, so that the maximum grain yield
was obtained from rhizobium bacteria + Azospirillum +
Pseudomonas with the amount of 2287 kg.ha-1 as compared to
control treatment. Excessive application of chemical fertilizers causes
environmental and economic problems. That is, the overfertilization
of P and N leads to pollution due to soil erosion and runoff water, so
the use of PGPR and rhizobium bacteria can be justified due to
reduce input costs, increase in grain yield and environmental friendly.
Abstract: Voltage sags are the most common power quality
disturbance in the distribution system. It occurs due to the fault in the
electrical network or by the starting of a large induction motor and
this can be solved by using the custom power devices such as
Dynamic Voltage Restorer (DVR). In this paper DVR is proposed to
compensate voltage sags on critical loads dynamically. The DVR
consists of VSC, injection transformers, passive filters and energy
storage (lead acid battery). By injecting an appropriate voltage, the
DVR restores a voltage waveform and ensures constant load voltage.
The simulation and experimental results of a DVR using MATLAB
software shows clearly the performance of the DVR in mitigating
voltage sags.
Abstract: Pomegranate (Punica granatum L.) is an ancient fruit of great medical interest and rich source of antioxidants. Pesticides as dimethoate play a crucial role in the occurrence many diseases in plants, animal and human. Therefore the ability of Pomegranate (Punica granatum L.) to alleviate hepatotoxicity induced by organophosphate pesticide dimethoate was investigated. Albino male rats were divided randomly into 4 groups and kept at 7 animals per group in an environmentally controlled condition for 6 weeks. The first group was served as a control group (basal diet), the second group fed on basal diet supplemented with 5% freeze dried pomegranate seeds, the third group fed on 20 ppm dimethoate contaminated diet and the last group fed on dimethoate contaminated diet supplemented with 5% freeze dried pomegranate seeds. The results revealed that administration of dimethoate caused high significant increased in liver functions: alanine aminotransferase (ALT), aspartate aminotransferase (AST), alkaline phosphatase (ALP) activities as well as lipid peroxide (malonaldhyde, MDA); on the other hand high significant decreased on glutathione (GSH), glutathione peroxidase (GPx), albumin and total protein were observed. However addition of 5% freeze dried pomegranate seeds significantly improved all previously mentioned parameters. These results indicate the dimethoate induced hepatotoxicity and highlight the protective effect of pomegranate seeds as a potential protective agent against dimethoate induced hepatotoxicity. This may be attributed to the powerful antioxidants (polyphenols, total phenols, and total flavonoids) which present in high levels in pomegranate as well as improving the immunity by activation of antioxidant enzymes GSH and GPx.
Abstract: In development of floating photovoltaic generation
system, finding a suitable place of installation is as important as
development of economically feasible and stable structure. Especially
since floating photovoltaic system has its facility floating on water
surface, it is extremely important to review the effects of weather
conditions such as wind, water flow and floating matters, various
factors (such as fogs) that can reduce generation efficiency, possibility
of connection with power system, and legal restrictions. The method of
investigating suitable area and resource for development of
tracking-type floating photovoltaic generation system was proposed in
this paper, which can be used for development of floating and ocean
photovoltaic system in the future.
Abstract: This paper aims at finding a suitable neural network
for monitoring congestion level in electrical power systems. In this
paper, the input data has been framed properly to meet the target
objective through supervised learning mechanism by defining normal
and abnormal operating conditions for the system under study. The
congestion level, expressed as line congestion index (LCI), is
evaluated for each operating condition and is presented to the NN
along with the bus voltages to represent the input and target data.
Once, the training goes successful, the NN learns how to deal with a
set of newly presented data through validation and testing
mechanism. The crux of the results presented in this paper rests on
performance comparison of a multi-layered feed forward neural
network with eleven types of back propagation techniques so as to
evolve the best training criteria. The proposed methodology has been
tested on the standard IEEE-14 bus test system with the support of
MATLAB based NN toolbox. The results presented in this paper
signify that the Levenberg-Marquardt backpropagation algorithm
gives best training performance of all the eleven cases considered in
this paper, thus validating the proposed methodology.
Abstract: In healthy humans, the cortical brain rhythm shows
specific mu (~6-14 Hz) and beta (~18-24 Hz) band patterns in the
cases of both real and imaginary motor movements. As cerebellar
ataxia is associated with impairment of precise motor movement
control as well as motor imagery, ataxia is an ideal model system in
which to study the role of the cerebellocortical circuit in rhythm
control. We hypothesize that the EEG characteristics of ataxic patients
differ from those of controls during the performance of a
Brain-Computer Interface (BCI) task. Ataxia and control subjects
showed a similar distribution of mu power during cued relaxation.
During cued motor imagery, however, the ataxia group showed
significant spatial distribution of the response, while the control group
showed the expected decrease in mu-band power (localized to the
motor cortex).
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: This research proposes a novel reconstruction protocol
for restoring missing surfaces and low-quality edges and shapes in
photos of artifacts at historical sites. The protocol starts with the
extraction of a cloud of points. This extraction process is based on
four subordinate algorithms, which differ in the robustness and
amount of resultant. Moreover, they use different -but
complementary- accuracy to some related features and to the way
they build a quality mesh. The performance of our proposed protocol
is compared with other state-of-the-art algorithms and toolkits. The
statistical analysis shows that our algorithm significantly outperforms
its rivals in the resultant quality of its object files used to reconstruct
the desired model.
Abstract: In this study, a comparative analysis of the approaches
associated with the use of neural network algorithms for effective
solution of a complex inverse problem – the problem of identifying
and determining the individual concentrations of inorganic salts in
multicomponent aqueous solutions by the spectra of Raman
scattering of light – is performed. It is shown that application of
artificial neural networks provides the average accuracy of
determination of concentration of each salt no worse than 0.025 M.
The results of comparative analysis of input data compression
methods are presented. It is demonstrated that use of uniform
aggregation of input features allows decreasing the error of
determination of individual concentrations of components by 16-18%
on the average.
Abstract: This paper presents a 3D guidance scheme for
Unmanned Aerial Vehicles (UAVs). The proposed guidance scheme
is based on the sliding mode approach using nonlinear sliding
manifolds. Generalized 3D kinematic equations are considered
here during the design process to cater for the coupling between
longitudinal and lateral motions. Sliding mode based guidance
scheme is then derived for the multiple-input multiple-output
(MIMO) system using the proposed nonlinear manifolds. Instead of
traditional sliding surfaces, nonlinear sliding surfaces are proposed
here for performance and stability in all flight conditions. In the
reaching phase control inputs, the bang-bang terms with signum
functions are accompanied with proportional terms in order to reduce
the chattering amplitudes. The Proposed 3D guidance scheme is
implemented on a 6-degrees-of-freedom (6-dof) simulation of a UAV
and simulation results are presented here for different 3D trajectories
with and without disturbances.
Abstract: During welding, the amount of heat present in weld
zones determines the quality of weldment produced. Thus, the heat
distribution characteristics and its magnitude in weld zones with
respect to process variables such as tool pin-shoulder rotational and
traveling speed during welding is analyzed using thermal finite
element analyses method. For this purpose, transient thermal finite
element analyses are performed to model the temperatures
distribution and its quantities in weld-zones with respect to process
variables such as rotational speed and traveling speed during welding.
Commercially available software Altair HyperWork is used to model
three-dimensional tool pin-shoulder vs. workpieces and to simulate
the friction stir process. The results show that increasing tool
rotational speed, at a constant traveling speed, will increase the
amount of heat generated in weld-zones. In contrary, increasing
traveling speed, at constant tool pin-shoulder rotational speeds, will
reduce the amount of heat generated in weld zones.