Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: In this paper, we propose a morphing method by which face color images can be freely transformed. The main focus of this work is the transformation of one face image to another. This method is fully automatic in that it can morph two face images by automatically detecting all the control points necessary to perform the morph. A face detection neural network, edge detection and medium filters are employed to detect the face position and features. Five control points, for both the source and target images, are then extracted based on the facial features. Triangulation method is then used to match and warp the source image to the target image using the control points. Finally color interpolation is done using a color Gaussian model that calculates the color for each particular frame depending on the number of frames used. A real coded Genetic algorithm is used in both the image warping and color blending steps to assist in step size decisions and speed up the morphing. This method results in ''very smooth'' morphs and is fast to process.
Abstract: A robust AUSM+ upwind discretisation scheme has been developed to simulate multiphase flow using consistent spatial discretisation schemes and a modified low-Mach number diffusion term. The impact of the selection of an interfacial pressure model has also been investigated. Three representative test cases have been simulated to evaluate the accuracy of the commonly-used stiffenedgas equation of state with respect to the IAPWS-IF97 equation of state for water. The algorithm demonstrates a combination of robustness and accuracy over a range of flow conditions, with the stiffened-gas equation tending to overestimate liquid temperature and density profiles.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: Conventional materials like glass, wood or metals
replacement with polymer materials is still continuing. More simple
thus cheaper production is the main reason. However due to high
energy and petrochemical prices are polymer prices increasing too.
That´s why various kinds of fillers are used to make polymers
cheaper. Of course target is to maintain or improve properties of
these compounds. In this paper are solved rheology issues of
polymers compounded with vegetal origin fibers.
Abstract: This is a genetic comparison study of Arabian Oryx
(Oryx leucoryx) population at two different locations (A &B) based
on nuclear microsatellite DNA markers. Arabian Oryx is listed as
vulnerable and endanger by the World Conservation Union (IUCN).
Thirty microsatellite markers from bovine family were applied to
investigate the genetic diversity of the Arabian Oryx and to set up a
molecular inventory. Among 30 microsatellite markers used, 13
markers were moderately polymorphic. Arabian Oryx at location A
has shown better gene diversity over location B. However, mean
number of alleles were less than location B. Data of within
population inbreeding coefficient indicates inbreeding at both
locations (A&B). Based on the analysis of polymorphic microsatellite
markers, the study revealed that Arabian Oryx need a genetically
designed breeding program.
Abstract: By taking advantage of both k-NN which is highly
accurate and K-means cluster which is able to reduce the time of classification, we can introduce Cluster-k-Nearest Neighbor as "variable k"-NN dealing with the centroid or mean point of all subclasses generated by clustering algorithm. In general the algorithm of K-means cluster is not stable, in term of accuracy, for that reason we develop another algorithm for clustering our space which gives a higher accuracy than K-means cluster, less
subclass number, stability and bounded time of classification with respect to the variable data size. We find between 96% and 99.7 % of accuracy in the lassification of 6 different types of Time series by using K-means cluster algorithm and we find 99.7% by using the new clustering algorithm.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: Minimization methods for training feed-forward networks with Backpropagation are compared. Feedforward network training is a special case of functional minimization, where no explicit model of the data is assumed. Therefore due to the high dimensionality of the data, linearization of the training problem through use of orthogonal basis functions is not desirable. The focus is functional minimization on any basis. A number of methods based on local gradient and Hessian matrices are discussed. Modifications of many methods of first and second order training methods are considered. Using share rates data, experimentally it is proved that Conjugate gradient and Quasi Newton?s methods outperformed the Gradient Descent methods. In case of the Levenberg-Marquardt algorithm is of special interest in financial forecasting.
Abstract: An important problem in speech research is the automatic extraction of information about the shape and dimensions of the vocal tract during real-time speech production. We have previously developed Southampton dynamic magnetic resonance imaging (SDMRI) as an approach to the solution of this problem.However, the SDMRI images are very noisy so that shape extraction is a major challenge. In this paper, we address the problem of tongue shape extraction, which poses difficulties because this is a highly deforming non-parametric shape. We show that combining active shape models with the dynamic Hough transform allows the tongue shape to be reliably tracked in the image sequence.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: Although many researchers have studied the flow
hydraulics in compound channels, there are still many complicated problems in determination of their flow rating curves. Many different
methods have been presented for these channels but extending them
for all types of compound channels with different geometrical and
hydraulic conditions is certainly difficult. In this study, by aid of nearly 400 laboratory and field data sets of geometry and flow rating
curves from 30 different straight compound sections and using artificial neural networks (ANNs), flow discharge in compound channels was estimated. 13 dimensionless input variables including relative depth, relative roughness, relative width, aspect ratio, bed
slope, main channel side slopes, flood plains side slopes and berm
inclination and one output variable (flow discharge), have been used
in ANNs. Comparison of ANNs model and traditional method
(divided channel method-DCM) shows high accuracy of ANNs model results. The results of Sensitivity analysis showed that the relative depth with 47.6 percent contribution, is the most effective input parameter for flow discharge prediction. Relative width and
relative roughness have 19.3 and 12.2 percent of importance, respectively. On the other hand, shape parameter, main channel and
flood plains side slopes with 2.1, 3.8 and 3.8 percent of contribution, have the least importance.
Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: The agricultural organic farming is different from
conventional farming in a way that is aimed at providing a balanced
and constructive action in agricultural systems. With the increase in
intensive agriculture, undesirable changes were being observed in
ecosystems with irreparable damage being caused to the natural
equilibrium. This is the reason for the increasing interest in organic
farming as an environment friendly agricultural production method.
In the present work three red fruits produced in organic farming were
analyzed, namely raspberry, gooseberry and blueberry. The samples
were harvested in a local farm when at plain maturation. The results
obtained allowed to conclude that the blueberry contained higher
amounts of phenolic compounds, total tannins and total anthocyanins
than raspberry and gooseberry. Furthermore, the HPLC analysis
allowed to identify monomeric anthocyanins and phenolic acids in
the three fruits studied.
Abstract: Like other external sorting algorithms, the presented
algorithm is a two step algorithm including internal and external
steps. The first part of the algorithm is like the other similar
algorithms but second part of that is including a new easy
implementing method which has reduced the vast number of inputoutput
operations saliently. As decreasing processor operating time
does not have any effect on main algorithm speed, any improvement
in it should be done through decreasing the number of input-output
operations. This paper propose an easy algorithm for choose the
correct record location of the final list. This decreases the time
complexity and makes the algorithm faster.
Abstract: Demand over web services is in growing with increases number of Web users. Web service is applied by Web application. Web application size is affected by its user-s requirements and interests. Differential in requirements and interests lead to growing of Web application size. The efficient way to save store spaces for more data and information is achieved by implementing algorithms to compress the contents of Web application documents. This paper introduces an algorithm to reduce Web application size based on reduction of the contents of HTML files. It removes unimportant contents regardless of the HTML file size. The removing is not ignored any character that is predicted in the HTML building process.
Abstract: This article discusses the prospects of participation of
the Republic of Kazakhstan in Hague Conference on Private
International Law on the unification of collision law in the
international trade.
The article analyzes some conventions on international trade. The
appropriate conclusions based on the opinions of scientists and
experts in this field have been made. First, all issues presented in the
form of gaps or spaces in conventions should be the subject to direct
negotiations in the course of the activities of Hague Conference, and
have a comprehensive feature, be transparent and taken under
simplified procedure.
Secondly, one should not underestimate the value of conventions
that do not become active due to various reasons and having a
positive impact on the development and improvement of national
legislation and practice in the field of private international law.
Thirdly, Kazakhstan has to reconsider its attitude to Hague
Conference, having become its full member and aiming at providing
constructive and fruitful cooperation with both the organization itself
and its member states.
Abstract: In this article, a single application is suggested to determine the position of vehicles using Geographical Information Systems (GIS) and Geographical Position Systems (GPS). The part of the article material included mapping three dimensional coordinates to two dimensional coordinates using UTM or LAMBERT geographical methods, and the algorithm of conversion of GPS information into GIS maps is studied. Also, suggestions are given in order to implement this system based on web (called web based systems). To apply this system in IRAN, related official in this case are introduced and their duties are explained. Finally, economy analyzed is assisted according to IRAN communicational system.