Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: DC-DC converters are widely used in regulated switched mode power supplies and in DC motor drive applications. There are several sources of unwanted nonlinearity in practical power converters. In addition, their operation is characterized by switching that gives birth to a variety of nonlinear dynamics. DC-DC buck and boost converters controlled by pulse-width modulation (PWM) have been simulated. The voltage waveforms and attractors obtained from the circuit simulation have been studied. With the onset of instability, the phenomenon of subharmonic oscillations, quasi-periodicity, bifurcations, and chaos have been observed. This paper is mainly motivated by potential contributions of chaos theory in the design, analysis and control of power converters, in particular and power electronics circuits, in general.
Abstract: This paper presents an adaptive nonlinear position
controller with velocity constraint, capable of combining the
input-output linearization technique and Lyapunov stability theory.
Based on the Lyapunov stability theory, the adaptation law of the
proposed controller is derived along with the verification of the overall
system-s stability. Computer simulation results demonstrate that the
proposed controller is robust and it can ensure transient stability of
BLDCM, under the occurrence of a large sudden fault.
Abstract: In H.264/AVC video encoding, rate-distortion
optimization for mode selection plays a significant role to achieve
outstanding performance in compression efficiency and video quality.
However, this mode selection process also makes the encoding
process extremely complex, especially in the computation of the ratedistortion
cost function, which includes the computations of the sum
of squared difference (SSD) between the original and reconstructed
image blocks and context-based entropy coding of the block. In this
paper, a transform-domain rate-distortion optimization accelerator
based on fast SSD (FSSD) and VLC-based rate estimation algorithm
is proposed. This algorithm could significantly simplify the hardware
architecture for the rate-distortion cost computation with only
ignorable performance degradation. An efficient hardware structure
for implementing the proposed transform-domain rate-distortion
optimization accelerator is also proposed. Simulation results
demonstrated that the proposed algorithm reduces about 47% of total
encoding time with negligible degradation of coding performance.
The proposed method can be easily applied to many mobile video
application areas such as a digital camera and a DMB (Digital
Multimedia Broadcasting) phone.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components, and only their weight is accounted for in
practical structural design. In this study, the brick-infill panels are
simulated by compression struts to clarify their effect on the
progressive collapse potential of an earthquake-resistant RC building.
Three-dimensional finite element models are constructed for the RC
building subjected to sudden column loss. Linear static analyses are
conducted to investigate the variation of demand-to-capacity ratio
(DCR) of beam-end moment and the axial force variation of the beams
adjacent to the removed column. Study results indicate that the
brick-infill effect depends on their location with respect to the
removed column. As they are filled in a structural bay with a shorter
span adjacent to the column-removed line, more significant reduction
of DCR may be achieved. However, under certain conditions, the
brick infill may increase the axial tension of the two-span beam
bridging the removed column.
Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: Applying a rigorous process to optimize the elements
of a supply-chain network resulted in reduction of the waiting time
for a service provider and customer. Different sources of downtime
of hydraulic pressure controller/calibrator (HPC) were causing
interruptions in the operations. The process examined all the issues to
drive greater efficiencies. The issues included inherent design issues
with HPC pump, contamination of the HPC with impurities, and the
lead time required for annual calibration in the USA.
HPC is used for mandatory testing/verification of formation
tester/pressure measurement/logging-while drilling tools by oilfield
service providers, including Halliburton.
After market study andanalysis, it was concluded that the current
HPC model is best suited in the oilfield industry. To use theexisting
HPC model effectively, design andcontamination issues were
addressed through design and process improvements. An optimum
network is proposed after comparing different supply-chain models
for calibration lead-time reduction.
Abstract: The perfect operation of common Active Filters is depended on accuracy of identification system distortion. Also, using a suitable method in current injection and reactive power compensation, leads to increased filter performance. Due to this fact, this paper presents a method based on predictive current control theory in shunt active filter applications. The harmonics of the load current is identified by using o–d–q reference frame on load current and eliminating the DC part of d–q components. Then, the rest of these components deliver to predictive current controller as a Threephase reference current by using Park inverse transformation. System is modeled in discreet time domain. The proposed method has been tested using MATLAB model for a nonlinear load (with Total Harmonic Distortion=20%). The simulation results indicate that the proposed filter leads to flowing a sinusoidal current (THD=0.15%) through the source. In addition, the results show that the filter tracks the reference current accurately.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: The Object of this paper is to design and analyze a
Hysteresis modulation based sliding mode control (HMSMC) for
positive output elementary super lift Luo converter (POESLLC),
which is the start-of-the-art DC-DC converter. The positive output
elementary super lift Luo converter performs the voltage
conversion from positive source voltage to positive load voltage.
This paper proposes a HMSMC capable of providing the good
steady state and dynamic performance compared to conventional
controllers. Dynamic equations describing the positive output
elementary super lift luo converter are derived by using state space
average method. The simulation model of the positive output
elementary super lift Luo converter with its control circuit is
implemented in Matlab/Simulink. The HMSMC for positive
output elementary super lift Luo converter is tested for line
changes, load changes and also for components variations.
Abstract: The object of this work is the probabilistic performance evaluation of safety instrumented systems (SIS), i.e. the average probability of dangerous failure on demand (PFDavg) and the average frequency of failure (PFH), taking into account the uncertainties related to the different parameters that come into play: failure rate (λ), common cause failure proportion (β), diagnostic coverage (DC)... This leads to an accurate and safe assessment of the safety integrity level (SIL) inherent to the safety function performed by such systems. This aim is in keeping with the requirement of the IEC 61508 standard with respect to handling uncertainty. To do this, we propose an approach that combines (1) Monte Carlo simulation and (2) fuzzy sets. Indeed, the first method is appropriate where representative statistical data are available (using pdf of the relating parameters), while the latter applies in the case characterized by vague and subjective information (using membership function). The proposed approach is fully supported with a suitable computer code.
Abstract: This paper deals with the optimal design of two-channel recursive parallelogram quadrature mirror filter (PQMF) banks. The analysis and synthesis filters of the PQMF bank are composed of two-dimensional (2-D) recursive digital all-pass filters (DAFs) with nonsymmetric half-plane (NSHP) support region. The design problem can be facilitated by using the 2-D doubly complementary half-band (DC-HB) property possessed by the analysis and synthesis filters. For finding the coefficients of the 2-D recursive NSHP DAFs, we appropriately formulate the design problem to result in an optimization problem that can be solved by using a weighted least-squares (WLS) algorithm in the minimax (L∞) optimal sense. The designed 2-D recursive PQMF bank achieves perfect magnitude response and possesses satisfactory phase response without requiring extra phase equalizer. Simulation results are also provided for illustration and comparison.
Abstract: The absolute Cu atoms density in Cu(2S1/22P1/2)
ground state has been measured by Resonance Optical Absorption
(ROA) technique in a DC magnetron sputtering deposition with
argon. We measured these densities under variety of operation
conditions: pressure from 0.6 μbar to 14 μbar, input power from
10W to 200W and N2 mixture from 0% to 100%. For measuring the
gas temperature, we used the simulation of N2 rotational spectra
with a special computer code. The absolute number density of Cu
atoms decreases with increasing the N2 percentage of buffer gas at
any conditions of this work. But the deposition rate, is not decreased
with the same manner. The deposition rate variation is very small
and in the limit of quartz balance measuring equipment accuracy. So
we conclude that decrease in the absolute number density of Cu
atoms in magnetron plasma has not a big effect on deposition rate,
because the diffusion of Cu atoms to the chamber volume and
deviation of Cu atoms from direct path (towards the substrate)
decreases with increasing of N2 percentage of buffer gas. This is
because of the lower mass of N2 atoms compared to the argon ones.
Abstract: Reduced switching loss favours Pulse Skipping
Modulation mode of switching dc-to-dc converters at light loads.
Under certain conditions the converter operates in discontinuous
conduction mode (DCM). Inductor current starts from zero in each
switching cycle as the switching frequency is constant and not
adequately high. A DC-to-DC buck converter is modelled and
simulated in this paper under DCM. Effect of ESR of the filter
capacitor in input current frequency components is studied. The
converter is studied for its operation under input voltage and load
variation. The operating frequency is selected to be close to and
above audio range.
Abstract: The Indian subcontinent is facing a massive challenge with regards to the energy security in member countries, i.e. providing a reliable source of electricity to facilitate development across various sectors of the economy and thereby achieve the developmental targets it has set for itself. A highly precarious situation exists in the subcontinent which is observed in the series of system failures which most of the times leads to system collapses-blackouts. To mitigate the issues related with energy security as well as keep in check the increasing supply demand gap, a possible solution that stands in front of the subcontinent is the deployment of an interconnected electricity ‘Supergrid’ designed to carry huge quanta of power across the sub continent as well as provide the infra structure for RES integration. This paper assesses the need and conditions for a Supergrid deployment and consequently proposes a meshed topology based on VSC HVDC converters for the Supergrid modeling.
Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: With a development of Hybrid Electric Vehicle(HEV),
A photovoltaic(PV) generation system is used for charging batteries in many cases. A dc/dc converter using PV power for a battery charger
requires a high efficiency. In this paper, A ZVS boost converter using the renewable energies for HEV charger is proposed. Through the theoretical analysis and experimental result, operation modes and characteristics of the proposed topology are verified.
Abstract: The 4G front-end transceiver needs a high
performance which can be obtained mainly with an optimal
architecture and a multi-band Local Oscillator. In this study, we
proposed and presented a new architecture of multi-band frequency
synthesizer based on an Inverse Sine Phase Detector Phase Locked
Loop (ISPD PLL) without any filters and any controlled gain block
and associated with adapted multi band LC tuned VCO using a
several numeric controlled capacitive branches but not binary
weighted. The proposed architecture, based on 0.35μm CMOS
process technology, supporting Multi-band GSM/DCS/DECT/
UMTS/WiMax application and gives a good performances: a phase
noise @1MHz -127dBc and a Factor Of Merit (FOM) @ 1MHz -
186dB and a wide band frequency range (from 0.83GHz to 3.5GHz),
that make the proposed architecture amenable for monolithic
integration and 4G multi-band application.