Abstract: Air bubbles have been detected in human circulation
of end-stage renal disease patients who are treated by hemodialysis.
The consequence of air embolism, air bubbles, is under recognized
and usually overlooked in daily practice. This paper shows results of
a capacitor based detection method that capable of detecting the
presence of air bubbles in the blood stream in different frequencies.
The method is based on a parallel plates capacitor made of platinum
with an area of 1.5 cm2 and a distance between the two plates is 1cm.
The dielectric material used in this capacitor is Dextran70 solution
which mimics blood rheology. Simulations were carried out using
RC circuit at two frequencies 30Hz and 3 kHz and results compared
with experiments and theory. It is observed that by injecting air
bubbles of different diameters into the device, there were significant
changes in the capacitance of the capacitor. Furthermore, it is
observed that the output voltage from the circuit increased with
increasing air bubble diameter. These results demonstrate the
feasibility of this approach in improving air bubble detection in
Hemodialysis.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: It is difficult to judge ripeness by outward
characteristics such as size or external color. In this paper a nondestructive
method was studied to determine watermelon (Crimson
Sweet) quality. Responses of samples to excitation vibrations were
detected using laser Doppler vibrometry (LDV) technology. Phase
shift between input and output vibrations were extracted overall
frequency range. First and second were derived using frequency
response spectrums. After nondestructive tests, watermelons were
sensory evaluated. So the samples were graded in a range of ripeness
based on overall acceptability (total desired traits consumers).
Regression models were developed to predict quality using obtained
results and sample mass. The determination coefficients of the
calibration and cross validation models were 0.89 and 0.71
respectively. This study demonstrated feasibility of information
which is derived vibration response curves for predicting fruit
quality. The vibration response of watermelon using the LDV method
is measured without direct contact; it is accurate and timely, which
could result in significant advantage for classifying watermelons
based on consumer opinions.
Abstract: The aim of this study is to emphasize the opportunities in space design under the aspect of HCI as performance areas. HCI is a multidisciplinary approach that could be identified in many different areas. The aesthetical reflections of HCI by virtual reality in space design are the high-tech solutions of the new innovations as computational facilities by artistic features. The method of this paper is to identify the subject in 3 main parts. In the first part a general approach and definition of interactivity on the basis of space design; in the second part the concept of multimedia interactive theater by some chosen samples from the world and interactive design aspects; in the third part the samples from Turkey will be identified by stage designing principles. In the results it could be declared that the multimedia database is the virtual approach of theatre stage designing regarding interactive means by computational facilities according to aesthetical aspects. HCI is mostly identified in theatre stages as computational intelligence under the affect of interactivity.
Abstract: This paper considers the influence of promotion
instruments for renewable energy sources (RES) on a multi-energy
modeling framework. In Europe, so called Feed-in Tariffs are
successfully used as incentive structures to increase the amount of
energy produced by RES. Because of the stochastic nature of large
scale integration of distributed generation, many problems have
occurred regarding the quality and stability of supply. Hence, a
macroscopic model was developed in order to optimize the power
supply of the local energy infrastructure, which includes electricity,
natural gas, fuel oil and district heating as energy carriers. Unique
features of the model are the integration of RES and the adoption of
Feed-in Tariffs into one optimization stage. Sensitivity studies are
carried out to examine the system behavior under changing profits
for the feed-in of RES. With a setup of three energy exchanging
regions and a multi-period optimization, the impact of costs and
profits are determined.
Abstract: Abstraction of water from the dry river sand-beds is
well-known as an alternative source of water during dry seasons.
Internally, because of the form of sand particles, voids are created
which can store water in the riverbeds. Large rivers are rare in South
Africa. Many rivers are sand river types and without water during the
prolonged dry periods. South Africa has not taken full advantage of
water storage in sand as a solution to the growing water scarcity both
in urban and rural areas. The paper reviews the benefits of run-off
storage in sand reservoirs gained from other arid areas and need for
adoption in rural areas of South Africa as an alternative water supply
where it is probable.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: In the present study, the surface temperature history of the adaptor part in a two-stage supersonic launch vehicle is accurately predicted. The full Navier-Stokes equations are used to estimate the aerodynamic heat flux and the one-dimensional heat conduction in solid phase is used to compute the temperature history. The instantaneous surface temperature is used to improve the applied heat flux, to improve the accuracy of the results.
Abstract: Rotating stages in semiconductor, display industry and many other fields require challenging accuracy to perform their functions properly. Especially, Axis of rotation error on rotary system is significant; such as the spindle error motion of the aligner, wire bonder and inspector machine which result in the poor state of manufactured goods. To evaluate and improve the performance of such precision rotary stage, unessential movements on the other 5 degrees of freedom of the rotary stage must be measured and analyzed. In this paper, we have measured the three translations and two tilt motions of a rotating stage with high precision capacitive sensors. To obtain the radial error motion from T.I.R (Total Indicated Reading) of radial direction, we have used Donaldson's reversal technique. And the axial components of the spindle tilt error motion can be obtained accurately from the axial direction outputs of sensors by Estler face motion reversal technique. Further more we have defined and measured the sensitivity of positioning error to the five error motions.
Abstract: An improved topology of a voltage-fed quasi-resonant
soft switching LCrCdc series-parallel half bridge inverter with a constant-frequency for electronic ballast applications is proposed in this paper. This new topology introduces a low-cost solution to
reduce switching losses and circuit rating to achieve high-efficiency
ballast. Switching losses effect on ballast efficiency is discussed
through experimental point of view. In this discussion, an improved
topology in which accomplishes soft switching operation over a wide
power regulation range is proposed. The proposed structure uses reverse recovery diode to provide better operation for the ballast system. A symmetrical pulse wide modulation (PWM) control scheme is implemented to regulate a wide range of out-put power.
Simulation results are kindly verified with the experimental
measurements obtained by ballast-lamp laboratory prototype. Different load conditions are provided in order to clarify the
performance of the proposed converter.
Abstract: Variable ordering heuristics are used in constraint satisfaction algorithms. Different characteristics of various variable ordering heuristics are complementary. Therefore we have tried to get the advantages of all heuristics to improve search algorithms performance for solving constraint satisfaction problems. This paper considers combinations based on products and quotients, and then a newer form of combination based on weighted sums of ratings from a set of base heuristics, some of which result in definite improvements in performance.
Abstract: Imperfect knowledge cannot be avoided all the time. Imperfections may have several forms; uncertainties, imprecision and incompleteness. When we look to classification of methods for the management of imperfect knowledge we see fuzzy set-based techniques. The choice of a method to process data is linked to the choice of knowledge representation, which can be numerical, symbolic, logical or semantic and it depends on the nature of the problem to be solved for example decision support, which will be mentioned in our study. Fuzzy Logic is used for its ability to manage imprecise knowledge, but it can take advantage of the ability of neural networks to learn coefficients or functions. Such an association of methods is typical of so-called soft computing. In this study a new method was used for the management of imprecision for collected knowledge which related to economic analysis of construction industry in Turkey. Because of sudden changes occurring in economic factors decrease competition strength of construction companies. The better evaluation of these changes in economical factors in view of construction industry will made positive influence on company-s decisions which are dealing construction.
Abstract: The H.264/AVC standard is a highly efficient video
codec providing high-quality videos at low bit-rates. As employing
advanced techniques, the computational complexity has been
increased. The complexity brings about the major problem in the
implementation of a real-time encoder and decoder. Parallelism is the
one of approaches which can be implemented by multi-core system.
We analyze macroblock-level parallelism which ensures the same bit
rate with high concurrency of processors. In order to reduce the
encoding time, dynamic data partition based on macroblock region is
proposed. The data partition has the advantages in load balancing and
data communication overhead. Using the data partition, the encoder
obtains more than 3.59x speed-up on a four-processor system. This
work can be applied to other multimedia processing applications.
Abstract: The purpose of the present study is to analyze the
effect of the target plate-s curvature on the heat transfer in laminar
confined impinging jet flows. Numerical results from two
dimensional compressible finite volume solver are compared
between three different shapes of impinging plates: Flat, Concave
and Convex plates. The remarkable result of this study proves that
the stagnation Nusselt number in laminar range of Reynolds number
based on the slot width is maximum in convex surface and is
minimum in concave plate. These results refuse the previous data in
literature stating the amount of the stagnation Nusselt number is
greater in concave surface related to flat plate configuration.
Abstract: This research aimed to study the competency of health
and wellness hotels and resorts in developing use the local natural
resources and wisdom to conform to the national health and wellness
tourism (HWT) strategy by comparing two independent samples,
from Aumpur Muang, Ranong province and Aumpur Muang,
Chiangmai province. And also study in the suggestive direct path to
lead the organization to the sustainable successful.
This research was conduct by using mix methodology; both
quantitative and qualitative data were used. The data of competency
of health and wellness hotels and resorts (HWHR) in developing use
the local natural resources for HWT promoting were collected via
300 set of questionnaires, from 6 hotels and resorts in 2 areas, 3
places from Aumpur Muang, Ranong province and another 3 from
Aumpur Muang, Chiangmai province.
Thestudy of HWHR’s competency in developing use the local
natural resources and wisdom to conform to the national HWT
strategycan be divided into fourmain areas, food and beverages
service, tourism activity, environmental service, and value adding.
The total competency of the Chiangmai sample is importantly
scoredp. value 0.01 higher than the Ranong one while the area of
safety, Chiangmai’s competency is importantly scored 0.05 higher
than the Ranong’scompetency. Others were rated not differently.
Since Chiangmai perform better, then it can be a role model in
developing HTHR or HWT destination.
From the part of qualitative research, content analysis of business
contents and its environments were analyzed. The four stages of
strategic development and plans, from the smallest scale to the largest
scale such a national base were discussed. The HWT: Evolution
model and strategy for lodging Business were suggested. All those
stages must work harmoniously together. The distinctive result
illustrates the need of human resource development as the key point
to create the identity of Thainess on Health and wellness service
providing. This will add-on the value of services and differentiates
ourselves from other competitors. The creative of Thailand’s health
and wellness brand possibly increase loyalty customers which agreed
to be a path of sustainable development.
Abstract: In switch mode power inverters, small sized inverters
can be obtained by increasing the switching frequency. Switching
frequency increment causes high driver losses. Also, high dt
di
and
dt
dv
produced by the switching action creates high Electromagnetic
Interference (EMI) and Radio Frequency Interference (RFI). In this
paper, a series half bridge series resonant inverter circuit is simulated
and evaluated practically to demonstrate the turn-on and turn-off
conditions during zero or close to zero voltage switching. Also, the
reverse recovery current effects of the body diode of the MOSFETs
were investigated by operating above and below resonant frequency.
Abstract: A theory for optimal filtering of infinite sets of random
signals is presented. There are several new distinctive features of the
proposed approach. First, a single optimal filter for processing any
signal from a given infinite signal set is provided. Second, the filter is
presented in the special form of a sum with p terms where each term
is represented as a combination of three operations. Each operation
is a special stage of the filtering aimed at facilitating the associated
numerical work. Third, an iterative scheme is implemented into the
filter structure to provide an improvement in the filter performance at
each step of the scheme. The final step of the scheme concerns signal
compression and decompression. This step is based on the solution of
a new rank-constrained matrix approximation problem. The solution
to the matrix problem is described in this paper. A rigorous error
analysis is given for the new filter.
Abstract: A 2.4GHz (RF) down conversion Gilbert Cell mixer,
implemented in a 0.18-μm CMOS technology with a 1.8V supply, is
presented. Current bleeding (charge injection) technique has been
used to increase the conversion gain and the linearity of the mixer.
The proposed mixer provides 10.75 dB conversion gain ( C G ) with
14.3mw total power consumption. The IIP3 and 1-dB compression
point of the mixer are 8dbm and -4.6dbm respectively, at 300 MHz
IF frequencies. Comparing the current design against the
conventional mixer design, demonstrates better performance in the
conversion gain, linearity, noise figure and port-to-port isolation.
Abstract: A real-time tracking system was built to track performers on an interactive stage. Using an ordinary, up to date, desktop workstation, the performers- silhouette was segmented from the background and parameterized by calculating the normalized central image moments. In the stage system, the silhouette moments were then sent to a parallel workstation, which used them to generate corresponding 3D virtual geometry and projected the generated graphic back onto the stage.
Abstract: The paper presents an on-line recognition machine
(RM) for continuous/isolated, dynamic and static gestures that arise
in Flight Deck Officer (FDO) training. RM is based on generic pattern
recognition framework. Gestures are represented as templates using
summary statistics. The proposed recognition algorithm exploits temporal
and spatial characteristics of gestures via dynamic programming
and Markovian process. The algorithm predicts corresponding index
of incremental input data in the templates in an on-line mode.
Accumulated consistency in the sequence of prediction provides a
similarity measurement (Score) between input data and the templates.
The algorithm provides an intuitive mechanism for automatic detection
of start/end frames of continuous gestures. In the present paper,
we consider isolated gestures. The performance of RM is evaluated
using four datasets - artificial (W TTest), hand motion (Yang) and
FDO (tracker, vision-based ). RM achieves comparable results which
are in agreement with other on-line and off-line algorithms such as
hidden Markov model (HMM) and dynamic time warping (DTW).
The proposed algorithm has the additional advantage of providing
timely feedback for training purposes.