Abstract: The removal efficiency of 4-chlorophenol with
different advanced oxidation processes have been studied. Oxidation
experiments were carried out using two 4-chlorophenol
concentrations: 100 mg L-1 and 250 mg L-1 and UV generated from a
KrCl excilamp with (molar ratio H2O2: 4-chlorophenol = 25:1) and
without H2O2, and, with Fenton process (molar ratio H2O2:4-
chlorophenol of 25:1 and Fe2+ concentration of 5 mg L-1).
The results show that there is no significant difference in the 4-
chlorophenol conversion when using one of the three assayed
methods. However, significant concentrations of the photoproductos
still remained in the media when the chosen treatment involves UV
without hydrogen peroxide. Fenton process removed all the
intermediate photoproducts except for the hydroquinone and the
1,2,4-trihydroxybenzene. In the case of UV and hydrogen peroxide
all the intermediate photoproducts are removed.
Microbial bioassays were carried out utilising the naturally
luminescent bacterium Vibrio fischeri and a genetically modified
Pseudomonas putida isolated from a waste treatment plant receiving
phenolic waste. The results using V. fischeri show that with samples
after degradation, only the UV treatment showed toxicity (IC50 =38)
whereas with H2O2 and Fenton reactions the samples exhibited no
toxicity after treatment in the range of concentrations studied. Using
the Pseudomonas putida biosensor no toxicity could be detected for
all the samples following treatment due to the higher tolerance of the
organism to phenol concentrations encountered.
Abstract: In the present work, behavior of inoxydable steel as
reinforcement bar in composite concrete is being investigated. The
bar-concrete adherence in reinforced concrete (RC) beam is studied
and focus is made on the tension stiffening parameter. This study
highlighted an approach to observe this interaction behavior in
bending test instead of direct tension as per reported in many
references. The approach resembles actual loading condition of the
structural RC beam. The tension stiffening properties are then
applied to numerical finite element analysis (FEA) to verify their
correlation with laboratory results. Comparison with laboratory
shows a good correlation between the two. The experimental settings
is able to determine tension stiffening parameters in RC beam and
the modeling strategies made in ABAQUS can closely represent the
actual condition. Tension stiffening model used can represent the
interaction properties between inoxydable steel and concrete.
Abstract: This paper presents an inexpensive and effective temperature-controlled chamber for temperature environment tests of Organic Light Emitting Diode (OLED) panels. The proposed chamber is a compact warmer and cooler with an exact temperature control system. In the temperature-controlled space of the chamber, thermoelectric modules (TEMs) are utilized to cool or to heat OLED panels, novel fixtures are designed to flexibly clamp the OLED panels of different size, and special connectors for wiring between the OLED panels and the test instrument are supplied. The proposed chamber has the following features. (1) The TEMs are solid semi-conductive devices, so they operate without noise and without pollution. (2) The volume of the temperature-controlled space of the chamber about 160mm*160mm*120mm, so the chamber are compact and easy to move. (3) The range of the controlled temperatures is from -10 oC to +80 oC, and the precision is ?0.5 oC. (4) The test instrument can conveniently and easily measure the OLED panels via the novel fixtures and special connectors. In addition to a constant temperature being maintained in the chamber, a temperature shock experiments can run for a long time. Therefore, the chamber will be convenient and useful for temperature environment tests of OLED panels.
Abstract: As a part of the development of a numerical method of
close capture exhausts systems for machining devices, a test rig
recreating a situation similar to a grinding operation, but in a
perfectly controlled environment, is used. The properties of the
obtained spray of solid particles are initially characterized using
particle tracking velocimetry (PTV), in order to obtain input and
validation parameters for numerical simulations. The dispersion of a
tracer gas (SF6) emitted simultaneously with the particle jet is then
studied experimentally, as the dispersion of such a gas is
representative of that of finer particles, whose aerodynamic response
time is negligible. Finally, complete modeling of the test rig is
achieved to allow comparison with experimental results and thus to
progress towards validation of the models used to describe a twophase
flow generated by machining operation.
Abstract: This paper reports on the results of experimental
investigations of flash evaporation from superheated jet issues
vertically upward from a round straight nozzle of 81.3 mm diameter.
For the investigated range of jet superheat degree and velocity, it was
shown that flash evaporation enhances with initial temperature
increase. Due to the increase of jet inertia and subsequently the delay
of jet shattering, increase of jet velocity was found to result in
increase of evaporation "delay period". An empirical equation
predicts the jet evaporation completion height was developed, this
equation is thought to be useful in designing the flash evaporation
chamber. In attempts for enhancement of flash evaporation, use of
steel wire mesh located at short distance downstream was found
effective with no consequent pressure drop.
Abstract: Functional Magnetic Resonance Imaging(fMRI) is a
noninvasive imaging technique that measures the hemodynamic
response related to neural activity in the human brain. Event-related
functional magnetic resonance imaging (efMRI) is a form of
functional Magnetic Resonance Imaging (fMRI) in which a series of
fMRI images are time-locked to a stimulus presentation and averaged
together over many trials. Again an event related potential (ERP) is a
measured brain response that is directly the result of a thought or
perception. Here the neuronal response of human visual cortex in
normal healthy patients have been studied. The patients were asked
to perform a visual three choice reaction task; from the relative
response of each patient corresponding neuronal activity in visual
cortex was imaged. The average number of neurons in the adult
human primary visual cortex, in each hemisphere has been estimated
at around 140 million. Statistical analysis of this experiment was
done with SPM5(Statistical Parametric Mapping version 5) software.
The result shows a robust design of imaging the neuronal activity of
human visual cortex.
Abstract: The main aim of this work is to develop a model of hydrogen sulfide (H2S) separation from natural gas by using membrane separation technology. The model is developed by incorporating three diffusion mechanisms which are Knudsen, viscous and surface diffusion towards membrane selectivity and permeability. The findings from the simulation result shows that the permeability of the gas is dependent toward the pore size of the membrane, operating pressure, operating temperature as well as feed composition. The permeability of methane has the highest value for Poly (1-trimethylsilyl-1-propyne ) PTMSP membrane at pore size of 0.1nm and decreasing toward a minimum peak at pore range 1 to 1.5 nm as pore size increased before it increase again for pore size is greater than 1.5 nm. On the other hand, the permeability of hydrogen sulfide is found to increase almost proportionally with the increase of membrane pore size. Generally, the increase of pressure will increase the permeability of gas since more driving force is provided to the system while increasing of temperature would decrease the permeability due to the surface diffusion drop off effect. A corroboration of the simulation result also showed a good agreement with the experimental data.
Abstract: This paper presents the experimental results of
leakage current waveforms which appears on porcelain insulator
surface due to existence of artificial pollutants. The tests have been
done using the chemical compounds of NaCl, Na2SiO3, H2SO4, CaO,
Na2SO4, KCl, Al2SO4, MgSO4, FeCl3, and TiO2. The insulator
surface was coated with those compounds and dried. Then, it was
tested in the chamber where the high voltage was applied. Using
correspondence analysis, the result indicated that the fundamental
harmonic of leakage current was very close to the applied voltage
and third harmonic leakage current was close to the yielded leakage
current amplitude. The first harmonic power was correlated to first
harmonic amplitude of leakage current, and third harmonic power
was close to third harmonic one. The chemical compounds of H2SO4
and Na2SiO3 affected to the power factor of around 70%. Both are the
most conductive, due to the power factor drastically increase among
the chemical compounds.
Abstract: Experimental investigation has been carried out
towards understanding the complex fluid dynamics involved in the
interaction of vortical structures with zero pressure gradient boundary
layer. A laminar boundary layer is produced on the flat plate placed
in the water flume and the synthetic jet actuator is deployed on top of
the plate at a definite distance from the leading edge. The synthetic
jet actuator has been designed in such a way that the to and fro
motion of the diaphragm is maneuvered at will by varying the
operating parameters to produce the typical streamwise vortical
structures namely hairpin and tilted vortices. PIV measurements are
made on the streamwise plane normal to the plate to evaluate their
interaction with the near wall fluid.
Abstract: Three-dimensional reconstruction of small objects has
been one of the most challenging problems over the last decade.
Computer graphics researchers and photography professionals have
been working on improving 3D reconstruction algorithms to fit the
high demands of various real life applications. Medical sciences,
animation industry, virtual reality, pattern recognition, tourism
industry, and reverse engineering are common fields where 3D
reconstruction of objects plays a vital role. Both lack of accuracy and
high computational cost are the major challenges facing successful
3D reconstruction. Fringe projection has emerged as a promising 3D
reconstruction direction that combines low computational cost to both
high precision and high resolution. It employs digital projection,
structured light systems and phase analysis on fringed pictures.
Research studies have shown that the system has acceptable
performance, and moreover it is insensitive to ambient light.
This paper presents an overview of fringe projection approaches. It
also presents an experimental study and implementation of a simple
fringe projection system. We tested our system using two objects
with different materials and levels of details. Experimental results
have shown that, while our system is simple, it produces acceptable
results.
Abstract: This paper presents a model for the evaluation of
energy performance and aerodynamic forces acting on a small
straight-bladed Darrieus-type vertical axis wind turbine depending on
blade geometrical section. It consists of an analytical code coupled to
a solid modeling software, capable of generating the desired blade
geometry based on the desired blade design geometric parameters.
Such module is then linked to a finite volume commercial CFD code
for the calculation of rotor performance by integration of the
aerodynamic forces along the perimeter of each blade for a full period
of revolution.After describing and validating the computational
model with experimental data, the results of numerical simulations
are proposed on the bases of two candidate airfoil sections, that is a
classical symmetrical NACA 0021 blade profile and the recently
developed DU 06-W-200 non-symmetric and laminar blade
profile.Through a full CFD campaign of analysis, the effects of blade
geometrical section on angle of attack are first investigated and then
the overall rotor torque and power are analyzed as a function of blade
azimuthal position, achieving a numerical quantification of the
influence of airfoil geometry on overall rotor performance.
Abstract: In the present paper, we propose numerical methods for solving the Stein equation AXC - X - D = 0 where the matrix A is large and sparse. Such problems appear in discrete-time control problems, filtering and image restoration. We consider the case where the matrix D is of full rank and the case where D is factored as a product of two matrices. The proposed methods are Krylov subspace methods based on the block Arnoldi algorithm. We give theoretical results and we report some numerical experiments.
Abstract: Minor problems arising from optimizations by
welding of fixed prostheses frameworks can be identified by
macroscopic and microscopic visual inspection. The purpose of this
study was to highlight the visible discontinuities present in the laser
welds of dental Ni-Cr alloys. Ni-Cr base metal alloys designated for
fixed prostheses manufacture were selected for the experiments.
Using cast plates, preliminary tests were conducted by laser welding.
Macroscopic visual inspection was done carefully to assess the
defects of the welding rib. Electron microscopy images allowed
visualization of small discontinuities, which escapes visual
inspection. Making comparison to Ni-Cr alloys taken in the
experiment and laser welded, after visual analysis, the best welds
appear for Heraenium NA alloy.
Abstract: This paper presents a novel sinusoidal modulation
scheme that features least correlated noise and high linearity. The
modulation circuit, which is composed of a quantizer, a resonator, and
a comparator, is capable of eliminating correlated modulation noise
while doing modulation. The proposed modulation scheme combined
with the linear quadratic optimal control is applied to a single-phase
voltage source inverter and validated with the experiment results. The
experiments show that the inverter supplies stable 60Hz 110V AC
power with a total harmonic distortion of less than 1%, under the DC
input variation from 190 V to 300 V and the output power variation
from 0 to 600 W.
Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: Carbon nanotubes (CNTs) possess unique structural,
mechanical, thermal and electronic properties, and have been
proposed to be used for applications in many fields. However, to
reach the full potential of the CNTs, many problems still need to be
solved, including the development of an easy and effective
purification procedure, since synthesized CNTs contain impurities,
such as amorphous carbon, carbon nanoparticles and metal particles.
Different purification methods yield different CNT characteristics
and may be suitable for the production of different types of CNTs. In
this study, the effect of different purification chemicals on carbon
nanotube quality was investigated. CNTs were firstly synthesized by
chemical vapor deposition (CVD) of acetylene (C2H2) on a
magnesium oxide (MgO) powder impregnated with an iron nitrate
(Fe(NO3)3·9H2O) solution. The synthesis parameters were selected
as: the synthesis temperature of 800°C, the iron content in the
precursor of 5% and the synthesis time of 30 min. The liquid phase
oxidation method was applied for the purification of the synthesized
CNT materials. Three different acid chemicals (HNO3, H2SO4, and
HCl) were used in the removal of the metal catalysts from the
synthesized CNT material to investigate the possible effects of each
acid solution to the purification step. Purification experiments were
carried out at two different temperatures (75 and 120 °C), two
different acid concentrations (3 and 6 M) and for three different time
intervals (6, 8 and 15 h). A 30% H2O2 : 3M HCl (1:1 v%) solution
was also used in the purification step to remove both the metal
catalysts and the amorphous carbon. The purifications using this
solution were performed at the temperature of 75°C for 8 hours.
Purification efficiencies at different conditions were evaluated by
thermogravimetric analysis. Thermal and electrical properties of
CNTs were also determined. It was found that the obtained electrical
conductivity values for the carbon nanotubes were typical for organic
semiconductor materials and thermal stabilities were changed
depending on the purification chemicals.
Abstract: Understanding of how and where NOx formation
occurs in industrial burner is very important for efficient and clean
operation of utility burners. Also the importance of this problem is
mainly due to its relation to the pollutants produced by more burners
used widely of gas turbine in thermal power plants and glass and steel
industry.
In this article, a numerical model of an industrial burner operating
in MILD combustion is validated with experimental data.. Then
influence of air flow rate and air temperature on combustor
temperature profiles and NOX product are investigated. In order to
modification this study reports on the effects of fuel and air dilution
(with inert gases H2O, CO2, N2), and also influence of lean-premixed
of fuel, on the temperature profiles and NOX emission.
Conservation equations of mass, momentum and energy, and
transport equations of species concentrations, turbulence, combustion
and radiation modeling in addition to NO modeling equations were
solved together to present temperature and NO distribution inside the
burner.
The results shows that dilution, cause to a reduction in value of
temperature and NOX emission, and suppresses any flame
propagation inside the furnace and made the flame inside the furnace
invisible. Dilution with H2O rather than N2 and CO2 decreases further
the value of the NOX. Also with raise of lean-premix level, local
temperature of burner and the value of NOX product are decreases
because of premixing prevents local “hot spots" within the combustor
volume that can lead to significant NOx formation. Also leanpremixing
of fuel with air cause to amount of air in reaction zone is
reach more than amount that supplied as is actually needed to burn
the fuel and this act lead to limiting NOx formation
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: This paper deals with the application for contentbased
image retrieval to extract color feature from natural images
stored in the image database by segmenting the image through
clustering. We employ a class of nonparametric techniques in which
the data points are regarded as samples from an unknown probability
density. Explicit computation of the density is avoided by using the
mean shift procedure, a robust clustering technique, which does not
require prior knowledge of the number of clusters, and does not
constrain the shape of the clusters. A non-parametric technique for
the recovery of significant image features is presented and
segmentation module is developed using the mean shift algorithm to
segment each image. In these algorithms, the only user set parameter
is the resolution of the analysis and either gray level or color images
are accepted as inputs. Extensive experimental results illustrate
excellent performance.