Abstract: In this paper, groundwater seepage into Amirkabir
tunnel has been estimated using analytical and numerical methods for
14 different sections of the tunnel. Site Groundwater Rating (SGR)
method also has been performed for qualitative and quantitative
classification of the tunnel sections. The obtained results of above
mentioned methods were compared together. The study shows
reasonable accordance with results of the all methods unless for two
sections of tunnel. In these two sections there are some significant
discrepancies between numerical and analytical results mainly
originated from model geometry and high overburden. SGR and the
analytical and numerical calculations, confirm high concentration of
seepage inflow in fault zones. Maximum seepage flow into tunnel has
been estimated 0.425 lit/sec/m using analytical method and 0.628
lit/sec/m using numerical method occured in crashed zone. Based on
SGR method, six sections of 14 sections in Amirkabir tunnel axis are
found to be in "No Risk" class that is supported by the analytical and
numerical seepage value of less than 0.04 lit/sec/m.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: The wide use of the Internet-based applications bring many challenges to the researchers to guarantee the continuity of the connections needed by the mobile hosts and provide reliable Internet access for them. One of proposed solutions by Internet Engineering Task Force (IETF) is to connect the local, multi-hop, and infrastructure-less Mobile Ad hoc Network (MANET) with Internet structure. This connection is done through multi-interface devices known as Internet Gateways. Many issues are related to this connection like gateway discovery, handoff, address auto-configuration and selecting the optimum gateway when multiple gateways exist. Many studies were done proposing gateway selection schemes with a single selection criterion or weighted multiple criteria. In this research, a review of some of these schemes is done showing the differences, the features, the challenges and the drawbacks of each of them.
Abstract: The edges of low contrast images are not clearly
distinguishable to human eye. It is difficult to find the edges and
boundaries in it. The present work encompasses a new approach for
low contrast images. The Chebyshev polynomial based fractional
order filter has been used for filtering operation on an image. The
preprocessing has been performed by this filter on the input image.
Laplacian of Gaussian method has been applied on preprocessed
image for edge detection. The algorithm has been tested on two test
images.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: It has become an increasing evident that large
development influences the climate. There are concerns that rising
temperature over developed areas could have negative impact and
increase living discomfort within city boundaries. Temperature trends
in Ibadan city have received little attention, yet the area has
experienced heavy urban expansion between 1972 and 2014. This
research aims at examining the impact of landuse change on surface
temperature knowing that the built-up environment absorb and store
solar energy, resulting into the Urban Heat Island (UHI) effect. The
Landsat imagery was used to examine the landuse change for a
period of 42 years (1972-2014). Land Surface Temperature (LST)
was obtained by converting the thermal band to a surface temperature
map and zonal statistic analyses was used to examine the relationship
between landuse and temperature emission. The results showed that
the settlement area increased to a large extent while the area covered
by vegetation reduced during the study period. The spatial and
temporal trends of surface temperature are related to the gradual
change in urban landuse/landcover and the settlement area has the
highest emission. This research provides useful insight into the
temporal behavior of the Ibadan city.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: The performance and analysis of speech recognition
system is illustrated in this paper. An approach to recognize the
English word corresponding to digit (0-9) spoken by 2 different
speakers is captured in noise free environment. For feature extraction,
speech Mel frequency cepstral coefficients (MFCC) has been used
which gives a set of feature vectors from recorded speech samples.
Neural network model is used to enhance the recognition
performance. Feed forward neural network with back propagation
algorithm model is used. However other speech recognition
techniques such as HMM, DTW exist. All experiments are carried
out on Matlab.
Abstract: In this paper, an effective non-destructive, noninvasive
approach for leak detection was proposed. The process relies
on analyzing thermal images collected by an IR viewer device that
captures thermo-grams. In this study a statistical analysis of the
collected thermal images of the ground surface along the expected
leak location followed by a visual inspection of the thermo-grams
was performed in order to locate the leak. In order to verify the
applicability of the proposed approach the predicted leak location
from the developed approach was compared with the real leak
location. The results showed that the expected leak location was
successfully identified with an accuracy of more than 95%.
Abstract: Human leukocyte antigen (HLA) typing from next
generation sequencing (NGS) data has the potential for applications in
clinical laboratories and population genetic studies. Here we introduce
a novel technique for HLA typing from NGS data based on
read-mapping using a comprehensive reference panel containing all
known HLA alleles and de novo assembly of the gene-specific short
reads. An accurate HLA typing at high-digit resolution was achieved
when it was tested on publicly available NGS data, outperforming
other newly-developed tools such as HLAminer and PHLAT.
Abstract: Experimental & numeral study of temperature
distribution during milling process, is important in milling quality
and tools life aspects. In the present study the milling cross-section
temperature is determined by using Artificial Neural Networks
(ANN) according to the temperature of certain points of the work
piece and the point specifications and the milling rotational speed of
the blade. In the present work, at first three-dimensional model of the
work piece is provided and then by using the Computational Heat
Transfer (CHT) simulations, temperature in different nods of the
work piece are specified in steady-state conditions. Results obtained
from CHT are used for training and testing the ANN approach. Using
reverse engineering and setting the desired x, y, z and the milling
rotational speed of the blade as input data to the network, the milling
surface temperature determined by neural network is presented as
output data. The desired points temperature for different milling
blade rotational speed are obtained experimentally and by
extrapolation method for the milling surface temperature is obtained
and a comparison is performed among the soft programming ANN,
CHT results and experimental data and it is observed that ANN soft
programming code can be used more efficiently to determine the
temperature in a milling process.
Abstract: Unmanned Aircraft Systems (UAS) become
indispensable parts of modern airpower as force multiplier. One of
the main advantages of UAS is long endurance. UAS have to take
extra payloads to accomplish different missions but these payloads
decrease endurance of aircraft because of increasing drag. There are
continuing researches to increase the capability of UAS. There are
some vertical thermal air currents, which can cause climb and
increase endurance, in nature. Birds and gliders use thermals to gain
altitude with no effort. UAS have wide wings which can use
thermals like birds and gliders. Thermal regions, which is area of
2000-3000 meter (1 NM), exist all around the world. It is natural and
infinite source. This study analyses if thermal regions can be adopted
and implemented as an assistant tool for UAS route planning. First
and second part of study will contain information about the thermal
regions and current applications about UAS in aviation and climbing
performance with a real example. Continuing parts will analyze the
contribution of thermal regions to UAS endurance. Contribution is
important because planning declaration of UAS navigation rules will
be in 2015.
Abstract: The ultrasound imaging is very popular to diagnosis
the disease because of its non-invasive nature. The ultrasound
imaging slowly produces low quality images due to the presence of
spackle noise and wave interferences. There are several algorithms to
be proposed for the segmentation of ultrasound carotid artery images
but it requires a certain limit of user interaction. The pixel in an
image is highly correlated so the spatial information of surrounding
pixels may be considered in the process of image segmentation which
improves the results further. When data is highly correlated, one pixel
may belong to more than one cluster with different degree of
membership. There is an important step to computerize the evaluation
of arterial disease severity using segmentation of carotid artery lumen
in 2D and 3D ultrasonography and in finding vulnerable
atherosclerotic plaques susceptible to rupture which can cause stroke.
Abstract: In this research (using induction furnace process)
nodular iron with three different percentages of copper (residual,
0.5% and 1,2%) was obtained. Chemical analysis was performed by
mass spectrometry and microstructures were characterized by Optical
Microscopy (ASTM E3) and Scanning Electron Microscopy (SEM).
The study of mechanical behavior was carried out in a mechanical
test machine (ASTM E8) and a Pin on disk tribometer (ASTM G99)
was used to assess wear resistance. It is observed that the dissolution
of copper in crystal lattice increases the pearlite structure improving
the wear and hardness behavior, but producing a contrary effect on
the energy absorption.
Abstract: In this paper, we regard as a coded transmission over a
frequency-selective channel. We plan to study analytically the
convergence of the turbo-detector using a maximum a posteriori
(MAP) equalizer and a MAP decoder. We demonstrate that the
densities of the maximum likelihood (ML) exchanged during the
iterations are e-symmetric and output-symmetric. Under the Gaussian
approximation, this property allows to execute a one-dimensional
scrutiny of the turbo-detector. By deriving the analytical terminology
of the ML distributions under the Gaussian approximation, we confirm
that the bit error rate (BER) performance of the turbo-detector
converges to the BER performance of the coded additive white
Gaussian noise (AWGN) channel at high signal to noise ratio (SNR),
for any frequency selective channel.
Abstract: A quartz crystal microbalance (QCM) nanosensor was developed to detect lysozyme enzyme by functionalizing its gold surface with the attachment of poly(methacroyl-L-phenylalanine) (PMAPA) nanoparticles. PMAPA was chosen as a hydrophobic matrix. The hydrophobic nanoparticles were synthesized by micro-emulsion polymerization method. Hydrophobic QCM nanosensor was tested for real time detection of lysozyme enzyme from aqueous solution. The kinetic and affinity studies were determined by using lysozyme solutions with different concentrations. The responses related with mass (Δm) and frequency (Δf) shifts were used to evaluate adsorption properties.
Abstract: The aim of research was to define the relations
between volatile compounds, some parameters (pH, titratable acidity
(TA), total soluble solid (TSS), lactic acid bacteria count) and
consumer preference of commercial fermented milks. These relations
tend to be used for controlling and developing new fermented milk
product. Three leading commercial brands of fermented milks in
Thailand were evaluated by consumers (n=71) using hedonic scale
for four attributes (sweetness, sourness, flavour, and overall liking),
volatile compounds using headspace-solid phase microextraction
(HS-SPME) GC-MS, pH, TA, TSS and LAB count. Then the
relations were analyzed by principal component analysis (PCA). The
PCA data showed that all of four attributes liking scores were related
to each other. They were also related to TA, TSS and volatile
compounds. The related volatile compounds were mainly on
fermented produced compounds including acetic acid, furanmethanol,
furfural, octanoic acid and the volatiles known as artificial fruit
flavour (beta pinene, limonene, vanillin, and ethyl vanillin). These
compounds were provided the information about flavour addition in
commercial fermented milk in Thailand.
Abstract: This paper proposes a mathematical model and
examines the performance of an exact algorithm for a location–
transportation problems in humanitarian relief. The model determines
the number and location of distribution centers in a relief network,
the amount of relief supplies to be stocked at each distribution center
and the vehicles to take the supplies to meet the needs of disaster
victims under capacity restriction, transportation and budgetary
constraints. The computational experiments are conducted on the
various sizes of problems that are generated. Branch and bound
algorithm is applied for these problems. The results show that this
algorithm can solve problem sizes of up to three candidate locations
with five demand points and one candidate location with up to twenty
demand points without premature termination.
Abstract: IEEE 802.16 (WiMAX) aims to present high speed
wireless access to cover wide range coverage. The base station (BS)
and the subscriber station (SS) are the main parts of WiMAX.
WiMAX uses either Point-to-Multipoint (PMP) or mesh topologies.
In the PMP mode, the SSs connect to the BS to gain access to the
network. However, in the mesh mode, the SSs connect to each other
to gain access to the BS.
The main components of QoS management in the 802.16 standard
are the admission control, buffer management and packet scheduling.
In this paper, we use QualNet 5.0.2 to study the performance of
different scheduling schemes, such as WFQ, SCFQ, RR and SP when
the numbers of SSs increase. We find that when the number of SSs
increases, the average jitter and average end-to-end delay is increased
and the throughput is reduced.
Abstract: Precise capture of plantar 3D surface of the foot at the
loading gait phases on rigid substrates was found to be valuable for
the assessment of the physiology, health and problems of the feet.
Photogrammetry, a precision 3D spatial data capture technique is
suitable for this type of dynamic application. In this research, the
technique is utilised to study the plantar deformation as a result of
having a strip of kinesiology tape on the plantar surface during the
loading phase of gait. For this pilot study, one healthy adult male
subject was recruited under the University’s human research ethics
guidelines for this preliminary study. The 3D plantar deformation
data with and without applying the tape were analysed. The results
and analyses are presented together with detailed findings.