Abstract: New advancement of technology and never satisfying demands of the civilization are putting huge pressure on the natural fuel resources and these resources are at a constant threat to its sustainability. To get the best out of the automobile, the optimum balance between performance and fuel economy is important. In the present state of art, either of the above two aspects are taken into mind while designing and development process which puts the other in the loss as increase in fuel economy leads to decrement in performance and vice-versa. In-depth observation of the vehicle dynamics apparently shows that large amount of energy is lost during braking and likewise large amount of fuel is consumed to reclaim the initial state, this leads to lower fuel efficiency to gain the same performance. Current use of Kinetic Energy Recovery System is only limited to sports vehicles only because of the higher cost of this system. They are also temporary in nature as power can be squeezed only during a small time duration and use of superior parts leads to high cost, which results on concentration on performance only and neglecting the fuel economy. In this paper Kinetic Energy Recovery System for storing the power and then using the same while accelerating has been discussed. The major storing element in this system is a Flat Spiral Spring that will store energy by compression and torsion.
The use of spring ensure the permanent storage of energy until used by the driver unlike present mechanical regeneration system in which the energy stored decreases with time and is eventually lost. A combination of internal gears and spur gears will be used in order to make the energy release uniform which will lead to safe usage. The system can be used to improve the fuel efficiency by assisting in overcoming the vehicle’s inertia after braking or to provide instant acceleration whenever required by the driver. The performance characteristics of the system including response time, mechanical efficiency and overall increase in efficiency are demonstrated. This technology makes the KERS (Kinetic Energy Recovery System) more flexible and economical allowing specific application while at the same time increasing the time frame and ease of usage.
Abstract: Evolvable hardware (EHW) is a developing field that
applies evolutionary algorithm (EA) to automatically design circuits,
antennas, robot controllers etc. A lot of research has been done in this
area and several different EAs have been introduced to tackle
numerous problems, as scalability, evolvability etc. However every
time a specific EA is chosen for solving a particular task, all its
components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade the
selection of the right parameters for the EA-s components for solving
different “test-problems" has been investigated. In this paper the
behaviour of mutation rate for designing logic circuits, which has not
been done before, has been deeply analyzed. The mutation rate for an
EHW system modifies the number of inputs of each logic gates, the
functionality (for example from AND to NOR) and the connectivity
between logic gates. The behaviour of the mutation has been
analyzed based on the number of generations, genotype redundancy
and number of logic gates for the evolved circuits. The experimental
results found provide the behaviour of the mutation rate during
evolution for the design and optimization of simple logic circuits.
The experimental results propose the best mutation rate to be used for
designing combinational logic circuits. The research presented is
particular important for those who would like to implement a
dynamic mutation rate inside the evolutionary algorithm for evolving
digital circuits. The researches on the mutation rate during the last 40
years are also summarized.
Abstract: Data Warehousing tools have become very popular and currently many of them have moved to Web-based user interfaces to make it easier to access and use the tools. The next step is to enable these tools to be used within a portal framework. The portal framework consists of pages having several small windows that contain individual data warehouse query results. There are several issues that need to be considered when designing the architecture for a portal enabled data warehouse query tool. Some issues need special techniques that can overcome the limitations that are imposed by the nature of data warehouse queries. Issues such as single sign-on, query result caching and sharing, customization, scheduling and authorization need to be considered. This paper discusses such issues and suggests an architecture to support data warehouse queries within Web portal frameworks.
Abstract: Typical Intelligent Decision Support System is 4-based, its design composes of Data Warehouse, Online Analytical Processing, Data Mining and Decision Supporting based on models, which is called Decision Support System Based on Data Warehouse (DSSBDW). This way takes ETL,OLAP and DM as its implementing means, and integrates traditional model-driving DSS and data-driving DSS into a whole. For this kind of problem, this paper analyzes the DSSBDW architecture and DW model, and discusses the following key issues: ETL designing and Realization; metadata managing technology using XML; SQL implementing, optimizing performance, data mapping in OLAP; lastly, it illustrates the designing principle and method of DW in DSSBDW.
Abstract: The need for reputation assessment is particularly strong in peer-to-peer (P2P) systems because the peers' personal site autonomy is amplified by the inherent technological decentralization of the environment. However, the decentralization notion makes the problem of designing a peer-to-peer based reputation assessment substantially harder in P2P networks than in centralized settings.Existing reputation systems tackle the reputation assessment process in an ad-hoc manner. There is no systematic and coherent way to derive measures and analyze the current reputation systems. In this paper, we propose a reputation assessment process and use it to classify the existing reputation systems. Simulation experiments are conducted and focused on the different methods in selecting the recommendation sources and retrieving the recommendations. These two phases can contribute significantly to the overall performance due to communication cost and coverage.
Abstract: Video-on-demand (VOD) is designed by using content delivery networks (CDN) to minimize the overall operational cost and to maximize scalability. Estimation of the viewing pattern (i.e., the relationship between the number of viewings and the ranking of VOD contents) plays an important role in minimizing the total operational cost and maximizing the performance of the VOD systems. In this paper, we have analyzed a large body of commercial VOD viewing data and found that the viewing rank distribution fits well with the parabolic fractal distribution. The weighted linear model fitting function is used to estimate the parameters (coefficients) of the parabolic fractal distribution. This paper presents an analytical basis for designing an optimal hierarchical VOD contents distribution system in terms of its cost and performance.
Abstract: In the artificial intelligence field, knowledge
representation and reasoning are important areas for intelligent
systems, especially knowledge base systems and expert systems.
Knowledge representation Methods has an important role in
designing the systems. There have been many models for knowledge
such as semantic networks, conceptual graphs, and neural networks.
These models are useful tools to design intelligent systems. However,
they are not suitable to represent knowledge in the domains of reality
applications. In this paper, new models for knowledge representation
called computational networks will be presented. They have been
used in designing some knowledge base systems in education for
solving problems such as the system that supports studying
knowledge and solving analytic geometry problems, the program for
studying and solving problems in Plane Geometry, the program for
solving problems about alternating current in physics.
Abstract: In the present article, a new method has been developed to enhance the application of equipment monitoring, which in turn results in improving condition-based maintenance economic impact in an automobile parts manufacturing factory. This study also describes how an effective software with a simple database can be utilized to achieve cost-effective improvements in maintenance performance. The most important results of this project are indicated here: 1. 63% reduction in direct and indirect maintenance costs. 2. Creating a proper database to analyse failures. 3. Creating a method to control system performance and develop it to similar systems. 4. Designing a software to analyse database and consequently create technical knowledge to face unusual condition of the system. Moreover, the results of this study have shown that the concept and philosophy of maintenance has not been understood in most Iranian industries. Thus, more investment is strongly required to improve maintenance conditions.
Abstract: The objective of this paper is to present explicit analytical formulas for evaluating important characteristics of Double Moving Average control chart (DMA) for Poisson distribution. The most popular characteristics of a control chart are Average Run Length ( 0 ARL ) - the mean of observations that are taken before a system is signaled to be out-of control when it is actually still incontrol, and Average Delay time ( 1 ARL ) - mean delay of true alarm times. An important property required of 0 ARL is that it should be sufficiently large when the process is in-control to reduce a number of false alarms. On the other side, if the process is actually out-ofcontrol then 1 ARL should be as small as possible. In particular, the explicit analytical formulas for evaluating 0 ARL and 1 ARL be able to get a set of optimal parameters which depend on a width of the moving average ( w ) and width of control limit ( H ) for designing DMA chart with minimum of 1 ARL
Abstract: Despite the fact that Arabic language is currently one
of the most common languages worldwide, there has been only a
little research on Arabic speech recognition relative to other
languages such as English and Japanese. Generally, digital speech
processing and voice recognition algorithms are of special
importance for designing efficient, accurate, as well as fast automatic
speech recognition systems. However, the speech recognition process
carried out in this paper is divided into three stages as follows: firstly,
the signal is preprocessed to reduce noise effects. After that, the
signal is digitized and hearingized. Consequently, the voice activity
regions are segmented using voice activity detection (VAD)
algorithm. Secondly, features are extracted from the speech signal
using Mel-frequency cepstral coefficients (MFCC) algorithm.
Moreover, delta and acceleration (delta-delta) coefficients have been
added for the reason of improving the recognition accuracy. Finally,
each test word-s features are compared to the training database using
dynamic time warping (DTW) algorithm. Utilizing the best set up
made for all affected parameters to the aforementioned techniques,
the proposed system achieved a recognition rate of about 98.5%
which outperformed other HMM and ANN-based approaches
available in the literature.
Abstract: In this paper, a novel approach is presented
for designing multiplier-free state-space digital filters. The
multiplier-free design is obtained by finding power-of-2 coefficients
and also quantizing the state variables to power-of-2
numbers. Expressions for the noise variance are derived for the
quantized state vector and the output of the filter. A “structuretransformation
matrix" is incorporated in these expressions. It
is shown that quantization effects can be minimized by properly
designing the structure-transformation matrix. Simulation
results are very promising and illustrate the design algorithm.
Abstract: This paper address the network reliability optimization
problem in the optical access network design for the 3G cellular
systems. We presents a novel 0-1 integer programming model for
designing optical access network topologies comprised of multi-rings
with common-edge in order to guarantee always-on services. The
results show that the proposed model yields access network
topologies with the optimal reliablity and satisfies both network cost
limitations and traffic demand requirements.
Abstract: These Nowadays the explosion of bombs or explosive
materials such as gas and oil near or inside the buildings cause some
losses in installations and building components. This has made the
engineers to make the buildings and their components resistance
against the effects of explosion. These activities lead to provide
regulations and different methods. The above regulations are mostly
focused on the explosion effects resulting from the vehicles around
the buildings. Therefore, the explosion resulting from the vehicles
outside the buildings will be studied in this research.
In the present study, the main goals are to investigate the
explosion load effects on the structures located on the piles with the
specific quantity of plasticity and observing the permissible response
of these structures. The concentrated mass system and the spring with
two degree of freedom will be used to study the structural system.
Abstract: Exploring an autistic child in Elementary school is a
difficult task that must be fully thought out and the teachers should
be aware of the many challenges they face raising their child
especially the behavioral problems of autistic children. Hence there
arises a need for developing Artificial intelligence (AI)
Contemporary Techniques to help diagnosis to discover autistic
people.
In this research, we suggest designing architecture of expert
system that combine Cognitive Maps (CM) with Case Based
Reasoning technique (CBR) in order to reduce time and costs of
traditional diagnosis process for the early detection to discover
autistic children. The teacher is supposed to enter child's information
for analyzing by CM module. Then, the reasoning processor would
translate the output into a case to be solved a current problem by
CBR module. We will implement a prototype for the model as a
proof of concept using java and MYSQL.
This will be provided a new hybrid approach that will achieve new
synergies and improve problem solving capabilities in AI. And we
will predict that will reduce time, costs, the number of human errors
and make expertise available to more people who want who want to
serve autistic children and their families.
Abstract: The environment pollution with pesticides and heavy
metals is a recognized problem nowadays, with extension to the
global scale the tendency of amplification. Even with all the progress
in the environmental field, both in the emphasize of the effect of the
pollutants upon health, the linked studies environment-health are
insufficient, not only in Romania but all over the world also. We aim
to describe the particular situation in Romania regarding the
uncontrolled use of pesticides, to identify and evaluate the risk zones
for health and the environment in Romania, with the final goal of
designing adequate programs for reduction and control of the risk
sources. An exploratory study was conducted to determine the
magnitude of the pesticide use problem in a population living in
Saliste, a rural setting in Transylvania, Romania. The significant
stakeholders in Saliste region were interviewed and a sample from
the population living in Saliste area was selected to fill in a designed
questionnaire. All the selected participants declared that they used
pesticides in their activities for more than one purpose. They
declared they annually applied pesticides for a period of time
between 11 and 30 years, from 5 to 9 days per year on average,
mainly on crops situated at some distance from the houses but high
risk behavior was identified as the volunteers declared the use of
pesticides in the backyard gardens, near their homes, where children
were playing. The pesticide applicators did not have the necessary
knowledge about safety and exposure. The health data must be
correlated with exposure biomarkers in attempt to identify the
possible health effects of the pesticides exposure. Future plans
include educational campaigns to raise the awareness of the
population on the danger of uncontrolled use of pesticides.
Abstract: In this article a bibliography research takes place to
track down and introduce the barriers and opportunities for the
adoption of e-Governance services mainly from the side of citizen,
that is to say, the demand side. Although governments invest
continuously in producing of e-Governance services, citizens face
difficulties to adopt these services. Barriers derive and prevent them
from using e-Governance services. Barrier is anything preventing
citizens from the adoption of e-Governance services. Barriers impede
or do not allow the adoption of e-Governance services by the
citizens. If the barriers are pinpointed, it will be possible to take them
into consideration while designing e-Governance services which the
citizens are likely to use, if the obstacles are raised. The barriers will
thus be converted in opportunities that will facilitate the adoption.
Abstract: This paper will present the initial findings of a
research into distributed computer rendering. The goal of the
research is to create a distributed computer system capable of
rendering a 3D model into an MPEG-4 stream. This paper outlines
the initial design, software architecture and hardware setup for the
system.
Distributed computing means designing and implementing
programs that run on two or more interconnected computing systems.
Distributed computing is often used to speed up the rendering of
graphical imaging. Distributed computing systems are used to
generate images for movies, games and simulations.
A topic of interest is the application of distributed computing to
the MPEG-4 standard. During the course of the research, a
distributed system will be created that can render a 3D model into an
MPEG-4 stream. It is expected that applying distributed computing
principals will speed up rendering, thus improving the usefulness and
efficiency of the MPEG-4 standard
Abstract: LabVIEW and SIMULINK are two most widely used
graphical programming environments for designing digital signal
processing and control systems. Unlike conventional text-based
programming languages such as C, Cµ and MATLAB, graphical
programming involves block-based code developments, allowing a
more efficient mechanism to build and analyze control systems. In
this paper a LabVIEW environment has been employed as a
graphical user interface for monitoring the operation of a controlled
distillation column, by visualizing both the closed loop performance
and the user selected control conditions, while the column dynamics
has been modeled under the SIMULINK environment. This tool has
been applied to the PID based decoupled control of a binary
distillation column. By means of such integrated environments the
control designer is able to monitor and control the plant behavior and
optimize the response when both, the quality improvement of
distillation products and the operation efficiency tasks, are
considered.
Abstract: Regarding to the fast growth of computer, internet, and virtual learning in our country (Iran) and need computer-based learning systems and multimedia tools as an essential part of such education, designing and implementing such systems would help teach different field such as science. This paper describes the basic principle of multimedia. At the end, with a description of learning science to the infant students, the method of this system will be explained.
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.