Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: Exact solution of an unsteady flow of elastico-viscous
fluid through a porous media in a tube of spherical cross section
under the influence of constant pressure gradient has been obtained in
this paper. Initially, the flow is generated by a constant pressure
gradient. After attaining the steady state, the pressure gradient is
suddenly withdrawn and the resulting fluid motion in a tube of
spherical cross section by taking into account of the porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K) and elastico-viscosity parameter
(β), which depends on the Non-Newtonian coefficient. The flow
parameters are found to be identical with that of Newtonian case as
elastic-viscosity parameter tends to zero and porosity tends to
infinity. It is seen that the effect of elastico-viscosity parameter,
porosity parameter of the bounding surface has significant effect on
the velocity parameter.
Abstract: A Motzkin shift is a mathematical model for constraints
on genetic sequences. In terms of the theory of symbolic dynamics,
the Motzkin shift is nonsofic, and therefore, we cannot use the Perron-
Frobenius theory to calculate its topological entropy. The Motzkin
shift M(M,N) which comes from language theory, is defined to be the
shift system over an alphabet A that consists of N negative symbols,
N positive symbols and M neutral symbols. For an x in the full shift,
x will be in the Motzkin subshift M(M,N) if and only if every finite
block appearing in x has a non-zero reduced form. Therefore, the
constraint for x cannot be bounded in length. K. Inoue has shown that
the entropy of the Motzkin shift M(M,N) is log(M + N + 1). In this
paper, a new direct method of calculating the topological entropy of
the Motzkin shift is given without any measure theoretical discussion.
Abstract: In this paper, a new trend for improvement in semianalytical
method based on scale boundaries in order to solve the 2D
elastodynamic problems is provided. In this regard, only the
boundaries of the problem domain discretization are by specific subparametric
elements. Mapping functions are uses as a class of higherorder
Lagrange polynomials, special shape functions, Gauss-Lobatto-
Legendre numerical integration, and the integral form of the weighted
residual method, the matrix is diagonal coefficients in the equations
of elastodynamic issues. Differences between study conducted and
prior research in this paper is in geometry production procedure of
the interpolation function and integration of the different is selected.
Validity and accuracy of the present method are fully demonstrated
through two benchmark problems which are successfully modeled
using a few numbers of DOFs. The numerical results agree very well
with the analytical solutions and the results from other numerical
methods.
Abstract: This paper presents the details of a numerical study of
buckling and post buckling behaviour of laminated carbon fiber
reinforced plastic (CFRP) thin-walled cylindrical shell under axial
compression using asymmetric meshing technique (AMT) by
ABAQUS. AMT is considered to be a new perturbation method to
introduce disturbance without changing geometry, boundary
conditions or loading conditions. Asymmetric meshing affects both
predicted buckling load and buckling mode shapes. Cylindrical shell
having lay-up orientation [0^o/+45^o/-45^o/0^o] with radius to thickness
ratio (R/t) equal to 265 and length to radius ratio (L/R) equal to 1.5 is
analysed numerically. A series of numerical simulations
(experiments) are carried out with symmetric and asymmetric
meshing to study the effect of asymmetric meshing on predicted
buckling behaviour. Asymmetric meshing technique is employed in
both axial direction and circumferential direction separately using
two different methods, first by changing the shell element size and
varying the total number elements, and second by varying the shell
element size and keeping total number of elements constant. The
results of linear analysis (Eigenvalue analysis) and non-linear
analysis (Riks analysis) using symmetric meshing agree well with
analytical results. The results of numerical analysis are presented in
form of non-dimensional load factor, which is the ratio of buckling
load using asymmetric meshing technique to buckling load using
symmetric meshing technique. Using AMT, load factor has about 2%
variation for linear eigenvalue analysis and about 2% variation for
non-linear Riks analysis. The behaviour of load end-shortening curve
for pre-buckling is same for both symmetric and asymmetric meshing
but for asymmetric meshing curve behaviour in post-buckling
becomes extraordinarily complex. The major conclusions are:
different methods of AMT have small influence on predicted
buckling load and significant influence on load displacement curve
behaviour in post buckling; AMT in axial direction and AMT in
circumferential direction have different influence on buckling load
and load displacement curve in post-buckling.
Abstract: Parameters of flow are calculated in vaneless diffusers
with relative width 0,014–0,10. Inlet angles of flow and similarity
criteria were varied. There is information on flow separation,
boundary layer development, configuration of streamlines.
Polytrophic efficiency, loss coefficient and recovery coefficient are
used to compare effectiveness of diffusers. The sample of
optimization of narrow diffuser with conical walls is presented. Three
wide diffusers with narrowing walls are compared. The work is made
in the R&D laboratory “Gas dynamics of turbo machines” of the TU
SPb.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: Text mining techniques are generally applied for
classifying the text, finding fuzzy relations and structures in data
sets. This research provides plenty text mining capabilities. One
common application is text classification and event extraction,
which encompass deducing specific knowledge concerning incidents
referred to in texts. The main contribution of this paper is the
clarification of a concept graph generation mechanism, which is based
on a text classification and optimal fuzzy relationship extraction.
Furthermore, the work presented in this paper explains the application
of fuzzy relationship extraction and branch and bound (BB) method
to simplify the texts.
Abstract: Starting in 2020, an EU-wide CO2-limitation of
95 g/km is scheduled for the average of an OEMs passenger car fleet.
Taking that into consideration additional improvement measures of
the Diesel cycle are necessary in order to reduce fuel consumption
and emissions while boosting, or at the least, keeping performance
values at the same time.
The present article deals with the possibilities of an optimized
air/water charge air cooler, also called iCAC (indirect Charge Air
Cooler) for a Diesel passenger car amongst extreme-boundary
conditions. In this context, the precise objective was to show the
impact of improved intercooling with reference to the engine working
process (fuel consumption and NOx-emissions). Several extremeboundaries
- e.g. varying ambient temperatures or mountainous
routes - that will become very important in the near future regarding
RDE (Real Driving emissions) were subject of the investigation.
With the introduction of RDE in 2017 (EU6c measure), the
controversial NEDC (New European Driving Cycle) will belong to
the past and the OEMs will have to avoid harmful emissions in any
conceivable real life situation.
This is certainly going to lead to optimization-measurements at the
powertrain, which again is going to make the implementation of
iCACs, presently solely used for the premium class, more and more
attractive for compact class cars. The investigations showed a benefit
in FC between 1 and 3% for the iCAC in real world conditions.
Abstract: At present, the evaluation of voltage stability
assessment experiences sizeable anxiety in the safe operation of
power systems. This is due to the complications of a strain power
system. With the snowballing of power demand by the consumers
and also the restricted amount of power sources, therefore, the system
has to perform at its maximum proficiency. Consequently, the
noteworthy to discover the maximum ability boundary prior to
voltage collapse should be undertaken. A preliminary warning can be
perceived to evade the interruption of power system’s capacity. The
effectiveness of line voltage stability indices (LVSI) is differentiated
in this paper. The main purpose of the indices used is to predict the
proximity of voltage instability of the electric power system. On the
other hand, the indices are also able to decide the weakest load buses
which are close to voltage collapse in the power system. The line
stability indices are assessed using the IEEE 14 bus test system to
validate its practicability. Results demonstrated that the implemented
indices are practically relevant in predicting the manifestation of
voltage collapse in the system. Therefore, essential actions can be
taken to dodge the incident from arising.
Abstract: Solar air heater is a type of heat exchanger which
transforms solar radiation into heat energy. The thermal performance
of conventional solar air heater has been found to be poor because of
the low convective heat transfer coefficient from the absorber plate to
the air. It is attributed to the formation of a very thin boundary layer
at the absorber plate surface commonly known as viscous sub-layer.
Thermal efficiency of solar air heater can be improved by providing
the artificial roughness on absorber plate is the most efficient
technique. In this paper an attempt is made to provide artificial
roughness by incorporating inclined multiple V-ribs in the underside
of the absorber plate. 60˚V – ribs are arranged inclined to the
direction of air flow. Performance of collector estimated theoretically
and experimentally. Results of the investigation reveal that thermal
efficiency of collector with multiple V-ribs increased by 14%.
Abstract: We study the anomalous WWγ and WWZ couplings by
calculating total cross sections of two processes at the LHeC with
electron beam energy Ee=140 GeV and the proton beam energy Ep=7
TeV, and at the FCC-ep collider with the polarized electron beam
energy Ee=80 GeV and the proton beam energy Ep=50 TeV. At the
LHeC with electron beam polarization, we obtain the results for the
difference of upper and lower bounds as (0.975, 0.118) and (0.285,
0.009) for the anomalous (Δκγ, λγ) and (Δκz, λz) couplings,
respectively. As for FCC-ep collider, these bounds are obtained as
(1.101, 0.065) and (0.320, 0.002) at an integrated luminosity of
Lint=100 fb^-1.
Abstract: Exact solution of an unsteady flow of elastico-viscous
electrically conducting fluid through a porous media in a tube of
elliptical cross section under the influence of constant pressure
gradient and magnetic field has been obtained in this paper. Initially,
the flow is generated by a constant pressure gradient. After attaining
the steady state, the pressure gradient is suddenly withdrawn and the
resulting fluid motion in a tube of elliptical cross section by taking
into account of the transverse magnetic field and porosity factor of
the bounding surface is investigated. The problem is solved in twostages
the first stage is a steady motion in tube under the influence of
a constant pressure gradient, the second stage concern with an
unsteady motion. The problem is solved employing separation of
variables technique. The results are expressed in terms of a nondimensional
porosity parameter (K), magnetic parameter (m) and
elastico-viscosity parameter (β), which depends on the Non-
Newtonian coefficient. The flow parameters are found to be identical
with that of Newtonian case as elastic-viscosity parameter and
magnetic parameter tends to zero and porosity tends to infinity. It is
seen that the effect of elastico-viscosity parameter, magnetic
parameter and the porosity parameter of the bounding surface has
significant effect on the velocity parameter.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.
Abstract: This paper focuses on the dynamic behavior of
reinforced concrete (RC) slabs. Therefore, the theoretical modal
analysis was performed using two different types of boundary
conditions. Modal analysis method is the most important dynamic
analyses. The analysis would be modal case when there is no external
force on the structure. By using this method in this paper, the effects
of freely and simply supported boundary conditions on the
frequencies and mode shapes of RC square slabs are studied. ANSYS
software was employed to derive the finite element model to
determine the natural frequencies and mode shapes of the slabs.
Then, the obtained results through numerical analysis (finite element
analysis) would be compared with the exact solution. The main goal
of the research study is to predict how the boundary conditions
change the behavior of the slab structures prior to performing
experimental modal analysis. Based on the results, it is concluded
that simply support boundary condition has obvious influence to
increase the natural frequencies and change the shape of the mode
when it is compared with freely supported boundary condition of
slabs. This means that such support conditions have the direct
influence on the dynamic behavior of the slabs. Thus, it is suggested
to use free-free boundary condition in experimental modal analysis to
precisely reflect the properties of the structure. By using free-free
boundary conditions, the influence of poorly defined supports is
interrupted.
Abstract: The fuzzy composition of objects depicted in images
acquired through MR imaging or the use of bio-scanners has often
been a point of controversy for field experts attempting to effectively
delineate between the visualized objects. Modern approaches in
medical image segmentation tend to consider fuzziness as a
characteristic and inherent feature of the depicted object, instead of
an undesirable trait. In this paper, a novel technique for efficient
image retrieval in the context of images in which segmented objects
are either crisp or fuzzily bounded is presented. Moreover, the
proposed method is applied in the case of multiple, even conflicting,
segmentations from field experts. Experimental results demonstrate
the efficiency of the suggested method in retrieving similar objects
from the aforementioned categories while taking into account the
fuzzy nature of the depicted data.
Abstract: We propose a new alternative method for imposing
fluid-solid boundary conditions in simulations of Multiparticle
Collision Dynamics. Our method is based on the introduction of
an explicit potential force acting between the fluid particles and a
surface representing a solid boundary. We show that our method can
be used in simulations of plane Poiseuille flows. Important quantities
characterizing the flow and the fluid-solid interaction like the slip
coefficient at the solid boundary and the effective viscosity of the
fluid, are measured in terms of the set of independent parameters
defining the numerical implementation. We find that our method can
be used to simulate the correct hydrodynamic flow within a wide
range of values of these parameters.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: In this research article a comprehensive investigation
has been carried out to determine the effect of thermal cycle on
temperature dependent process parameters developed during gas
tungsten arc (GTA) welding of high carbon (AISI 1090) steel butt
joints. An experiment based thermal analysis has been performed to
obtain the thermal history. We have focused on different
thermophysical properties such as thermal conductivity, heat transfer
coefficient and cooling rate. Angular torch model has been utilized to
find out the surface heat flux and its variation along the fusion zone as
well as along the longitudinal direction from fusion boundary. After
welding and formation of weld pool, heat transfer coefficient varies
rapidly in the vicinity of molten weld bead and heat affected zone. To
evaluate the heat transfer coefficient near the fusion line and near the
rear end of the plate (low temperature region), established correlation
has been implemented and has been compared with empirical
correlation which is noted as coupled convective and radiation heat
transfer coefficient. Change in thermal conductivity has been
visualized by analytical model of moving point heat source. Rate of
cooling has been estimated by using 2-dimensional mathematical
expression of cooling rate and it has shown good agreement with
experimental temperature cycle. Thermophysical properties have been
varied randomly within 0 -10s time span.
Abstract: A new relative efficiency in linear model in reference is
instructed into the linear weighted regression, and its upper and lower
bound are proposed. In the linear weighted regression model, for the
best linear unbiased estimation of mean matrix respect to the
least-squares estimation, two new relative efficiencies are given, and
their upper and lower bounds are also studied.