Abstract: Eight steel reinforced concrete beams (SRC), were
fabricated and tested under earthquake type cyclic loading. The
effectiveness of intermediate stiffeners, such as mid-span stiffener and
plastic hinge zone stiffeners, in enhancing composite action and
ductility of SRC beams was investigated. The effectiveness of
strengthened beam-to-column (SBC) and weakened beam-to-column
(WBC) connections in enhancing beam ductility was also studied. It
was found that: (1) All the specimens possessed fairly high flexural
ductility and were found adequate for structures in high seismic zones.
(2) WBC connections induced stress concentration which caused extra
damage to concrete near the flange tapering zone. This extra damage
inhibited the flexural strength development and the ductility of the
specimens with WBC connections to some extent. (3) Specimens with
SBC connections demonstrated higher flexural strength and ductility
compared to specimens with WBC connections. (4) The intermediate
stiffeners, especially combination of plastic hinge zone stiffener and
mid span stiffeners, have an obvious effect in enhancing the ductility
of the beams with SBC connection.
Abstract: The Taiwan government has invested approximately
21 billion NT dollars in the construction of bicycle paths since
bicycling has gained huge popularity as a healthy leisure and
recreational activity. This study focuses on the behavior of
recreational bicyclists in Danshuei and Bali, northern Taiwan. Data
were collected from a field investigation carried out along the
Danshuei bicycle path and Bali left-bank bicycle path. A total of 578
questionnaires were gathered for data analysis. Descriptive statistics
and Chi-Square tests were used to assess bicyclists- behaviors. The
frequency shows that, in these areas, Danshuei and Bali, most
bicyclists rented bicycles, rode the bicycle path in the afternoon for
about 2 hours. The used the bicycle path one time per week. For most,
it was the first time to ride these bicycle paths. There were significant
differences in distribution of bicycle ownership, time of day, duration
of ride, ride frequency, and whether riding occurred on weekdays or
weekends. Results indicated that most bicyclists in Danshuei and Bali
were infrequent users.
Abstract: Various solar energy technologies exist and they have
different application techniques in the generation of electrical power.
The widespread use of photovoltaic (PV) modules in such
technologies has been limited by relatively high costs and low
efficiencies. The efficiency of PV panels decreases as the operating
temperatures increase. This is due to the affect of solar intensity and
ambient temperature. In this work, Computational Fluid Dynamics
(CFD) was used to model the heat transfer from a standard PV panel
and thus determine the rate of dissipation of heat. To accurately
model the specific climatic conditions of the United Arab Emirates
(UAE), a case study of a new build green building in Dubai was
used. A finned heat pipe arrangement is proposed and analyzed to
determine the improved heat dissipation and thus improved
performance efficiency of the PV panel. A prototype of the
arrangement is built for experimental testing to validate the CFD
modeling and proof of concept.
Abstract: Arenga pinnata is an abundantly natural fiber that can be used for sound proof material. However, the scientific data of acoustics properties of Arenga pinnata was not available yet. In this study the sound absorption of pure arenga pinnata was measured. The thickness of Arenga pinnata was varied in 10 mm, 20 mm, 30mm, and 40mm. This work was carried out to investigate the potential of using Arenga pinnata fiber as raw material for sound absorbing material. Impedance Tube Method was used to measure sound absorption coefficient (α). The Measurements was done in accordance with ASTM E1050-98, that is the standard test method for impedance and absorption of acoustical materials using a tube, two microphones and a digital frequency analysis system . The results showed that sound absorption coefficients of Arenga pinnata were good from 2000 Hz to 5000 Hz within the range of 0.75 – 0.90. The optimum sound absorption coefficient was obtained from the thickness of 40 mm. These results indicated that Arenga pinnata fiber is promising to be used as raw material of sound absorbing material with low cost, light, and biodegradable.
Abstract: Bootstrapping has gained popularity in different tests of hypotheses as an alternative in using asymptotic distribution if one is not sure of the distribution of the test statistic under a null hypothesis. This method, in general, has two variants – the parametric and the nonparametric approaches. However, issues on reliability of this method always arise in many applications. This paper addresses the issue on reliability by establishing a reliability measure in terms of quantiles with respect to asymptotic distribution, when this is approximately correct. The test of hypotheses used is Ftest. The simulated results show that using nonparametric bootstrapping in F-test gives better reliability than parametric bootstrapping with relatively higher degrees of freedom.
Abstract: This paper examines the role of telecommunications in sustainable development of urban, rural and remote communities in the Northern Territory of Australia through the theoretical lens of Social Capital. Social Capital is a relatively new construct and is rapidly gaining interest among policy makers, politicians and researchers as a means to both describe and understand social and economic development. Increasingly, the concept of Social Capital, as opposed to the traditional economic indicators, is seen as a more accurate measure of well-being. Whilst the essence of Social Capital is quality social relations, the concept intersects with telecommunications and Information Communications Technology (ICT) in a number of ways. The potential of ICT to disseminate information quickly, to reach vast numbers of people simultaneously and to include the previously excluded, is immense. However, the exact nature of the relationship is not clearly defined. This paper examines the nexus between social relations of mutual benefit, telecommunications access and sustainable development. A mixed methodological approach was used to test the hypothesis that No relationship exists between Social Capital and access to telecommunications services and facilities. Four communities, which included two urban, a rural and a remote Indigenous community in the Northern Territory of Australia are the focus of this research paper.
Abstract: This paper presents a model for analysis the induced voltage of transmission lines (energized) acting on neighboring distribution lines (de-energized). From environmental restrictions, 22 kV distribution lines need to be installed under 115 kV transmission lines. With the installation of the two parallel circuits like this, they make the induced voltage which can cause harm to operators. This work was performed with the ATP-EMTP modeling to analyze such phenomenon before field testing. Simulation results are used to find solutions to prevent danger to operators who are on the pole.
Abstract: Launch and recovery helicopter wind envelope for a
ship type was determined as the first step to the helicopter
qualification program. Flight deck velocities data were obtained by
means of a two components laser Doppler anemometer testing a
1/50th model in the wind tunnel stream. Full-scale flight deck
measurements were obtained on board the ship using a sonic
anemometer. Wind tunnel and full-scale measurements were
compared, showing good agreement and finally, a preliminary launch
and recovery helicopter wind envelope for this specific ship was
built.
Abstract: The characteristic bending strength (MOR) and mean
modulus of elasticity (MOE) of tropical hardwood red seraya (Shorea
spp.) plywood were determined using European Standard EN310 and
EN789. The thickness of the test specimen was 4.0mm, 7.0mm,
9.0mm, 12.0mm and 15.0mm. The experiment found that the MOR
of red seraya plywood in EN310 is about 12% to 20% and 7% to
24% higher than EN789 whereas MOE were about 28% to 41% and
30% to 36% lower than those obtained from EN 789 for test
specimens parallel and perpendicular to the grain direction. The
linear regression shows that MOR and MOE for EN789 is about 0.8
times less and 1.5 times more than EN310. The experiment also
found that the MOR and MOE of EN310 and EN789 also depend on
the wood species that used in the experiment.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.
Abstract: This research aimed to develop plasma system used in air conditioners. This developed plasma system could be installed in the air conditioners - all split type. The quality of air could be improved to be equal to present plasma system. Development processes were as follows: 1) to study the plasma system used in the air conditioners, 2) to design a plasma generator, 3) to develop the plasma generator, and 4) to test its performance in many types of the air conditioners. This plasma system was developed by AC high voltage – 14 kv with a frequency of 50 kHz. Carbon was a conductor to generate arc in air purifier system. The research was tested by installing the plasma generator in the air conditioners - wall type. Whereas, there were 3 types of installations: air flow out, air flow in, and room center. The result of the plasma generator installed in the air conditioners, split type, revealed that the air flow out installation provided the highest average of o-zone at 223 mg/h. This type of installation provided the highest efficiency of air quality improvement. Moreover, the air flow in installation and the room center installation provided the average of the o-zone at 163 mg/h and 64 mg/h, respectively.
Abstract: Von Willebrand-s disease is the most common
inherited bleeding disorder in humans, it
caused by qualitative abnormalities of the von Willebrand factor
(vWF). Our objective is to determine the prevalence of this disease at
part of the Algerian population in the East and the South by a
biological diagnosis based on specific biological tests (automated
platelet count, the bleeding time (TS), the time of cephalin + activator
(TCA), measure of the prothrombin rate (TP), vWF rate and factor
VIII rate, Molecular electrophoresis of vWF multimers in agarose gel
in the presence of SDS). Four patients of type III or severe
Willebrand-s disease were found on 200 suspect cases. All cases are
showed a deficit in vWF rate (< 5%), and factor VIII (P
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: Nowadays for algae cell ultrasonication the
longitudinal ultrasonic piezosystems are used. In this paper a
possibility of creating unique ultrasonic piezoelectric system, which
would allow reducing energy losses and concentrating this energy to
a small closed volume are proposed. The current vibrating systems
whose ultrasonic energy is concentrated inside of hollow cylinder in
which water-algae mixture is flowing. Two, three or multiply
ultrasonic composite systems to concentrate total energy into a
hollow cylinder to creating strong algae cell ultrasonication are used.
The experiments and numerical FEM analysis results using diskshaped
transducer and the first biological test results on algae cell
disruption by ultrasonication are presented as well.
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.
Abstract: The paper presents a set of guidelines for analysis of industrial embedded distributed systems and introduces a mathematical model derived from these guidelines. In this study, the author examines a set of modern communication technologies that are or possibly can be used to build communication links between the subsystems of a distributed embedded system. An investigation of these guidelines results in a algorithm for analysis of specific use cases of target technologies. A goal of the paper acts as an important base for ongoing research on comparison of communication technologies. The author describes the principles of the model and presents results of the test calculations. Practical implementation of target technologies and empirical experiment data are based on a practical experience during the design and test of specific distributed systems in Latvian market.
Abstract: Impaired fertility may be the result of indirect
consumption of anti-fertility agents through food. Monosodium
glutamate (MSG) has been widely used as food additive, flavour
enhancer and included in vaccines. This study focuses in determining
the gonadotoxic and cytotoxic effect of MSG on selected sperm
parameters such as sperm viability, sperm membrane integrity and
testes cytoarchitecture of male mice via histological examination to
determine its effect on spermatogenesis. Twenty-four Mus musculus
were randomly divided into 4 groups and given intraperitoneal
injections (IP) daily for 14 days of different MSG concentrations at
250, 500 and 1000mg/kg MSG to body weight to induce obesity.
Saline was given to control group. Mice were sacrificed and analysis
revealed abnormalities in values for sperm parameters and damages
to testes cytoarchitecture of male mice. The results recorded
decreased viability (p0.05) with degenerative structures in seminiferous tubule of
testes. The results indicated various implications of MSG on male
mice reproductive system which has consequences in fertility
potential.
Abstract: Simulation is a very helpful and valuable work tool in
manufacturing. It can be used in industrial field allowing the
system`s behavior to be learnt and tested. Simulation provides a low
cost, secure and fast analysis tool. It also provides benefits, which
can be reached with many different system configurations. Topics to
be discussed include: Applications, Modeling, Validating, Software
and benefits of simulation. This paper provides a comprehensive
literature review on research efforts in simulation.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: Verification of real-time software systems can be
expensive in terms of time and resources. Testing is the main method
of proving correctness but has been shown to be a long and time
consuming process. Everyday engineers are usually unwilling to
adopt formal approaches to correctness because of the overhead
associated with developing their knowledge of such techniques.
Performance modelling techniques allow systems to be evaluated
with respect to timing constraints. This paper describes PARTES, a
framework which guides the extraction of performance models from
programs written in an annotated subset of C.