Abstract: The chemical degradation of dieldrin in ferric
sulfide and iron powder aqueous suspension was investigated
in laboratory batch type experiments. To identify the reaction
mechanism, reduced copper was used as reductant. More than
90% of dieldrin was degraded using both reaction systems after
29 days. Initial degradation rate of the pesticide using ferric
sulfide was superior to that using iron powder. The reaction
schemes were completely dissimilar even though the ferric ion
plays an important role in both reaction systems. In the case of
metallic iron powder, dieldrin undergoes partial dechlorination.
This reaction proceeded by reductive hydrodechlorination with
the generation of H+, which arise by oxidation of ferric iron.
This reductive reaction was accelerated by reductant but
mono-dechlorination intermediates were accumulated. On the
other hand, oxidative degradation was observed in the reaction
with ferric sulfide, and the stable chemical structure of dieldrin
was decomposed into water-soluble intermediates. These
reaction intermediates have no chemical structure of drin class.
This dehalogenation reaction assumes to occur via the adsorbed
hydroxyl radial generated on the surface of ferric sulfide.
Abstract: Software reliability prediction gives a great opportunity to measure the software failure rate at any point throughout system test. A software reliability prediction model provides with the technique for improving reliability. Software reliability is very important factor for estimating overall system reliability, which depends on the individual component reliabilities. It differs from hardware reliability in that it reflects the design perfection. Main reason of software reliability problems is high complexity of software. Various approaches can be used to improve the reliability of software. We focus on software reliability model in this article, assuming that there is a time redundancy, the value of which (the number of repeated transmission of basic blocks) can be an optimization parameter. We consider given mathematical model in the assumption that in the system may occur not only irreversible failures, but also a failure that can be taken as self-repairing failures that significantly affect the reliability and accuracy of information transfer. Main task of the given paper is to find a time distribution function (DF) of instructions sequence transmission, which consists of random number of basic blocks. We consider the system software unreliable; the time between adjacent failures has exponential distribution.
Abstract: Complex networks have been intensively studied across
many fields, especially in Internet technology, biological engineering,
and nonlinear science. Software is built up out of many interacting
components at various levels of granularity, such as functions, classes,
and packages, representing another important class of complex networks.
It can also be studied using complex network theory. Over the
last decade, many papers on the interdisciplinary research between
software engineering and complex networks have been published.
It provides a different dimension to our understanding of software
and also is very useful for the design and development of software
systems. This paper will explore how to use the complex network
theory to analyze software structure, and briefly review the main
advances in corresponding aspects.
Abstract: The recycling of concrete, bricks and masonry rubble
as concrete aggregates is an important way to contribute to a
sustainable material flow. However, there are still various
uncertainties limiting the widespread use of Recycled Concrete
Aggregates (RCA). The fluctuations in the composition of grade
recycled aggregates and their influence on the properties of fresh and
hardened concrete are of particular concern regarding the use of
RCA. Most of problems occurring while using recycled concrete
aggregates as aggregates are due to higher porosity and hence higher
water absorption, lower mechanical strengths, residual impurities on
the surface of the RCA forming weaker bond between cement paste
and aggregate. So, the reuse of RCA is still limited. Efficient
polymer based treatment is proposed in order to reuse RCA easier.
The silicon-based polymer treatments of RCA were carried out and
were compared. This kind of treatment can improve the properties of
RCA such as the rate of water absorption on treated RCA is
significantly reduced.
Abstract: According to the statistics, the prevalence of congenital hearing loss in Taiwan is approximately six thousandths; furthermore, one thousandths of infants have severe hearing impairment. Hearing ability during infancy has significant impact in the development of children-s oral expressions, language maturity, cognitive performance, education ability and social behaviors in the future. Although most children born with hearing impairment have sensorineural hearing loss, almost every child more or less still retains some residual hearing. If provided with a hearing aid or cochlear implant (a bionic ear) timely in addition to hearing speech training, even severely hearing-impaired children can still learn to talk. On the other hand, those who failed to be diagnosed and thus unable to begin hearing and speech rehabilitations on a timely manner might lose an important opportunity to live a complete and healthy life. Eventually, the lack of hearing and speaking ability will affect the development of both mental and physical functions, intelligence, and social adaptability. Not only will this problem result in an irreparable regret to the hearing-impaired child for the life time, but also create a heavy burden for the family and society. Therefore, it is necessary to establish a set of computer-assisted predictive model that can accurately detect and help diagnose newborn hearing loss so that early interventions can be provided timely to eliminate waste of medical resources. This study uses information from the neonatal database of the case hospital as the subjects, adopting two different analysis methods of using support vector machine (SVM) for model predictions and using logistic regression to conduct factor screening prior to model predictions in SVM to examine the results. The results indicate that prediction accuracy is as high as 96.43% when the factors are screened and selected through logistic regression. Hence, the model constructed in this study will have real help in clinical diagnosis for the physicians and actually beneficial to the early interventions of newborn hearing impairment.
Abstract: Building intelligent traffic guide systems has been an
interesting subject recently. A good system should be able to observe
all important visual information to be able to analyze the context of
the scene. To do so, signs in general, and traffic signs in particular,
are usually taken into account as they contain rich information to
these systems. Therefore, many researchers have put an effort on
sign recognition field. Sign localization or sign detection is the most
important step in the sign recognition process. This step filters out
non informative area in the scene, and locates candidates in later
steps. In this paper, we apply a new approach in detecting sign
locations using a new color invariant model. Experiments are carried
out with different datasets introduced in other works where authors
claimed the difficulty in detecting signs under unfavorable imaging
conditions. Our method is simple, fast and most importantly it gives
a high detection rate in locating signs.
Abstract: Retention in the IT profession is critical for
organizations to stay competitive and operate reliably in the dynamic
business environment. Most organizations rely on compensation and
rewards as primary tools to enhance retention of employees. In this
quantitative survey-based study conducted at a large global bank, we
analyze the perceptions of 575 information technology (IT) software
professionals in India and Malaysia and find that fairness of rewards
has very little impact on retention likelihood. It is far more important
to actively involve employees in organizational activities. In
addition, our findings indicate that involvement is far more important
than information flow: the typical organizational communication to
keep employees informed.
Abstract: This paper presents reliability evaluation techniques
which are applied in distribution system planning studies and
operation. Reliability of distribution systems is an important issue in
power engineering for both utilities and customers. Reliability is a
key issue in the design and operation of electric power distribution
systems and load. Reliability evaluation of distribution systems has
been the subject of many recent papers and the modeling and
evaluation techniques have improved considerably.
Abstract: Fip-gts, an immunomodulatory protein purified from Ganoderma tsugae, has been reported to possess therapeutic effects in the treatment of cancer and autoimmune disease. For medicinal application, a recombinant Fip-gts was successfully expressed and purified in Sf21 insect cells by our previously work. It is important to evaluate the immunomodulatory activity of the rFip-gts. To assess the immunomodulatory potential of rFip-gts, the T lymphocytes of murine splenocytes were used in the present study. Results revealed that rFip-gts induced cellular aggregation formation. Additionally, the expression of IL-2 and IFN-r were up-regulated after the treatment of rFip-gts, and a corresponding increased production of IL-2 and IFN-r in a dose-dependent manner. The results showed that rFip-gts has an immunomodulatory activity in inducing Th1 lymphocytes from murine splenocytes released IL-2 and IFN-γ, thus suggest that rFip-gts may have therapeutic potential in vivo as an immune modulator.
Abstract: This research aims to examine the key success factors
for the diffusion of mobile entertainment services in Malaysia. The
drivers and barriers observed in this research include perceived
benefit; concerns pertaining to pricing, product and technological
standardization, privacy and security; as well as influences from
peers and community. An analysis of a Malaysian survey of 384
respondents between 18 to 25 years shows that subscribers placed
greater importance on perceived benefit of mobile entertainment
services compared to other factors. Results of the survey also show
that there are strong positive correlations between all the factors,
with pricing issue–perceived benefit showing the strongest
relationship. This paper aims to provide an extensive study on the
drivers and barriers that could be used to derive architecture for
entertainment service provision to serve as a guide for telcos to
outline suitable approaches in order to encourage mass market
adoption of mobile entertainment services in Malaysia.
Abstract: One important objective in Precision Agriculture is to minimize the volume of herbicides that are applied to the fields through the use of site-specific weed management systems. In order to reach this goal, two major factors need to be considered: 1) the similar spectral signature, shape and texture between weeds and crops; 2) the irregular distribution of the weeds within the crop's field. This paper outlines an automatic computer vision system for the detection and differential spraying of Avena sterilis, a noxious weed growing in cereal crops. The proposed system involves two processes: image segmentation and decision making. Image segmentation combines basic suitable image processing techniques in order to extract cells from the image as the low level units. Each cell is described by two area-based attributes measuring the relations among the crops and the weeds. From these attributes, a hybrid decision making approach determines if a cell must be or not sprayed. The hybrid approach uses the Support Vector Machines and the Fuzzy k-Means methods, combined through the fuzzy aggregation theory. This makes the main finding of this paper. The method performance is compared against other available strategies.
Abstract: with increasing circuits- complexity and demand to
use portable devices, power consumption is one of the most
important parameters these days. Full adders are the basic block of
many circuits. Therefore reducing power consumption in full adders
is very important in low power circuits. One of the most powerconsuming
modules in full adders is XOR/XNOR circuit. This paper
presents two new full adders based on two new logic approaches. The
proposed logic approaches use one XOR or XNOR gate to implement
a full adder cell. Therefore, delay and power will be decreased. Using
two new approaches and two XOR and XNOR gates, two new full
adders have been implemented in this paper. Simulations are carried
out by HSPICE in 0.18μm bulk technology with 1.8V supply voltage.
The results show that the ten-transistors proposed full adder has 12%
less power consumption and is 5% faster in comparison to MB12T
full adder. 9T is more efficient in area and is 24% better than similar
10T full adder in term of power consumption. The main drawback of
the proposed circuits is output threshold loss problem.
Abstract: It is quite essential to form dialogue mechanisms and
dialogue channels to solve intercultural communication issues.
Therefore, every country should develop a intercultural education
project which aims to resolve international communication issues.
For proper mediation training, the first step is to reach an agreement
on the actors to run the project. The strongest mediation mechanisms
in the world should be analyzed and initiated within the educational
policies. A communication-based mediation model should be
developed for international mediation training. Mediators can use
their convincing communication skills as a part of this model. At the
first, fundamental stages of the mediation training should be specified
within the scope of the model. Another important topic at this point is
common sence and peace leaders to act as an ombudsman in this
process. Especially for solving some social issues and conflicts,
common sense leaders acting as an ombudsman would lead to
effective communication. In mediation training that is run by
universities and non-governmental organizations, another phase is to
focus on conducting the meetings. In intercultural mediation training,
one of the most critical topics is to conduct the meeting traffic and
performing a shuttle diplomacy. Meeting traffic is where the mediator
organizes meetings with the parties with initiative powers, in order to
contribute to the solution of the issue, and schedule these meetings.
In this notice titled “ Intercultural mediation training and the training
process of common sense leaders by the leadership of universities
communication and artistic campaigns" , communication models and
strategies about this topic will be constructed and an intercultural art
activities and perspectives will be presented.
Abstract: The malfunction of thermal protection system (TPS) caused by aerodynamic heating is a latent trouble to aircraft structure safety. Accurately predicting the structure temperature field is quite important for the TPS design of hypersonic vehicle. Since Thornton’s work in 1988, the coupled method of aerodynamic heating and heat transfer has developed rapidly. However, little attention has been paid to the influence of structural deformation on aerodynamic heating and structural temperature field. In the flight, especially the long-endurance flight, the structural deformation, caused by the aerodynamic heating and temperature rise, has a direct impact on the aerodynamic heating and structural temperature field. Thus, the coupled interaction cannot be neglected. In this paper, based on the method of static aero-thermo-elasticity, considering the influence of aero-thermo-elasticity deformation, the aerodynamic heating and heat transfer coupled results of hypersonic vehicle wing model were calculated. The results show that, for the low-curvature region, such as fuselage or center-section wing, structure deformation has little effect on temperature field. However, for the stagnation region with high curvature, the coupled effect is not negligible. Thus, it is quite important for the structure temperature prediction to take into account the effect of elastic deformation. This work has laid a solid foundation for improving the prediction accuracy of the temperature distribution of aircraft structures and the evaluation capacity of structural performance.
Abstract: Y chromosome microdeletions are the most common
genetic cause of male infertility and screening for these
microdeletions in azoospermic or severely oligospermic men is now
standard practice. Analysis of the Y chromosome in men with
azoospermia or severe oligozoospermia has resulted in the
identification of three regions in the euchromatic part of the long arm
of the human Y chromosome (Yq11) that are frequently deleted in
men with otherwise unexplained spermatogenic failure. PCR analysis
of microdeletions in the AZFa, AZFb and AZFc regions of the
human Y chromosome is an important screening tool. The aim of this
study was to analyse the type of microdeletions in men with fertility
disorders in Slovakia. We evaluated 227 patients with azoospermia
and with normal karyotype. All patient samples were analyzed
cytogenetically. For PCR amplification of sequence-tagged sites
(STS) of the AZFa, AZFb and AZFc regions of the Y chromosome
was used Devyser AZF set. Fluorescently labeled primers for all
markers in one multiplex PCR reaction were used and for automated
visualization and identification of the STS markers we used genetic
analyzer ABi 3500xl (Life Technologies). We reported 13 cases of
deletions in the AZF region 5,73%. Particular types of deletions were
recorded in each region AZFa,b,c .The presence of microdeletions in
the AZFc region was the most frequent. The study confirmed that
percentage of microdeletions in the AZF region is low in Slovak
azoospermic patients, but important from a prognostic view.
Abstract: This paper describes a method to measure and
compensate a 4 axes ultra-precision machine tool that generates micro
patterns on the large surfaces. The grooving machine is usually used
for making a micro mold for many electrical parts such as a light guide
plate for LCD and fuel cells. The ultra precision machine tool has three
linear axes and one rotational table. Shaping is usually used to
generate micro patterns. In the case of 50 μm pitch and 25 μm height
pyramid pattern machining with a 90° wedge angle bite, one of linear
axis is used for long stroke motion for high cutting speed and other
linear axis are used for feeding. The triangular patterns can be
generated with many times of long stroke of one axis. Then 90°
rotation of work piece is needed to make pyramid patterns with
superposition of machined two triangular patterns.
To make a two dimensional positioning error, straightness of two
axes in out of plane, squareness between the each axis are important.
Positioning errors, straightness and squarness were measured by laser
interferometer system. Those were compensated and confirmed by
ISO230-6. One of difficult problem to measure the error motions is
squareness or parallelism of axis between the rotational table and
linear axis. It was investigated by simultaneous moving of rotary table
and XY axes. This compensation method is introduced in this paper.
Abstract: The mixed oxide nuclear fuel (MOX) of U and Pu contains several percent of fission products and minor actinides, such as neptunium, americium and curium. It is important to determine accurately the decay heat from Curium isotopes as they contribute significantly in the MOX fuel. This heat generation can cause samples to melt very quickly if excessive quantities of curium are present. In the present paper, we introduce a new approach that can predict the decay heat from curium isotopes. This work is a part of the project funded by King Abdulaziz City of Science and Technology (KASCT), Long-Term Comprehensive National Plan for Science, Technology and Innovations, and take place in King Abdulaziz University (KAU), Saudi Arabia. The approach is based on the numerical solution of coupled linear differential equations that describe decays and buildups of many nuclides to calculate the decay heat produced after shutdown. Results show the consistency and reliability of the approach applied.
Abstract: This study realizes an empirical investigation of main factors to develop an accounting career, stereotypes on accountants and accounting and perceptions on future career path for a sample of master students in accounting. The research provides some insight into what master students consider when choosing their future career paths. The most important two reasons chosen by students were “career opportunities" and “future earnings. They see accounting as structured, governed by conformity, requiring skills in working with numbers, monotonous, accurate, more efficient than effective but also absorbing, interesting and involving a certain degree of novelty. Although these students plan to start their careers in a multinational or accounting/audit firm, most of those plan to leave after five years. It resulted that women value more flexibility and time requiring special attention in retention policies practiced by firms.
Abstract: In 1990 [1] the subband-DFT (SB-DFT) technique was proposed. This technique used the Hadamard filters in the decomposition step to split the input sequence into low- and highpass sequences. In the next step, either two DFTs are needed on both bands to compute the full-band DFT or one DFT on one of the two bands to compute an approximate DFT. A combination network with correction factors was to be applied after the DFTs. Another approach was proposed in 1997 [2] for using a special discrete wavelet transform (DWT) to compute the discrete Fourier transform (DFT). In the first step of the algorithm, the input sequence is decomposed in a similar manner to the SB-DFT into two sequences using wavelet decomposition with Haar filters. The second step is to perform DFTs on both bands to obtain the full-band DFT or to obtain a fast approximate DFT by implementing pruning at both input and output sides. In this paper, the wavelet-based DFT (W-DFT) with Haar filters is interpreted as SB-DFT with Hadamard filters. The only difference is in a constant factor in the combination network. This result is very important to complete the analysis of the W-DFT, since all the results concerning the accuracy and approximation errors in the SB-DFT are applicable. An application example in spectral analysis is given for both SB-DFT and W-DFT (with different filters). The adaptive capability of the SB-DFT is included in the W-DFT algorithm to select the band of most energy as the band to be computed. Finally, the W-DFT is extended to the two-dimensional case. An application in image transformation is given using two different types of wavelet filters.
Abstract: Subgrade moisture content varies with environmental and soil conditions and has significant influence on pavement performance. Therefore, it is important to establish realistic estimates of expected subgrade moisture contents to account for the effects of this variable on predicted pavement performance during the design stage properly. The initial boundary soil suction profile for a given pavement is a critical factor in determining expected moisture variations in the subgrade for given pavement and climatic and soil conditions. Several numerical models have been developed for predicting water and solute transport in saturated and unsaturated subgrade soils. Soil hydraulic properties are required for quantitatively describing water and chemical transport processes in soils by the numerical models. The required hydraulic properties are hydraulic conductivity, water diffusivity, and specific water capacity. The objective of this paper was to determine isothermal moisture profiles in a soil fill and predict the soil moisture movement above the ground water table using a simple one-dimensional finite difference model.