Abstract: In this paper, the dependence of soliton pulses with
respect to phase in a 10Gbps, single channel, dispersion
uncompensated telecommunication system was studied. The
characteristic feature of periodic soliton interaction was noted at the
Interaction point (I=6202.5Km) in one collision length of L=12405.1
Km. The interaction point is located for 10Gbps system with an
initial relative spacing (qo) of soliton as 5.28 using Perturbation
theory. It is shown that, when two in-phase solitons are launched,
they interact at the point I=6202.5 Km, but the interaction could be
restricted with introduction of different phase initially. When the
phase of the input solitons increases, the deviation of soliton pulses at
the ‘I’ also increases. We have successfully demonstrated this effect
in a telecommunication set-up in terms of Quality factor (Q), where
the Q=0 for in-phase soliton. The Q was noted to be 125.9, 38.63,
47.53, 59.60, 161.37, and 78.04 for different phases such as 10o, 20o,
30o, 45o, 60o and 90o degrees respectively at Interaction point (I).
Abstract: Community integration is a construct that an
increasing body of research has shown to have a significant impact
on the wellbeing and recovery of people with psychiatric problems.
However, there are few studies that explore which factors can be
associated and predict community integration. Moreover, community
integration has been mostly studied in minority groups, and current
literature on the definition and manifestation of community
integration in the general population is scarcer. Thus, the current
study aims to characterize community integration and explore
possible predictor variables in a sample of participants with
psychiatric problems (PP, N=183) and a sample of participants from
the general population (GP, N=211).
Results show that people with psychiatric problems present above
average values of community integration, but are significantly lower
than their healthy counterparts. It was also possible to observe that
community integration does not vary in terms of the sociodemographic
characteristics of both groups in this study. Correlation
and multiple regression showed that, among several variables that
literature present as relevant in the community integration process,
only three variables emerged as having the most explanatory value in
community integration of both groups: sense of community, basic
needs satisfaction and submission. These results also shown that
those variables have increased explanatory power in the PP sample,
which leads us to emphasize the need to address this issue in future
studies and increase the understanding of the factors that can be
involved in the promotion of community integration, in order to
devise more effective interventions in this field.
Abstract: Paranoid ideation is a common thought process that
constitutes a defense against perceived social threats. The current
study aimed at the characterization of paranoid ideation in youths and
to explore the possible predictors involved in the development of
paranoid ideations. Paranoid ideation, shame, submission, early
childhood memories and current depressive, anxious and stress
symptomatology were assessed in a sample of 1516 Portuguese
youths. Higher frequencies of paranoid ideation were observed,
particularly in females and youths from lower socioeconomic status.
The main predictors identified relates to submissive behaviors and
adverse childhood experiences, and especially to shame feelings. The
current study emphasizes that the these predictors are similar to
findings in adults and clinical populations, and future implications to
research and clinical practice aiming at paranoid ideations are
discussed, as well as the pertinence of the study of mediating factors
that allow a wider understanding of this thought process in younger
populations and the prevention of psychopathology in adulthood.
Abstract: WO3/SiO2 catalysts were modified by an ion exchange
method with sodium hydroxide or potassium hydroxide solution. The
performance of the modified catalysts was tested in the metathesis of
ethylene and trans-2-butene to propylene. During ion exchange,
sodium and potassium ions played different roles. Sodium modified
catalysts revealed constant trans-2-butene conversion and propylene
selectivity when the concentrations of sodium in the solution were
varied. In contrast, potassium modified catalysts showed reduction of
the conversion and increase of the selectivity. From these results,
potassium hydroxide may affect the transformation of tungsten oxide
active species, resulting in the decrease in conversion whereas
sodium hydroxide did not. Moreover, the modification of catalysts by
this method improved the catalyst stability by lowering the amount of
coke deposited on the catalyst surface.
Abstract: The substantial development of the construction
industry has forced the cement industry, its major support, to focus
on achieving maximum productivity to meet the growing demand for
this material. This means that the reliability of a cement production
system needs to be at the highest level that can be achieved by good
maintenance. This paper studies the extent to which the
implementation of RCM is needed as a strategy for increasing the
reliability of the production systems component can be increased,
thus ensuring continuous productivity. In a case study of four Libyan
cement factories, 80 employees were surveyed and 12 top and middle
managers interviewed. It is evident that these factories usually
breakdown more often than once per month which has led to a
decline in productivity. In many times they cannot achieve the
minimum level of production amount. This has resulted from the
poor reliability of their production systems as a result of poor or
insufficient maintenance. It has been found that most of the factories’
employees misunderstand maintenance and its importance. The main
cause of this problem is the lack of qualified and trained staff, but in
addition it has been found that most employees are not found to be
motivated as a result of a lack of management support and interest. In
response to these findings, it has been suggested that the RCM
strategy should be implemented in the four factories. The results
show the importance of the development of maintenance strategies
through the implementation of RCM in these factories. The purpose
of it would be to overcome the problems that could secure the
reliability of the production systems. This study could be a useful
source of information for academic researchers and the industrial
organizations which are still experiencing problems in maintenance
practices.
Abstract: Microbes have been used to solve environmental
problems for many years. The role of microorganism to sequester,
precipitate or alter the oxidation state of various heavy metals has
been extensively studied. Treatment using microorganism interacts
with toxic metal are very diverse. The purpose of this research is to
remove the mercury using Pseudomonas putida (P. putida), pure
culture ATTC 49128 at optimum growth parameters such as
techniques of culture, acclimatization time and speed of incubator
shaker. Thus, in this study, the optimum growth parameters of P.
putida were obtained to achieve the maximum of mercury removal.
Based on the optimum parameters of P. putida for specific growth
rate, the removal of two different mercury concentration, 1 ppm and
4 ppm were studied. From mercury nitrate solution, a mercuryresistant
bacterial strain which is able to reduce from ionic mercury
to metallic mercury was used to reduce ionic mercury. The overall
levels of mercury removal in this study were between 80% and 89%.
The information obtained in this study is of fundamental for
understanding of the survival of P. putida ATTC 49128 in mercury
solution. Thus, microbial mercury removal is a potential
bioremediation for wastewater especially in petrochemical industries
in Malaysia.
Abstract: In contrast with literal meaning of nano, researchers
have been achieved mega adventures in this area and every day more
nanomaterials are being introduced to the market. After long time
application of fossil-based plastics, nowadays accumulation of their
waste seems to be a big problem to the environment. On the other
hand, mankind has more attention to safety and living environment.
Replacing common plastic packaging materials with degradable ones
that degrade faster and convert to non-dangerous components like
water and carbon dioxide have more attractions; these new materials
are based on renewable and inexpensive sources of starch and
cellulose. However, the functional properties of them do not suitable
for packaging. At this point, nanotechnology has an important role.
Utilizing of nanomaterials in polymer structure will improve
mechanical and physical properties of them; nanocrystalline cellulose
(NCC) has this ability. This work has employed a chemical method to
produce NCC and starch bio nanocomposite containing NCC. X-Ray
Diffraction technique has characterized the obtained materials.
Results showed that applied method is a suitable one as well as
applicable one to NCC production.
Abstract: Five palm oil ether monoesters utilized as novel
biodiesels were synthesized and structurally identified in the paper.
The investigation was made on the effect of ether species on
physicochemical properties of the palm oil ether monoesters. The
results showed that density, kinematic viscosity, smoke point, and
solidifying point increase linearly with their –CH2 group number in
certain relationships. Cetane number is enhanced whereas heat value
decreases linearly with –CH2 group number. In addition, the
influencing regularities of the volumetric content of the palm oil ether
monoesters on the fuel properties were also studied when the ether
monoesters are used as diesel fuel additives.
Abstract: This paper deals with the study of reflection and
transmission characteristics of acoustic waves at the interface of a
semiconductor half-space and elastic solid. The amplitude ratios
(reflection and transmission coefficients) of reflected and transmitted
waves to that of incident wave varying with the incident angles have
been examined for the case of quasi-longitudinal wave. The special
cases of normal and grazing incidence have also been derived with
the help of Gauss elimination method. The mathematical model
consisting of governing partial differential equations of motion and
charge carriers’ diffusion of n-type semiconductors and elastic solid
has been solved both analytically and numerically in the study. The
numerical computations of reflection and transmission coefficients
has been carried out by using MATLAB programming software for
silicon (Si) semiconductor and copper elastic solid. The computer
simulated results have been plotted graphically for Si
semiconductors. The study may be useful in semiconductors,
geology, and seismology in addition to surface acoustic wave (SAW)
devices.
Abstract: Toddy sediment (TS) was cultured in a PDA medium
to determine initial yeast load, and also it was undergone sun, shade,
solar, dehumidified cold air (DCA) and hot air oven (at 400, 500 and
60oC) drying with a view to preserve viability of yeast. Thereafter,
this study was conducted according to two factor factorial design in
order to determine best preservation method. Therein the dried TS
from the best drying method was taken and divided into two portions.
One portion was mixed with 3: 7 ratio of TS: rice flour and the
mixture was divided in to two again. While one portion was kept
under in house condition the other was in a refrigerator. Same
procedure was followed to the rest portion of TS too but it was at the
same ratio of corn flour. All treatments were vacuum packed in triple
laminate pouches and the best preservation method was determined
in terms of leavening index (LI). The TS obtained from the best
preservation method was used to make foods (bread and hopper) and
organoleptic properties of it were evaluated against same of ordinary
foods using sensory panel with a five point hedonic scale.
Results revealed that yeast load or fresh TS was 58×106 CFU/g.
The best drying method in preserving viability of yeast was DCA
because LI of this treatment (96%) is higher than that of other three
treatments. Organoleptic properties of foods prepared from best
preservation method are as same as ordinary foods according to Duo
trio test.
Abstract: New design of three dimensional (3D) flywheel system
based on gimbal and gyro mechanics is proposed. The 3D flywheel
device utilizes the rotational motion of three spherical shells and the
conservation of angular momentum to achieve planar locomotion.
Actuators mounted to the ring-shape frames are installed within the
system to drive the spherical shells to rotate, for the purpose of steering
and stabilization. Similar to the design of 2D flywheel system, it is
expected that the spherical shells may function like a “flyball” to store
and supply mechanical energy; additionally, in comparison with
typical single-wheel and spherical robots, the 3D flywheel can be used
for developing omnidirectional robotic systems with better mobility.
The Lagrangian method is applied to derive the equation of motion of
the 3D flywheel system, and simulation studies are presented to verify
the proposed design.
Abstract: Pneumatic reactors have been widely employed in various sectors of the chemical industry, especially where are required high heat and mass transfer rates. This study aimed to obtain correlations that allow the prediction of gas hold-up (Ԑ) and volumetric oxygen transfer coefficient (kLa), and compare these values, for three models of pneumatic reactors on two scales utilizing Newtonian fluids. Values of kLa were obtained using the dynamic pressure-step method, while e was used for a new proposed measure. Comparing the three models of reactors studied, it was observed that the mass transfer was superior to draft-tube airlift, reaching e of 0.173 and kLa of 0.00904s-1. All correlations showed good fit to the experimental data (R2≥94%), and comparisons with correlations from the literature demonstrate the need for further similar studies due to shortage of data available, mainly for airlift reactors and high viscosity fluids.
Abstract: This paper examines the system protection for cyber-physical
systems (CPS). CPS are particularly characterized by their
networking system components. This means they are able to adapt to
the needs of their users and its environment. With this ability, CPS
have new, specific requirements on the protection against anti-counterfeiting,
know-how loss and manipulation. They increase the
requirements on system protection because piracy attacks can be
more diverse, for example because of an increasing number of
interfaces or through the networking abilities. The new requirements
were identified and in a next step matched with existing protective
measures. Due to the found gap the development of new protection
measures has to be forced to close this gap. Moreover a comparison
of the effectiveness between selected measures was realized and the
first results are presented in this paper.
Abstract: The effect of partially substitution of magnetic
impurity Fe for Cu to the magnetic and transport properties in
electron-doped superconducting cuprates of
Eu1.85+yCe0.15-yCu1-yFeyO4+α-δ (ECCFO) with y = 0, 0.010, 0.020, and
0.050 has been studied, in order to investigate the mechanism of
magnetic and transport properties of ECCFO in normal-state.
Magnetic properties are investigated by DC magnetic-susceptibility
measurements that carried out at low temperatures down to 2 K using a
standard SQUID magnetometer in a magnetic field of 5 Oe on field
cooling. Transport properties addressed to electron mobility, are
extracted from radius of electron localization calculated from
temperature dependence of resistivity. For y = 0, temperature
dependence of dc magnetic-susceptibility (χ) indicated the change of
magnetic behavior from paramagnetic to diamagnetic below 15 K.
Above 15 K, all samples show paramagnetic behavior with the values
of magnetic moment in every volume unit increased with increasing y.
Electron mobility decreased with increasing y.
Abstract: Some plants of genus Schinus have been used in the
folk medicine as topical antiseptic, digestive, purgative, diuretic,
analgesic or antidepressant, and also for respiratory and urinary
infections. Chemical composition of essential oils of S. molle and S.
terebinthifolius had been evaluated and presented high variability
according with the part of the plant studied and with the geographic
and climatic regions. The pharmacological properties, namely
antimicrobial, anti-tumoural and anti-inflammatory activities are
conditioned by chemical composition of essential oils. Taking into
account the difficulty to infer the pharmacological properties of
Schinus essential oils without hard experimental approach, this work
will focus on the development of a decision support system, in terms
of its knowledge representation and reasoning procedures, under a
formal framework based on Logic Programming, complemented with
an approach to computing centered on Artificial Neural Networks
and the respective Degree-of-Confidence that one has on such an
occurrence.
Abstract: Optical biosensors have become a powerful detection
and analysis tool for wide-ranging applications in biomedical research,
pharmaceuticals and environmental monitoring. This study carried out
the computational fluid dynamics (CFD)-based simulations to explore
the dispersion phenomenon in the micro channel of an optical
biosensor. The predicted time sequences of concentration contours
were utilized to better understand the dispersion development occurred
in different geometric shapes of micro channels. The simulation results
showed the surface concentrations at the sensing probe (with the best
performance of a grating coupler) in respect of time to appraise the
dispersion effect and therefore identify the design configurations
resulting in minimum dispersion.
Abstract: Any variation in environmental characteristics of
geomorphosites would lead to destabilisation of their geotouristic
values all around the planet. The Urmia lake, with an area of
approximately 5,500 km2 and a catchment area of 51,876 km2, and to
which various reasons over time, especially in the last fifty years
have seen a sharp decline and have decreased by about 93 % in two
recent decades. These variations are not only driving significant
changes in the morphology and ecology of the present lake
landscape, but at the same time are shaping newly formed
morphologies, which vanished some valuable geomorphosites or
develop into smaller geomorphosites with significant value from a
scientific and cultural point of view. This paper analyses and
discusses features and evolution in several representative coastal and
island geomorphosites. For this purpose, a total of 23 geomorphosites
were studied in two data series (1963 and 2015) and the respective
data were compared and analysed. The results showed, the total loss
in geomorphosites area in a half century amounted to a loss of more
than 90% of the valuable geomorphosites. Moreover, the comparison
between the mean yearly value of coastal area lost over the entire
period and the yearly average calculated for the shorter period (1998-
2014) clearly indicates a pattern of acceleration. This acceleration in
the rate of reduction in lake area was seen in most of the southern
half of the lake. In the region as well, the general water-level falling
is not only causing the loss of a significant water resource, which is
followed by major impact on regional ecosystems, but is also driving
the most marked recent (last century) changes in the geotouristic
landscapes. In fact, the disappearance of geomorphosites means the
loss of tourism phenomenon. In this context attention must be paid to
the question of conservation. The action needed to safeguard
geomorphosites includes: 1) Preventive action, 2) Corrective action,
and 3) Sharing knowledge.
Abstract: Electrodeposition is a simple and economic technique
for precision coating of different shaped substrates with pure metal,
alloy or composite films. Dc electrodeposition was used to produce
Cr, Co-Cr and Co-Cr/TiO2 nano-composite coatings from Cr(III)
based electrolytes onto 316L SS substrates. The effects of TiO2 nanoparticles
concentration on co-deposition of these particles along with
Cr content and microhardness of the coatings were investigated.
Morphology of the Cr, Co-Cr and Co-Cr/TiO2 coatings besides their
tribological behavior were studied. The results showed that increment
of TiO2 nanoparticles concentration from 0 to 30 g L-1 in the bath
increased their co-deposition and Cr content of the coatings from 0 to
3.5 wt.% and from 23.7 to 31.2 wt.%, respectively. Microhardness of
Cr coating was about 920 Hv which was higher than Co-Cr and even
Co-Cr/TiO2 films. Microhardness of Co-Cr and Co-Cr/TiO2 coatings
were improved by increasing their Cr and TiO2 content. All the
coatings had nodular morphology and contained microcracks.
Nodules sizes and the number of microcracks in the alloy and
composite coatings were lower than the Cr film. Wear results
revealed that the Co-Cr/TiO2 coating had the lowest wear loss
between all the samples, while the Cr film had the worst wear
resistance.
Abstract: The fatigue life of tubular joints commonly found in
offshore industry is not only dependent on the value of hot-spot stress
(HSS), but is also significantly influenced by the through-thethickness
stress distribution characterized by the degree of bending
(DoB). The determination of DoB values in a tubular joint is essential
for improving the accuracy of fatigue life estimation using the stresslife
(S–N) method and particularly for predicting the fatigue crack
growth based on the fracture mechanics (FM) approach. In the
present paper, data extracted from finite element (FE) analyses of
tubular KT-joints, verified against experimental data and parametric
equations, was used to investigate the effects of geometrical
parameters on DoB values at the crown 0°, saddle, and crown 180°
positions along the weld toe of central brace in tubular KT-joints
subjected to axial loading. Parametric study was followed by a set of
nonlinear regression analyses to derive DoB parametric formulas for
the fatigue analysis of KT-joints under axial loads. The tubular KTjoint
is a quite common joint type found in steel offshore structures.
However, despite the crucial role of the DoB in evaluating the fatigue
performance of tubular joints, this paper is the first attempt to study
and formulate the DoB values in KT-joints.
Abstract: Water miscible cutting fluids are conventionally used to lubricate and cool the machining zone. But issues related to health hazards, maintenance and disposal costs have limited their usage, leading to application of Minimum Quantity Lubrication (MQL). To increase the effectiveness of MQL, nanocutting fluids are proposed. In the present work, water miscible nanographite cutting fluids of varying concentration are applied at cutting zone by two systems A and B. System A utilizes high pressure air and supplies cutting fluid at a flow rate of 1ml/min. System B uses low pressure air and supplies cutting fluid at a flow rate of 5ml/min. Their performance in machining is evaluated by measuring cutting temperatures, tool wear, cutting forces and surface roughness and compared with dry machining and flood machining. Application of nanocutting fluid using both systems showed better performance than dry machining. Cutting temperatures and cutting forces obtained by both techniques are more than flood machining. But tool wear and surface roughness showed improvement compared to flood machining. Economic analysis has been carried out in all the cases to decide the applicability of the techniques.