Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: Alkali Activated Slag Concrete (AASC) mixes are manufactured by activating ground granulated blast furnace slag (GGBFS) using sodium hydroxide and sodium silicate solutions. The aim of the present experimental research was to investigate the effect of increasing the dosages of sodium oxide (Na2O, in the range of 4 to 8%) and the activator modulus (Ms) (i.e. the SiO2/Na2O ratio, in the range of 0.5 to 1.5) of the alkaline solutions, on the workability and strength characteristics of self-cured (air-cured) alkali activated Indian slag concrete mixes. Further the split tensile and flexure strengths for optimal mixes were studied for each dosage of Na2O.It is observed that increase in Na2O concentration increases the compressive, split-tensile and flexural strengths, both at the early and later-ages, while increase in Ms, decreases the workability of the mixes. An optimal Ms of 1.25 is found at various Na2O dosages. No significant differences in the strength performances were observed between AASCs manufactured with alkali solutions prepared using either of potable and de-ionized water.
Abstract: Optimum communication and performance in
Wireless Sensor Networks, constitute multi-facet challenges due to
the specific networking characteristics as well as the scarce resource
availability. Furthermore, it is becoming increasingly apparent that
isolated layer based approaches often do not meet the demands posed
by WSNs applications due to omission of critical inter-layer
interactions and dependencies. As a counterpart, cross-layer is
receiving high interest aiming to exploit these interactions and
increase network performance. However, in order to clearly identify
existing dependencies, comprehensive performance studies are
required evaluating the effect of different critical network parameters
on system level performance and behavior.This paper-s main
objective is to address the need for multi-parametric performance
evaluations considering critical network parameters using a well
known network simulator, offering useful and practical conclusions
and guidelines. The results reveal strong dependencies among
considered parameters which can be utilized by and drive future
research efforts, towards designing and implementing highly efficient
protocols and architectures.
Abstract: Artificial Immune System (AIS) is relatively naive paradigm for intelligent computations. The inspiration for AIS is derived from natural Immune System (IS). Classically it is believed that IS strives to discriminate between self and non-self. Most of the existing AIS research is based on this approach. Danger Theory (DT) argues this approach and proposes that IS fights against danger producing elements and tolerates others. We, the computational researchers, are not concerned with the arguments among immunologists but try to extract from it novel abstractions for intelligent computation. This paper aims to follow DT inspiration for intelligent data processing. The approach may introduce new avenue in intelligent processing. The data used is system calls data that is potentially significant in intrusion detection applications.
Abstract: XML is a markup language which is becoming the
standard format for information representation and data exchange. A
major purpose of XML is the explicit representation of the logical
structure of a document. Much research has been performed to
exploit logical structure of documents in information retrieval in
order to precisely extract user information need from large
collections of XML documents. In this paper, we describe an XML
information retrieval weighting scheme that tries to find the most
relevant elements in XML documents in response to a user query.
We present this weighting model for information retrieval systems
that utilize plausible inferences to infer the relevance of elements in
XML documents. We also add to this model the Dempster-Shafer
theory of evidence to express the uncertainty in plausible inferences
and Dempster-Shafer rule of combination to combine evidences
derived from different inferences.
Abstract: People usually have a telephone voice, which means
they adjust their speech to fit particular situations and to blend in with
other interlocutors. The question is: Do we speak differently to
different people? This possibility has been suggested by social
psychologists within Accommodation Theory [1]. Converging toward
the speech of another person can be regarded as a polite speech
strategy while choosing a language not used by the other interlocutor
can be considered as the clearest example of speech divergence [2].
The present study sets out to investigate such processes in the course
of everyday telephone conversations. Using Joos-s [3] model of
formality in spoken English, the researchers try to explore
convergence to or divergence from the addressee. The results
propound the actuality that lexical choice, and subsequently, patterns
of style vary intriguingly in concordance with the person being
addressed.
Abstract: In this research, Forming Limit Diagrams for supertension
sheet metals which are using in automobile industry have
been obtained. The exerted strains to sheet metals have been
measured with four different methods and the errors of each method
have also been represented. These methods have been compared with
together and the most efficient and economic way of extracting of the
exerted strains to sheet metals has been introduced. In this paper total
error and uncertainty of FLD extraction procedures have been
derived. Determination of the measurement uncertainty in extracting
of FLD has a great importance in design and analysis of the sheet
metal forming process.
Abstract: The efficient knowledge management system (KMS)
is one of the important strategies to help firms to achieve sustainable
competitive advantages, but little research has been conducted to
understand what contributes to the KMS success. This study thus set
to investigate the determinants of KMS success in the context of Thai
banking industry. A questionnaire survey was conducted in four
major Thai Banks to test the proposed KMS Success model.
The result of this study shows that KMS use and user satisfaction
relate significantly to the success of KMS, and knowledge quality,
service quality and trust lead to system use, and knowledge quality,
system quality and trust lead to user satisfaction. However, this
research focuses only on system and user-related factors. Future
research thus can extend to study factors such as management support
and organization readiness.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: Scale defects are common surface defects in hot steel rolling. The modelling of such defects is problematic and their causes are not straightforward. In this study, we investigated genetic algorithms in search for a mathematical solution to scale formation. For this research, a high-dimensional data set from hot steel rolling process was gathered. The synchronisation of the variables as well as the allocation of the measurements made on the steel strip were solved before the modelling phase.
Abstract: It has been shown that in most accidents the driver is responsible due to being distracted or misjudging the situation. In order to solve such problems research has been dedicated to developing driver assistance systems that are able to monitor the traffic situation around the vehicle. This paper presents methods for recognizing several circumstances on a road. The methods use both the in-vehicle warning systems and the roadside infrastructure. Preliminary evaluation results for fog and ice-on-road detection are presented. The ice detection results are based on data recorded in a test track dedicated to tyre friction testing. The achieved results anticipate that ice detection could work at a performance of 70% detection with the right setup, which is a good foundation for implementation. However, the full benefit of the presented cooperative system is achieved by fusing the outputs of multiple data sources, which is the key point of discussion behind this publication.
Abstract: To investigate the behavior of sheet metals during
forming tailor welded blanks (TWB) of various thickness made via
Co2 Laser welding are under consideration. These blanks are formed
used two different forming methods of rubber as well as the
conventional punch and die methods. The main research objective is
the effects of using a rubber die instead of a solid one the
displacement of the weld line and the press force needed for forming.
Specimens with thicknesses of 0.5, 0.6, 0.8 and 1mm are subjected to
Erichsen two dimensional tests and the resulted force for each case
are compared. This is followed by a theoretical and numerical study
of press force and weld line displacement. It is concluded that using
rubber pad forming (RPF) causes a reduction in weld line
displacement and an increase in the press force.
Abstract: Company mergers and acquisitions reached their peak
in the twenty-first century. Mergers and acquisitions have become one
of the competitive strategies for external growth. In general, it is
believed that mergers and acquisitions can create synergies. However,
they require complete information technology system and service
integration, especially in the banking industry. Much of the research
has focused on performance evaluation, shareholder equity allocation,
or even the increase of company market value after the merger and
acquisition, whereas few scholars have focused on information system
integration post merger and acquisition. This study indicates the role
of information systems after a merger and acquisition, explaining the
benefits of information system integration using a merger and
acquisition case in the banking industry as an example. In addition, we
discuss factors that affect the performance of information system
integration, and utilize system dynamics to interpret the relationship
among factors that affect information system integration performance
in the banking industry after a merger and acquisition.
Abstract: carrot is one of the important root vegetable crops,
and it is highly nutritious as it contains appreciable amount of
vitamins, minerals and β-carotene. The major objective of current
research was to evaluate the chemical composition of carrot variety
'Nante' hybrids in general and to select the best samples for fresh-cut
salad production. The research was accomplished on fresh in Latvia
cultivated carrots harvested in Zemgale region in the first part of
October, 2011 and immediately used for experiments. Late-bearing
variety 'Nante' hybrid carrots were used for analysis:
'Nante/Berlikum', 'Nante/Maestro', 'Nante/Forto', 'Nante/Bolero'
and 'Nante/Champion'. The quality parameters as moisture, soluble
solid, firmness, b-carotene, carotenoid, color, polyphenols, total
phenolic compounds and total antioxidant capacity were analyzed
using standard methods. For fresh-cut salad production as more
applicable could be recommended hybrids 'Nante/Forto' and
'Nante/Berlikum' - mainly because it-s higher nutritive value, as
higher total phenolic compounds, polyphenols and pronounced
antioxidant capacity.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: This research aims to study value-creation process of
producing monk-s bowls, Thai traditional handicrafts, which is facing problems in adapting to the changing society. It also aims to identify
problems and obstacles to value creation. This research is based on a case study of monk-s bowl manufactures from Ban-Baat Village,
Bangkok. The conceptual framework is based on the model of value
chain to analyze the process.
The research methodology is qualitative. This research found that the value-creation process of monk-s bowls consists of eight
activities contributing to adding value to the products and increasing
profits to the producers in return. Five major problems and obstacles
are found.
The research suggests that these problems and obstacles limit the manufacturers- potential for creating more valued product and lead to business stagnation. These problems should be addressed and solved with collaboration among the government, the private sector and the
manufacturers.
Abstract: Methods of contemporary mathematical physics such
as chaos theory are useful for analyzing and understanding the
behavior of complex biological and physiological systems. The three
dimensional model of HIV/AIDS is the basis of active research since
it provides a complete characterization of disease dynamics and the
interaction of HIV-1 with the immune system. In this work, the
behavior of the HIV system is analyzed using the three dimensional
HIV model and a chaotic measure known as the Hurst exponent.
Results demonstrate that Hurst exponents of CD4, CD8 cells and
viral load vary nonlinearly with respect to variations in system
parameters. Further, it was observed that the three dimensional HIV
model can accommodate both persistent (H>0.5) and anti-persistent
(H
Abstract: Control of commutation of switched reluctance (SR)
motor has been an area of interest for researchers for sometime now
with mixed successes in addressing the inherent challenges. New
technologies, processing schemes and methods have been adopted to
make sensorless SR drive a reality. There are a number of
conceptual, offline, analytical and online solutions in literature that
have varying complexities and achieved equally varying degree of
robustness and accuracies depending on the method used to address
the challenges and the SR drive application. Magnetic coupling is
one such challenge when using active probing techniques to
determine rotor position of a SR motor from stator winding. This
paper studies the effect of back-of-core saturation on the detected
rotor position and presents results on measurement made on a 4-
phase SR motor. The results shows that even for a four phase motor
which is excited one phase at a time and using the electrically
opposite phase for active position probing, the back-of-core
saturation effects should not be ignored.
Abstract: Association rules are an important problem in data
mining. Massively increasing volume of data in real life databases
has motivated researchers to design novel and incremental algorithms
for association rules mining. In this paper, we propose an incremental
association rules mining algorithm that integrates shocking
interestingness criterion during the process of building the model. A
new interesting measure called shocking measure is introduced. One
of the main features of the proposed approach is to capture the user
background knowledge, which is monotonically augmented. The
incremental model that reflects the changing data and the user beliefs
is attractive in order to make the over all KDD process more
effective and efficient. We implemented the proposed approach and
experiment it with some public datasets and found the results quite
promising.