Abstract: Dynamics of a rotor supported by air bearings is
strongly depends on the pressure distribution between the rotor and
the bearing. In this study, internal pressure in air bearings is
numerical and experimental analyzed for different radial clearances.
Firstly the pressure distribution between rotor and bearing is modeled
using Reynold's equation and this model is solved numerically. The
rotor-bearing system is also modeled in four degree of freedom and it
is simulated for different radial clearances. Then, in order to validate
numerical results, a test rig is designed and the rotor bearing system
is run under the same operational conditions. Pressure signals of left
and right bearings are recorded. Internal pressure variations are
compared for numerical and experimental results for different radial
clearances.
Abstract: Machining of hard materials is a recent technology for
direct production of work-pieces. The primary challenge in
machining these materials is selection of cutting tool inserts which
facilitates an extended tool life and high-precision machining of the
component. These materials are widely for making precision parts for
the aerospace industry. Nickel-based alloys are typically used in
extreme environment applications where a combination of strength,
corrosion resistance and oxidation resistance material characteristics
are required. The present paper reports the theoretical and
experimental investigations carried out to understand the influence of
machining parameters on the response parameters. Considering the
basic machining parameters (speed, feed and depth of cut) a study has
been conducted to observe their influence on material removal rate,
surface roughness, cutting forces and corresponding tool wear.
Experiments are designed and conducted with the help of Central
Composite Rotatable Design technique. The results reveals that for a
given range of process parameters, material removal rate is favorable
for higher depths of cut and low feed rate for cutting forces. Low feed
rates and high values of rotational speeds are suitable for better finish
and higher tool life.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: This paper deals with current strategic challenges
related to the reshaping of the basic conditions of corporate operations.
Through the experimental analysis of some domestic corporations, it
presents how and to what extent Hungarian corporations are prepared
for the current strategic challenges. The study examines how strategic
directions and answer opportunities have changed in the following
interrelated areas in the past five years: economic globalization,
corporate sustainability, IT applications, labor force diversity and
ethical competences. The conclusions of the empirical survey give a
reliable basis on which economic organizations and enterprises can
formulate their strategy.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: Powder metallurgy (P/M) is the only economic way to
produce porous parts/products. P/M can produce near net shape parts
hence reduces wastage of raw material and energy, avoids various
machining operations. The most vital use of P/M is in production of
metallic filters and self lubricating bush bearings and siding surfaces.
The porosity of the part can be controlled by varying compaction
pressure, sintering temperature and composition of metal powder
mix. The present work is aimed for experimental analysis of friction
and wear properties of self lubricating copper and tin bush bearing.
Experimental results confirm that wear rate of sintered component
is lesser for components having 10% tin by weight percentage. Wear
rate increases for high tin percentage (experimented for 20% tin and
30% tin) at same sintering temperature. Experimental results also
confirms that wear rate of sintered component is also dependent on
sintering temperature, soaking period, composition of the preform,
compacting pressure, powder particle shape and size.
Interfacial friction between die and punch, between inter powder
particles, between die face and powder particle depends on
compaction pressure, powder particle size and shape, size and shape
of component which decides size & shape of die & punch, material of
die & punch and material of powder particles.
Abstract: This work presents the result of investigations aimed
at determining the hardness of the welded Chromoly (A 4130) steel
plate of 2” thickness. Multi pass welding for the thick sections was
carried out and analyzed for the Chromoly alloy steel plates. The
study of hardness at the weld metal reveals that there is the presence
of different micro structure products which yields diverse properties.
The welding carried out using GMAW with ER70s-2 electrode.
Single V groove design was selected for the butt joint configuration.
The presence of hydrogen has been suppressed by selecting low
hydrogen electrode. Preheating of the plate prior to welding reduces
the cooling rate which also affects the weld metal microstructure. The
shielding gas composition used in this analysis is 80% Ar-20% CO2.
The experimental analysis gives the detailed study of the hardness of
the material.
Abstract: The paper deals with current issues in research of
advanced methods to increase reliability of traditional timber
structural elements. It analyses the issue of strengthening of bent
timber beams, such as ceiling beams in old (historical) buildings with
additional concrete slab in combination with externally bonded fibre -
reinforced polymer. The paper describes experimental testing of
composite timber-concrete beam with FRP reinforcement and
compares results with FEM analysis.
Abstract: When insulation and rehabilitation of structures is important to use quality building materials with high utility value. One potentially interesting and promising groups of construction materials in this area are advanced, thermally insulating plaster silicate based. With the present trend reduction of energy consumption of building structures and reducing CO2 emissions to be developed capillary-active materials that are characterized by their low density, low thermal conductivity while maintaining good mechanical properties.
The paper describes the results of research activities aimed at the development of thermal insulating and rehabilitation material ongoing at the Technical University in Brno, Faculty of Civil Engineering. The achieved results of this development will be the basis for subsequent experimental analysis of the influence of thermal and moisture loads developed on these materials.
Abstract: The demand for efficient transonic transport has been growing every day and may turn out to be the most pressed innovation in coming years. Oblique wing configuration was proposed as an alternative to conventional wing configuration for supersonic and transonic passenger aircraft due to its aerodynamic advantages. This paper re-demonstrates the aerodynamic advantages of oblique wing configuration using open source CFD code. The aerodynamic data were generated using Panel Method. Results show that Oblique Wing concept with elliptical wing planform offers a significant reduction in drag at transonic and supersonic speeds and approximately twice the lift distribution compared to conventional operating aircrafts. The paper also presents a preliminary conceptual aircraft sizing which can be used for further experimental analysis.
Abstract: Dynamic tests are an important step of the design of engineering structures, because the accuracy of predictions of theoretical–numerical procedures can be assessed. In experimental test of moving loads that is one of the major research topics, the load is modeled as a simple moving mass or a small vehicle. This paper deals with the applicability of Non-contact Moving Load (NML) for vibration analysis. For this purpose, an experimental set-up is designed to generate the different types of NML including constant and harmonic. The proposed method relies on pressurized air which is useful, especially when dealing with fragile or sensitive structures. To demonstrate the performance of this system, the set-up is employedfor a modal analysis of a beam and detecting crack of the beam.The obtained results indicate that the experimental set-up for NML can be an attractive alternative to the moving load problems.
Abstract: The goal of a network-based intrusion detection
system is to classify activities of network traffics into two major
categories: normal and attack (intrusive) activities. Nowadays, data
mining and machine learning plays an important role in many
sciences; including intrusion detection system (IDS) using both
supervised and unsupervised techniques. However, one of the
essential steps of data mining is feature selection that helps in
improving the efficiency, performance and prediction rate of
proposed approach. This paper applies unsupervised K-means
clustering algorithm with information gain (IG) for feature selection
and reduction to build a network intrusion detection system. For our
experimental analysis, we have used the new NSL-KDD dataset,
which is a modified dataset for KDDCup 1999 intrusion detection
benchmark dataset. With a split of 60.0% for the training set and the
remainder for the testing set, a 2 class classifications have been
implemented (Normal, Attack). Weka framework which is a java
based open source software consists of a collection of machine
learning algorithms for data mining tasks has been used in the testing
process. The experimental results show that the proposed approach is
very accurate with low false positive rate and high true positive rate
and it takes less learning time in comparison with using the full
features of the dataset with the same algorithm.
Abstract: Safe drinking water is one of the biggest issues facing
the planet this century. The primary aim of this paper is to present our
research focused on theoretical and experimental analysis of potable
water and in-building water distribution systems from the point of
view of microbiological risk on the basis of confrontation between
the theoretical analysis and synthesis of gathered information in
conditions of the Slovak Republic. The presence of the bacteria
Legionella in water systems, especially in hot water distribution
system, represents in terms of health protection of inhabitants the
crucial problem which cannot be overlooked. Legionella
pneumophila discovery, its classification and its influence on
installations inside buildings are relatively new. There are a lot of
guidelines and regulations developed in many individual countries for
the design, operation and maintenance for tap water systems to avoid
the growth of bacteria Legionella pneumophila, but in Slovakia we
don-t have any. The goal of this paper is to show the necessity of
prevention and regulations for installations inside buildings verified
by simulation methods.
Abstract: Bloom filter is a probabilistic and memory efficient
data structure designed to answer rapidly whether an element is
present in a set. It tells that the element is definitely not in the set but
its presence is with certain probability. The trade-off to use Bloom
filter is a certain configurable risk of false positives. The odds of a
false positive can be made very low if the number of hash function is
sufficiently large. For spam detection, weight is attached to each set
of elements. The spam weight for a word is a measure used to rate the
e-mail. Each word is assigned to a Bloom filter based on its weight.
The proposed work introduces an enhanced concept in Bloom filter
called Bin Bloom Filter (BBF). The performance of BBF over
conventional Bloom filter is evaluated under various optimization
techniques. Real time data set and synthetic data sets are used for
experimental analysis and the results are demonstrated for bin sizes 4,
5, 6 and 7. Finally analyzing the results, it is found that the BBF
which uses heuristic techniques performs better than the traditional
Bloom filter in spam detection.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: This paper presents an architecture to assist in the
development of tools to perform experimental analysis. Existing
implementations of tools based on this architecture are also described
in this paper. These tools are applied to the real world problem of
fault attack emulation and detection in cryptographic algorithms.
Abstract: The survival of publicly listed companies largely
depends on their stocks being liquidly traded. This goal can be
achieved when new investors are attracted to invest on companies-
stocks. Among different groups of investors, individual investors are
generally less able to objectively evaluate companies- risks and
returns, and tend to be emotionally biased in their investing
decisions. Therefore their decisions may be formed as a result of
perceived risks and returns, and influenced by companies- images.
This study finds that perceived risk, perceived returns and trust
directly affect individual investors- trading decisions while attitude
towards brand partially mediates the relationships. This finding
suggests that, in courting individual investors, companies still need to
perform financially while building a good image can result in their
stocks being accepted quicker than the stocks of good performing
companies with hidden images.
Abstract: Wave generation methodology has been developed
and validated by simulating wave in CFD. In this analysis, Flap type
wave maker has been modeled numerically with wave basin to
generate waves for marine experimental analysis. Irregular waves are
arrived from the wave spectrum, and this wave has been simulated in
CFD. Generated irregular wave has been compared with an analytical
wave. Simulated wave has been processed for FFT analysis, and the
wave spectrum is validated with original wave spectrum.
Abstract: Conventional approaches in the implementation of logic programming applications on embedded systems are solely of software nature. As a consequence, a compiler is needed that transforms the initial declarative logic program to its equivalent procedural one, to be programmed to the microprocessor. This approach increases the complexity of the final implementation and reduces the overall system's performance. On the contrary, presenting hardware implementations which are only capable of supporting logic programs prevents their use in applications where logic programs need to be intertwined with traditional procedural ones, for a specific application. We exploit HW/SW codesign methods to present a microprocessor, capable of supporting hybrid applications using both programming approaches. We take advantage of the close relationship between attribute grammar (AG) evaluation and knowledge engineering methods to present a programmable hardware parser that performs logic derivations and combine it with an extension of a conventional RISC microprocessor that performs the unification process to report the success or failure of those derivations. The extended RISC microprocessor is still capable of executing conventional procedural programs, thus hybrid applications can be implemented. The presented implementation is programmable, supports the execution of hybrid applications, increases the performance of logic derivations (experimental analysis yields an approximate 1000% increase in performance) and reduces the complexity of the final implemented code. The proposed hardware design is supported by a proposed extended C-language called C-AG.