Abstract: This paper is about hiding RFID tag identifier (ID)
using handheld device like a cellular phone. By modifying the tag ID
of objects periodically or manually using cellular phone built-in a
RFID reader chip or with a external RFID reader device, we can
prevent other people from gathering the information related with
objects querying information server (like an EPC IS) with a tag ID or
deriving the information from tag ID-s code structure or tracking the
location of the objects and the owner of the objects. In this paper, we
use a cryptographic algorithm for modification and restoring of RFID
tag ID, and for one original tag ID, there are several different
temporary tag ID, periodically.
Abstract: In this paper the performance of unified power flow
controller is investigated in controlling the flow of po wer over the
transmission line. Voltage sources model is utilized to study the
behaviour of the UPFC in regulating the active, reactive power and
voltage profile. This model is incorporated in Newton Raphson
algorithm for load flow studies. Simultaneous method is employed
in which equations of UPFC and the power balance equations of
network are combined in to one set of non-linear algebraic equations.
It is solved according to the Newton raphson algorithm. Case studies
are carried on standard 5 bus network. Simulation is done in Matlab.
The result of network with and without using UPFC are compared in
terms of active and reactive power flows in the line and active and
reactive power flows at the bus to analyze the performance of UPFC.
Abstract: This paper presents a novel CMOS four-transistor
SRAM cell for very high density and low power embedded SRAM
applications as well as for stand-alone SRAM applications. This cell
retains its data with leakage current and positive feedback without
refresh cycle. The new cell size is 20% smaller than a conventional
six-transistor cell using same design rules. Also proposed cell uses
two word-lines and one pair bit-line. Read operation perform from
one side of cell, and write operation perform from another side of
cell, and swing voltage reduced on word-lines thus dynamic power
during read/write operation reduced. The fabrication process is fully
compatible with high-performance CMOS logic technologies,
because there is no need to integrate a poly-Si resistor or a TFT load.
HSPICE simulation in standard 0.25μm CMOS technology confirms
all results obtained from this paper.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: Optimal load shedding (LS) design as an emergency plan is one of the main control challenges posed by emerging new uncertainties and numerous distributed generators including renewable energy sources in a modern power system. This paper presents an overview of the key issues and new challenges on optimal LS synthesis concerning the integration of wind turbine units into the power systems. Following a brief survey on the existing LS methods, the impact of power fluctuation produced by wind powers on system frequency and voltage performance is presented. The most LS schemas proposed so far used voltage or frequency parameter via under-frequency or under-voltage LS schemes. Here, the necessity of considering both voltage and frequency indices to achieve a more effective and comprehensive LS strategy is emphasized. Then it is clarified that this problem will be more dominated in the presence of wind turbines.
Abstract: A new deployment of the multiple criteria decision
making (MCDM) techniques: the Simple Additive Weighting
(SAW), and the Technique for Order Preference by Similarity to
Ideal Solution (TOPSIS) for portfolio allocation, is demonstrated in
this paper. Rather than exclusive reference to mean and variance as in
the traditional mean-variance method, the criteria used in this
demonstration are the first four moments of the portfolio distribution.
Each asset is evaluated based on its marginal impacts to portfolio
higher moments that are characterized by trapezoidal fuzzy numbers.
Then centroid-based defuzzification is applied to convert fuzzy
numbers to the crisp numbers by which SAW and TOPSIS can be
deployed. Experimental results suggest the similar efficiency of these
MCDM approaches to selecting dominant assets for an optimal
portfolio under higher moments. The proposed approaches allow
investors flexibly adjust their risk preferences regarding higher
moments via different schemes adapting to various (from
conservative to risky) kinds of investors. The other significant
advantage is that, compared to the mean-variance analysis, the
portfolio weights obtained by SAW and TOPSIS are consistently
well-diversified.
Abstract: In this paper, we give the generalized alternating twostage method in which the inner iterations are accomplished by a generalized alternating method. And we present convergence results of the method for solving nonsingular linear systems when the coefficient matrix of the linear system is a monotone matrix or an H-matrix.
Abstract: This research was conducted in the Pua Watershed whereas located in the Upper Nan River Basin in Nan province, Thailand. Nan River basin originated in Nan province that comprises of many tributary streams to produce as inflow to the Sirikit dam provided huge reservoir with the storage capacity of 9510 million cubic meters. The common problems of most watersheds were found i.e. shortage water supply for consumption and agriculture utilizations, deteriorate of water quality, flood and landslide including debris flow, and unstable of riverbank. The Pua Watershed is one of several small river basins that flow through the Nan River Basin. The watershed includes 404 km2 representing the Pua District, the Upper Nan Basin, or the whole Nan River Basin, of 61.5%, 18.2% or 1.2% respectively. The Pua River is a main stream producing all year streamflow supplying the Pua District and an inflow to the Upper Nan Basin. Its length approximately 56.3 kilometers with an average slope of the channel by 1.9% measured. A diversion weir namely Pua weir bound the plain and mountainous areas with a very steep slope of the riverbed to 2.9% and drainage area of 149 km2 as upstream watershed while a mild slope of the riverbed to 0.2% found in a river reach of 20.3 km downstream of this weir, which considered as a gauged basin. However, the major branch streams of the Pua River are ungauged catchments namely: Nam Kwang and Nam Koon with the drainage area of 86 and 35 km2 respectively. These upstream watersheds produce runoff through the 3-streams downstream of Pua weir, Jao weir, and Kang weir, with an averaged annual runoff of 578 million cubic meters. They were analyzed using both statistical data at Pua weir and simulated data resulted from the hydrologic modeling system (HEC–HMS) which applied for the remaining ungauged basins. Since the Kwang and Koon catchments were limited with lack of hydrological data included streamflow and rainfall. Therefore, the mathematical modeling: HEC-HMS with the Snyder-s hydrograph synthesized and transposed methods were applied for those areas using calibrated hydrological parameters from the upstream of Pua weir with continuously daily recorded of streamflow and rainfall data during 2008-2011. The results showed that the simulated daily streamflow and sum up as annual runoff in 2008, 2010, and 2011 were fitted with observed annual runoff at Pua weir using the simple linear regression with the satisfied correlation R2 of 0.64, 062, and 0.59, respectively. The sensitivity of simulation results were come from difficulty using calibrated parameters i.e. lag-time, coefficient of peak flow, initial losses, uniform loss rates, and missing some daily observed data. These calibrated parameters were used to apply for the other 2-ungauged catchments and downstream catchments simulated.
Abstract: The self-organizing map (SOM) model is a well-known neural network model with wide spread of applications. The main characteristics of SOM are two-fold, namely dimension reduction and topology preservation. Using SOM, a high-dimensional data space will be mapped to some low-dimensional space. Meanwhile, the topological relations among data will be preserved. With such characteristics, the SOM was usually applied on data clustering and visualization tasks. However, the SOM has main disadvantage of the need to know the number and structure of neurons prior to training, which are difficult to be determined. Several schemes have been proposed to tackle such deficiency. Examples are growing/expandable SOM, hierarchical SOM, and growing hierarchical SOM. These schemes could dynamically expand the map, even generate hierarchical maps, during training. Encouraging results were reported. Basically, these schemes adapt the size and structure of the map according to the distribution of training data. That is, they are data-driven or dataoriented SOM schemes. In this work, a topic-oriented SOM scheme which is suitable for document clustering and organization will be developed. The proposed SOM will automatically adapt the number as well as the structure of the map according to identified topics. Unlike other data-oriented SOMs, our approach expands the map and generates the hierarchies both according to the topics and their characteristics of the neurons. The preliminary experiments give promising result and demonstrate the plausibility of the method.
Abstract: A way of achieving nanodimentional structural elements in high carbon steel by special kind of heat treatment and cold plastic deformation is being explored. This leads to increasing interlamellar spacing of ferrite-carbide mixture. Decreasing the interlamellar spacing with cooling temperature increasing is determined. Experiments confirm such interlamellar spacing with which high carbon steel demonstrates the highest treatment and hardening capability. Total deformation degree effect on interlamellar spacing value in a ferrite-carbide mixture is obtained. Mechanical experiments results show that high carbon steel after heat treatment and repetitive cold plastic deformation possesses high tensile strength and yield strength keeping good percentage elongation.
Abstract: The steady-state operation of maintaining voltage
stability is done by switching various controllers scattered all over
the power network. When a contingency occurs, whether forced or
unforced, the dispatcher is to alleviate the problem in a minimum
time, cost, and effort. Persistent problem may lead to blackout. The
dispatcher is to have the appropriate switching of controllers in terms
of type, location, and size to remove the contingency and maintain
voltage stability. Wrong switching may worsen the problem and that
may lead to blackout. This work proposed and used a Fuzzy CMeans
Clustering (FCMC) to assist the dispatcher in the decision
making. The FCMC is used in the static voltage stability to map
instantaneously a contingency to a set of controllers where the types,
locations, and amount of switching are induced.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.
Abstract: In North America, Most power distribution systems
employ a four-wire multi-grounded neutral (MGN) design. This paper has explained the inherent characteristics of multi-grounded three-phase four-wire distribution systems under unbalanced
situations. As a result, the mechanism of voltage swell and voltage sag in MGN feeders becomes difficult to understand. The simulation
tool that has been used in this paper is MATLAB under Windows software. In this paper the equivalent model of a full-scale multigrounded
distribution system implemented by MATLAB is
introduced. The results are expected to help utility engineers to understand the impact of MGN on distribution system operations.
Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: Model Predictive Control (MPC) is increasingly being
proposed for real time applications and embedded systems. However
comparing to PID controller, the implementation of the MPC in
miniaturized devices like Field Programmable Gate Arrays (FPGA)
and microcontrollers has historically been very small scale due to its
complexity in implementation and its computation time requirement.
At the same time, such embedded technologies have become an
enabler for future manufacturing enterprises as well as a transformer
of organizations and markets. Recently, advances in microelectronics
and software allow such technique to be implemented in embedded
systems. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and
applied control technique in the industrial engineering. In fact in
this paper, we propose an efficient framework for implementation
of Generalized Predictive Control (GPC) in the performed STM32
microcontroller. The STM32 keil starter kit based on a JTAG interface
and the STM32 board was used to implement the proposed GPC
firmware. Besides the GPC, the PID anti windup algorithm was
also implemented using Keil development tools designed for ARM
processor-based microcontroller devices and working with C/Cµ
langage. A performances comparison study was done between both
firmwares. This performances study show good execution speed and
low computational burden. These results encourage to develop simple
predictive algorithms to be programmed in industrial standard hardware.
The main features of the proposed framework are illustrated
through two examples and compared with the anti windup PID
controller.
Abstract: The application of a simple microcontroller to deal
with a three variable input and a single output fuzzy logic controller,
with Proportional – Integral – Derivative (PID) response control
built-in has been tested for an automatic voltage regulator. The
fuzzifiers are based on fixed range of the variables of output voltage.
The control output is used to control the wiper motor of the auto
transformer to adjust the voltage, using fuzzy logic principles, so that
the voltage is stabilized. In this report, the author will demonstrate
how fuzzy logic might provide elegant and efficient solutions in the
design of multivariable control based on experimental results rather
than on mathematical models.
Abstract: In this paper, we propose a fully-utilized, block-based 2D DWT (discrete wavelet transform) architecture, which consists of four 1D DWT filters with two-channel QMF lattice structure. The proposed architecture requires about 2MN-3N registers to save the intermediate results for higher level decomposition, where M and N stand for the filter length and the row width of the image respectively. Furthermore, the proposed 2D DWT processes in horizontal and vertical directions simultaneously without an idle period, so that it computes the DWT for an N×N image in a period of N2(1-2-2J)/3. Compared to the existing approaches, the proposed architecture shows 100% of hardware utilization and high throughput rates. To mitigate the long critical path delay due to the cascaded lattices, we can apply the pipeline technique with four stages, while retaining 100% of hardware utilization. The proposed architecture can be applied in real-time video signal processing.
Abstract: The development of entrepreneurial competences of
farmers has been pointed out as a necessary condition for the
modernization of land in facing the phenomenon of globalization.
However, the educational processes involved in such a development
have been studied little, especially in emerging economies. This
research aims to enlighten some of the critical issues behind the early
stages of the transformation of farmers into entrepreneurs, through in
depth interviews with farmers, entrepreneurial promoters and public
officials participating in a public pilot project in Mexico. Although
major impacts were expected only in the long run, important positive
changes in the mind set of farmers and other participants were found
in early stages of the intervention. Apparently, the farmers started a
process of becoming more conscious about the importance of
preserving the aquiferous resources, as well as more market and
entrepreneurial oriented.
Abstract: The condition of lightning surge causes the traveling waves and the temporary increase in voltage in the transmission line system. Lightning is the most harmful for destroying the transmission line and setting devices so it is necessary to study and analyze the temporary increase in voltage for designing and setting the surge arrester. This analysis describes the figure of the lightning wave in transmission line with 115 kV voltage level in Thailand by using ATP/EMTP program to create the model of the transmission line and lightning surge. Because of the limit of this program, it must be calculated for the geometry of the transmission line and surge parameter and calculation in the manual book for the closest value of the parameter. On the other hand, for the effects on surge protector when the lightning comes, the surge arrester model must be right and standardized as metropolitan electrical authority's standard. The candidate compared the real information to the result from calculation, also. The results of the analysis show that the temporary increase in voltage value will be rise to 326.59 kV at the line which is done by lightning when the surge arrester is not set in the system. On the other hand, the temporary increase in voltage value will be 182.83 kV at the line which is done by lightning when the surge arrester is set in the system and the period of the traveling wave is reduced, also. The distance for setting the surge arrester must be as near to the transformer as possible. Moreover, it is necessary to know the right distance for setting the surge arrester and the size of the surge arrester for preventing the temporary increase in voltage, effectively.
Abstract: An envelope echo signal measurement is proposed in
this paper using echo signal observation from the 200 kHz echo
sounder receiver. The envelope signal without any object is compared
with the envelope signal of the sphere. Two diameter size steel ball
(3.1 cm & 2.2 cm) and two diameter size air filled stainless steel ball
(4.8 cm & 7.4 cm) used in this experiment. The target was positioned
about 0.5 m and 1.0 meter from the transducer face using nylon rope.
From the echo observation in time domain, it is obviously shown that
echo signal structure is different between the size, distance and type
of metal sphere. The amplitude envelope voltage for the bigger
sphere is higher compare to the small sphere and it confirm that the
bigger sphere have higher target strength compare to the small
sphere. Although the structure signal without any object are different
compare to the signal from the sphere, the reflected signal from the
tank floor increase linearly with the sphere size. We considered this
event happened because of the object position approximately to the
tank floor.