Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.
Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: Three purified diets were formulated using fish meal,
soya bean, wheat flour, palm oil, minerals and maltose. The
carbohydrate in the diets was increased from 5 to 15% by changing
the cellulose content to study the effect of dietary carbohydrate level
on the growth parameters of Nile tilapia Oreochromis niloticus. The
protein and the lipid contents were kept constant in all the diets. The
results showed that, weight gain, protein efficiency ratio, net protein
utilisation and hepatosomatic index of fish fed the diet containing
15% cellulose were the lowest among all groups. Addition, the fish
fed the diet containing 5% cellulose had the best specific growth rate,
and food conversion ratio. While, there was no effect of the dietary
cellulose levels on condition factor and survival rate. These results
indicate that Nile tilapia fingerlings are able to utilize dietary
cellulose does not exceed 10% in their feed for optimum growth.
Abstract: Chatter vibrations and process instabilities are the
most important factors limiting the productivity of the milling
process. Chatter can leads to damage of the tool, the part or the
machine tool. Therefore, the estimation and prediction of the process
stability is very important. The process stability depends on the
spindle speed, the depth of cut and the width of cut. In milling, the
process conditions are defined in the NC-program. While the spindle
speed is directly coded in the NC-program, the depth and width of cut
are unknown. This paper presents a new simulation based approach
for the prediction of the depth and width of cut of a milling process.
The prediction is based on a material removal simulation with an
analytically represented tool shape and a multi-dexel approach for the
workpiece. The new calculation method allows the direct estimation
of the depth and width of cut, which are the influencing parameters of
the process stability, instead of the removed volume as existing
approaches do. The knowledge can be used to predict the stability of
new, unknown parts. Moreover with an additional vibration sensor,
the stability lobe diagram of a milling process can be estimated and
improved based on the estimated depth and width of cut.
Abstract: Evolution strategy (ES) is a well-known instance of evolutionary algorithms, and there have been many studies on ES. In this paper, the author proposes an extended ES for solving fuzzy-valued optimization problems. In the proposed ES, genotype values are not real numbers but fuzzy numbers. Evolutionary processes in the ES are extended so that it can handle genotype instances with fuzzy numbers. In this study, the proposed method is experimentally applied to the evolution of neural networks with fuzzy weights and biases. Results reveal that fuzzy neural networks evolved using the proposed ES with fuzzy genotype values can model hidden target fuzzy functions even though no training data are explicitly provided. Next, the proposed method is evaluated in terms of variations in specifying fuzzy numbers as genotype values. One of the mostly adopted fuzzy numbers is a symmetric triangular one that can be specified by its lower and upper bounds (LU) or its center and width (CW). Experimental results revealed that the LU model contributed better to the fuzzy ES than the CW model, which indicates that the LU model should be adopted in future applications of the proposed method.
Abstract: This paper studied the flow shop scheduling problem under machine availability constraints. The machines are subject to flexible preventive maintenance activities. The nonresumable scenario for the jobs was considered. That is, when a job is interrupted by an unavailability period of a machine it should be restarted from the beginning. The objective is to minimize the total tardiness time for the jobs and the advance/tardiness for the maintenance activities. To solve the problem, a genetic algorithm was developed and successfully tested and validated on many problem instances. The computational results showed that the new genetic algorithm outperforms another earlier proposed algorithm.
Abstract: This paper discusses micrometeorological aspects of the urban climate in three cities in Western São Paulo State: Presidente Prudente, Assis and Iepê. Particular attention is paid to the method used to estimate the components of the energy balance at the surface. Estimates of convective fluxes showed that the Bowen ratio was an indicator of the local climate and that its magnitude varied between 0.3 and 0.7. Maximum values for the Bowen ratio occurred earlier in Iepê (11:00 am) than in Presidente Prudente (4:00 pm). The results indicate that the Bowen ratio is modulated by the radiation balance at the surface and by different clusters of vegetation.
Abstract: The Portuguese footwear industry had in the last five years a remarkable performance in the exportation values, the trade balance and others economic indicators. After a long period of difficulties and with a strong reduction of companies and employees since 1994 until 2009, the Portuguese footwear industry changed the strategy and is now a success case between the international players of footwear. Only the Italian industry sells footwear with a higher value than the Portuguese and the distance between them is decreasing year by year. This paper analyses how the Portuguese footwear companies innovate and make innovation, according the classification proposed by the Oslo Manual. Also, analyses the strategy follow in the innovation process and shows the linkage between the type of innovation and the strategy of innovation. The research methodology was qualitative and the strategy for data collection was the case study. The qualitative data will be analyzed with the MAXQDA software. The economic results of the footwear companies studied shows differences between all of them and these differences are related with the innovation strategy adopted. The companies focused in product and marketing innovation, oriented to their target market, have higher ratios “turnover per worker” than the companies focused in process innovation. However, all the footwear companies in this “low-tech” industry create value and contribute to a positive foreign trade of 1.310 million euros in 2013. The growth strategies implemented has the participation of the sectorial organizations in several innovative projects. And it’s obvious that cooperation between all of them is a critical element to the performance achieved by the companies and the innovation observed. The Portuguese footwear sector has in the last years an excellent performance (economic results, exportation values, trade balance, brands and international image) and his performance is strongly related with the strategy in innovation followed, the type of innovation and the networks in the cluster. A simplified model, called “Ace of Diamonds”, is proposed by the authors and explains the way how this performance was reached by the seven companies that participate in the study (two of them are the leaders in the setor), and if this model can be used in others traditional and “low-tech” industries.
Abstract: One of the major problems being faced by human society is that the global temperature is believed to be rising due to human activity that releases carbon IV Oxide (CO2) to the atmosphere. Carbon IV Oxide is the most important greenhouse gas influencing global warming and possible climate change. With climate change becoming alarming, reducing CO2 in our atmosphere has become a primary goal of international efforts. Forest lands are major sink and could absorb large quantities of carbon if the trees are judiciously managed. The study aims at estimating the carbon sequestration capacity of Pinus caribaea (pine) and Tectona grandis (Teak) under the prevailing environmental conditions and exploring tree growth variables that influences the carbon sequestration capacity in Omo Forest Reserve, Ogun State, Nigeria. Improving forest management by manipulating growth characteristics that influences carbon sequestration could be an adaptive strategy of forestry to climate change. Random sampling was used to select Temporary Sample Plots (TSPs) in the study area from where complete enumeration of growth variables was carried out within the plots. The data collected were subjected to descriptive and correlational analyses. The results showed that average carbon stored by Pine and Teak are 994.4±188.3 Kg and 1350.7±180.6 Kg respectively. The difference in carbon stored in the species is significant enough to consider choice of species relevant in climate change adaptation strategy. Tree growth variables influence the capacity of the tree to sequester carbon. Height, diameter, volume, wood density and age are positively correlated to carbon sequestration. These tree growth variables could be manipulated by the forest manager as an adaptive strategy for climate change while plantations of high wood density species could be relevant for management strategy to increase carbon storage.
Abstract: Plate is one of the popular structural elements used in a wide range of industries and structures. They may be subjected to blast loads during explosion events, missile attacks or aircraft attacks. This study is to investigate dynamic responses of the rectangular plate subjected to explosive loads. The effects of material properties and plate thickness on responses of the plate are to be investigated. The compressive pressure is applied to the surface of the plate. Different amounts of thickness in the range from 1mm to 30mm are considered for the plate to evaluate the changes in responses of the plate with respect to plate thickness. Two different properties are considered for the steel. First, the analysis is performed by considering only the elastic-plastic properties for the steel plate. Later on damping is considered to investigate its effects on the responses of the plate. To do analysis, numerical method using a finite element based package ABAQUS is applied. Finally, dynamic responses and graphs showing the relation between maximum displacement of the plate and aim parameters are provided.
Abstract: The purpose of this study is to identify human walking vertical force by using FFT power spectrum density from the experimental acceleration data of the human body. An experiment on human walking is carried out on a stationary floor especially paying attention to higher components of dynamic vertical walking force. Based on measured acceleration data of the human lumbar part, not only in-phase component with frequency of 2fw, 3fw, but also in-opposite-phase component with frequency of 0.5 fw, 1.5 fw, 2.5 fw where fw is the walking rate is observed. The vertical vibration of pedestrian bridge induced by higher components of human walking vertical force is also discussed in this paper. A full scale measurement for the existing pedestrian bridge with center span length of 33 m is carried out focusing on the resonance phenomenon due to higher components of human walking vertical force. Dynamic response characteristics excited by these vertical higher components of human walking are revealed from the dynamic design viewpoint of pedestrian bridge.
Abstract: The objective of this paper is to analyze the role played by the institute of the public hearings in the Brazilian Supreme Court. The public hearings are regulated since 1999 by the Brazilian Laws nº 9.868, nº 9.882 and by the Intern Regiment of the Brazilian Supreme Court. According to this legislation, the public hearings are supposed to be called when a matter of circumstance of fact must be clarified, what can be done through the hearing of the testimonies of persons with expertise and authority in the theme related to the cause. This work aims to investigate what is the role played by the public hearings and by the experts in the Brazilian Supreme Court. The hypothesis of this research is that: (I) The public hearings in the Brazilian Supreme Court are used to uphold a rhetoric of a democratic legitimacy of the Court`s decisions; (II) The Legislative intentions have been distorted. To test this hypothesis, the adopted methodology involves an empirical study of the Brazilian jurisprudence. As a conclusion, it follows that the public hearings convened by the Brazilian Supreme Court do not correspond, in practice, to the role assigned to them by the Congress since they do not serve properly to epistemic interests. The public hearings not only do not legitimate democratically the decisions, but also, do not properly clarify technical issues.
Abstract: The importance of this study is to understand how Indonesian military court asserts its jurisdiction over military members who commit general crimes within the Indonesian military judiciary system in comparison to other countries. This research employs a normative-juridical approach in combination with historical and comparative-juridical approaches. The research specification is analytical-descriptive in nature, i.e. describing or outlining the principles, basic concepts, and norms related to military judiciary system, which are further analyzed within the context of implementation and as the inputs for military justice regulation under the Indonesian legal system. Main data used in this research are secondary data, including primary, secondary and tertiary legal sources. The research focuses on secondary data, while primary data are supplementary in nature. The validity of data is checked using multi-methods commonly known as triangulation, i.e. to reflect the efforts to gain an in-depth understanding of phenomena being studied. Here, the military element is kept intact in the judiciary process with due observance of the Military Criminal Justice System and the Military Command Development Principle. The Indonesian military judiciary jurisdiction over military members committing general crimes is based on national legal system and global development while taking into account the structure, composition and position of military forces within the state structure. Jurisdiction is formulated by setting forth the substantive norm of crimes that are military in nature. At the level of adjudication jurisdiction, the military court has a jurisdiction to adjudicate military personnel who commit general offences. At the level of execution jurisdiction, the military court has a jurisdiction to execute the sentence against military members who have been convicted with a final and binding judgement. Military court's jurisdiction needs to be expanded when the country is in the state of war.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: The world crude oil demand is projected to rise to 108.5 million bbl/d by the year 2035. With reserves estimated at 869 billion tonnes worldwide, coal remains an abundant resource. The aim of this work was to produce a high value hydrocarbon liquid product using a Direct Coal Liquefaction (DCL) process at, relatively mild operating conditions. Via hydrogenation, the temperature-staged approach was investigated in a dual reactor lab-scale pilot plant facility. The objectives included maximising thermal dissolution of the coal in the presence of tetralin as the hydrogen donor solvent in the first stage with 2:1 and 3:1 solvent: coal ratios. Subsequently, in the second stage, hydrogen saturation, in particular, hydrodesulphurization (HDS) performance was assessed. Two commercial hydrotreating catalysts were investigated viz. NickelMolybdenum (Ni-Mo) and Cobalt-Molybdenum (Co-Mo). GC-MS results identified 77 compounds and various functional groups present in the first and second stage liquid product. In the first stage 3:1 ratios and liquid product yields catalysed by magnetite were favoured. The second stage product distribution showed an increase in the BTX (Benzene, Toluene, Xylene) quality of the liquid product, branched chain alkanes and a reduction in the sulphur concentration. As an HDS performer and selectivity to the production of long and branched chain alkanes, Ni-Mo had an improved performance over Co-Mo. Co-Mo is selective to a higher concentration of cyclohexane. For 16 days on stream each, Ni-Mo had a higher activity than Co-Mo. The potential to cover the demand for low–sulphur, crude diesel and solvents from the production of high value hydrocarbon liquid in the said process, is thus demonstrated.
Abstract: In this study, we demonstrate a high-resolution
refractive index sensor based on a Magnetic Photonic Crystal (MPC)
composed of a triangular lattice array of air holes embedded in Si
matrix. A microcavity is created by changing the radius of an air hole
in the middle of the photonic crystal. The cavity filled with gyrotropic
materials can serve as a refractive index sensor. The shift of the
resonant frequency of the sensor is obtained numerically using finite
difference time domain method under different ambient conditions
having refractive index from n = 1.0 to n = 1.1. The numerical results
show that a tiny change in refractive index of Δn = 0.0001 is
distinguishable. In addition, the spectral response of the MPC sensor is
studied while an external magnetic field is present. The results show
that the MPC sensor exhibits a dramatic improvement in resolution.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The first laboratory synthesis of hard materials such as
diamond proceeded to attack of developing materials with high
hardness to compete diamond. Boron rich solids are good candidates
owing to their short interatomic bond lengths and strong covalent
character. Boron containing hard material was synthesized by modifiedmicrowave
method under nitrogen atmosphere by using a fuel
(glycine or urea), amorphous boron and/or boric acid in appropriate
molar ratio. Characterizations were done by x-ray diffraction (XRD),
Fourier transform infrared (FTIR) spectroscopy, scanning electron
microscopy/energy dispersive analyze (SEM/EDS), thermo
gravimetric/differential thermal analysis (TG/DTA).
Abstract: The end of the line controls of the finished products in
the automotive industry is important. The control that has been
conducted with the manual methods for the sliding doors tracks is not
sufficient and faulty products cannot be identified. As a result, the
customer has the faulty products. In the scope of this study, the
design criteria of the PLC integrated modular end of line control unit
has been examined, designed and manufactured to make the control
of the 10 different track profile to 2 different vehicles with an
objective to minimize the salvage costs by obtaining more sensitive,
certain and accurate measurement results. In the study that started
with literature and patent review, the design inputs have been
specified, the technical concept has been developed, computer
supported mechanic design, control system and automation design,
design review and design improvement have been made. Laser
analog sensors at high sensitivity, probes and modular blocks have
been used in the unit. The measurement has been conducted in the
system and it is observed that measurement results are more sensitive
than the previous methods that we use.