Abstract: This paper describes three lumped parameters models
for the study of the dynamic behavior of a boom crane. The models
here proposed allows to evaluate the fluctuations of the load arising
from the rope and structure elasticity and from the type of the
motion command imposed by the winch. A calculation software
was developed in order to determine the actual acceleration of the
lifted mass and the dynamic overload during the lifting phase. Some
application examples are presented, with the aim of showing the
correlation between the magnitude of the stress and the type of the
employed motion command.
Abstract: This paper presents the result of an experimental
investigation regarding the use of Fe2O3 nanoparticles added to
kerosene as a working fluid, under magnetic field for Copper
Oscillating Heat pipe with inclination angle of 0°(horizontal), 15°,
30°,45°, 60°,75° and 90° (vertical). The following were examined;
measure the temperature distribution and heat transfer rate on
Oscillating Heat Pipe (OHP), with magnetic field under different
angles. Results showed that the addition of Fe2O3 nanoparticles under
magnetic field improved thermal performance of OHP especially in
75°.
Abstract: Current study established for EEG signal analysis in
patients with language disorder. Language disorder can be defined as
meaningful delay in the use or understanding of spoken or written
language. The disorder can include the content or meaning of
language, its form, or its use. Here we applied Z-score, power
spectrum, and coherence methods to discriminate the language
disorder data from healthy ones. Power spectrum of each channel in
alpha, beta, gamma, delta, and theta frequency bands was measured.
In addition, intra hemispheric Z-score obtained by scoring algorithm.
Obtained results showed high Z-score and power spectrum in
posterior regions. Therefore, we can conclude that peoples with
language disorder have high brain activity in frontal region of brain
in comparison with healthy peoples. Results showed that high coherence correlates with irregularities
in the ERP and is often found during complex task, whereas low
coherence is often found in pathological conditions. The results of the
Z-score analysis of the brain dynamics showed higher Z-score peak
frequency in delta, theta and beta sub bands of Language Disorder
patients. In this analysis there were activity signs in both hemispheres
and the left-dominant hemisphere was more active than the right.
Abstract: This paper proposes for the first time symbolic
formula of the power spectrum of CMOS Cross Couple Oscillator
and its modified circuit. Many principles existed to derived power
spectrum in microwave textbook such as impedance, admittance
parameters, ABCD, H parameters, etc. It can be compared by graph
of power spectrum which methodology is the best from the point of
view of practical measurement setup such as condition of impedance
parameter which used superposition of current to derived (its current
injection at the other port of the circuit is zero, which is impossible in
reality). Four graphs of impedance parameters of cross couple
oscillator are proposed. After that four graphs of scattering
parameters of CMOS cross coupled oscillator will be shown.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.
Abstract: High moisture content in fruits generates post-harvest
problems such as mechanical, biochemical, microbial and physical
losses. Dehydration, which is based on the reduction of water activity
of the fruit, is a common option for overcoming such losses.
However, regular hot air drying could affect negatively the quality
properties of the fruit due to the long residence time at high
temperature. Power ultrasound (US) application during the
convective drying has been used as a novel method able to enhance
drying rate and, consequently, to decrease drying time. In the present
study, a new approach was tested to evaluate the effect of US on the
drying time, the final antioxidant activity (AA) and the total
polyphenol content (TPC) of banana slices (BS), mango slices (MS)
and guava slices (GS). There were also studied the drying kinetics
with nine different models from which water effective diffusivities
(Deff) (with or without shrinkage corrections) were calculated.
Compared with the corresponding control tests, US assisted drying
for fruit slices showed reductions in drying time between 16.23 and
30.19%, 11.34 and 32.73%, and 19.25 and 47.51% for the MS, BS
and GS respectively. Considering shrinkage effects, Deff calculated
values ranged from 1.67*10-10 to 3.18*10-10 m2/s, 3.96*10-10 and
5.57*10-10 m2/s and 4.61*10-10 to 8.16*10-10 m2/s for the BS, MS and
GS samples respectively. Reductions of TPC and AA (as DPPH)
were observed compared with the original content in fresh fruit data
in all kinds of drying assays.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: Financial inclusion has become a crucially important
factor in debates on economic inequality posing challenges to the
financial systems of countries around the world. Nowadays
governments and banks are concerned about creating products that
allow access to wide sectors of the population. The creation of
banking products by the financial sector for people with low incomes
tends to lead to improvements in the quality of life of vulnerable parts
of the population. In countries with notable social and economic
inequalities, financial inclusion is a key aspect for equitable
economic growth. This study is based on the case of Colombia, which is a country
with a strong record of economic growth over the past decade.
Nevertheless, corruption, unemployment, and poverty contribute to
uncertainty regarding the country’s future growth prospects. This study wants to explain the situation of financial exclusion and
financial inclusion with respect to the Colombian case. Financial
inclusion is going to be studied from the perspective of social
innovation.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: Recently, numerous documents including large
volumes of unstructured data and text have been created because of the
rapid increase in the use of social media and the Internet. Usually,
these documents are categorized for the convenience of users. Because
the accuracy of manual categorization is not guaranteed, and such
categorization requires a large amount of time and incurs huge costs.
Many studies on automatic categorization have been conducted to help
mitigate the limitations of manual categorization. Unfortunately, most
of these methods cannot be applied to categorize complex documents
with multiple topics because they work on the assumption that
individual documents can be categorized into single categories only.
Therefore, to overcome this limitation, some studies have attempted to
categorize each document into multiple categories. However, the
learning process employed in these studies involves training using a
multi-categorized document set. These methods therefore cannot be
applied to the multi-categorization of most documents unless
multi-categorized training sets using traditional multi-categorization
algorithms are provided. To overcome this limitation, in this study, we
review our novel methodology for extending the category of a
single-categorized document to multiple categorizes, and then
introduce a survey-based verification scenario for estimating the
accuracy of our automatic categorization methodology.
Abstract: For schools to be desirable places in which to work, it
is necessary for principals to recognise their teachers’ emotions, and
be sensitive to their needs. This necessitates that principals are
capable to correctly identify their emotionally intelligent behaviours
(EIBs) they need to use in order to be successful leaders. They also
need to have knowledge of their emotional intelligence and be able to
identify the factors and situations that evoke emotion at an
interpersonal level. If a principal is able to do this, then the control
and understanding of emotions and behaviours of oneself and others
could improve vastly. This study focuses on the interpersonal EIBS
of principals affecting the job satisfaction of teachers. The correlation
coefficients in this quantitative study strongly indicate that there is a
statistical significance between the respondents’ level of job
satisfaction, the rating of their principals’ EIBs and how they believe
their principals’ EIBs will affect their sense of job satisfaction. It can
be concluded from the data obtained in this study that there is a
significant correlation between the sense of job satisfaction of
teachers and their principals’ interpersonal EIBs. This means that the
more satisfied a teacher is at school, the more appropriate and
meaningful a principal’s EIBs will be. Conversely, the more
dissatisfied a teacher is at school the less appropriate and less
meaningful a principal’s interpersonal EIBs will be. This implies that
the leaders’ EIBs can be construed as one of the major factors
affecting the job satisfaction of employees.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: The hydrodynamic and thermal behaviors of fluid
flow in wavy microchannel are investigated numerically. Effects of
Reynolds number on the hydrodynamics and thermal behaviors are
investigated. Three cases of Reynolds number (580, 1244, and 1910)
are adopted in this study. It is found that the separation zone begin
appears when Reynolds number is greater than 1910 at the endsection
of the wave. Also it is found that dimensionless maximum
velocity at the mid-section of the wave decreases and becomes as a
turbulent behavior as Reynolds numbers increases. The maximum
temperature at the center line at the mid-section of the wave increases
as Reynolds number increases until it reaches the turbulent behavior
when Reynolds number is equal or greater than 1244, while this
behavior will be achieved at very high velocities at the end section of
the wave.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: The effect of molybdate addition to chloride
environment on resistance of AISI 316Ti stainless steel to pitting
corrosion was studied. Potentiodynamic polarisation tests were
performed in 1 M and 0.1 M chloride acidified solutions with various
additions of sodium molybdate at room temperature. The presented
results compare the effect of molybdate anions on quality of passive
film (expressed by the pitting potential) in both chloride solutions.
The pitting potential increases with the increase inhibitor
concentration. The inhibitive effect of molybdate ions is stronger in
chloride solution of lower aggressiveness (0.1M).
Abstract: Due to the fast and flawless technological innovation
there is a tremendous amount of data dumping all over the world in
every domain such as Pattern Recognition, Machine Learning, Spatial
Data Mining, Image Analysis, Fraudulent Analysis, World Wide
Web etc., This issue turns to be more essential for developing several
tools for data mining functionalities. The major aim of this paper is to
analyze various tools which are used to build a resourceful analytical
or descriptive model for handling large amount of information more
efficiently and user friendly. In this survey the diverse tools are
illustrated with their extensive technical paradigm, outstanding
graphical interface and inbuilt multipath algorithms in which it is
very useful for handling significant amount of data more indeed.